Cotech 36-1761 Manual

Cotech Lettelse 36-1761

Læs nedenfor 📖 manual på dansk for Cotech 36-1761 (4 sider) i kategorien Lettelse. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

ENGLISH

Ver. 200806

Spotlight Kit

18-2387/36-1761, 18-2388/36-1762, 18-2389/36-1763

Please read the entire instruction manual before using the product

and save it for future reference. We apologise for any text or

photographic errors and any changes of technical data. If you have

any questions concerning technical problems please contact our

Customer Service Department.

1. Safety

- Read all the instructions before you install and turn on the lights.

- The wiring should meet the required standards. If you are not

sure about anything, contact a qualied electrician.

- Make sure that the electrical specications are in accordance with

your installation. The circuit must be protected by a fuse on 10 A.

- The minimum area on the connection lead to the electrical

current is 1.5 mm².

- Before drilling in the ceiling, check for possible interferences

such as power lines.

- The metal piece that is used to show the spotlight in adjusted posi-

tion in the box should be removed and not be used at installation.

- Always turn off the power before mounting, connecting

or maintenance.

- Follow the instructions regarding minimum and maximum values.

Explanation of symbols

2. Contents

- 3 halogen lights 12 V/20 W incl. 1.5 cables

- Electronic transformer

- 1.5 m power lead

3. Installation

3.1 Before getting started

Tools required:

4. Care and Maintenance

- Always turn off the power before carrying out any maintenance.

- You may only replace the halogen light – any other repairs

should be carried out by a qualied electrician.

- Only use halogen lights that match the specications.

- Warning: Using accessories other than those recommended in

these instructions may lead to personal injury.

- This light kit is approved according to current standards.

Repairs must only be carried out by qualied personnel using

original spare parts.

- The transformer has a short circuit and surge protector that

shuts it off automatically if necessary. When the short circuit or

overload has been rectied the transformer starts again.

- The transformer has a thermal fuse which cuts the power if

overheated to prevent further damage.

4.1 Changing a light

1. Turn off the electricity.

2. Wait until the light has cooled.

3. Remove the spring that the light is connected with.

4. Remove the old light and replace it with a new.

5. Secure the light with the spring and then turn the power on again.

4.2 Cleaning

1. Cut the power before cleaning.

2. Wait until the light has cooled.

3. Clean the visible part of the light and the metal edge with

a lightly moistened cloth.

4. Never use alcohol, solvent or similar agents to clean the light.

Disposal

When it is time to dispose of the product, dispose of it according

to your local ordinances. If you are unsure please contact your

municipality.

Specications

Properties

External measurements 82 mm

Drill hole 74 mm

Minimum mounting height 150 mm

Minimum distance in between 2 lights 300 mm

Minimum distance in between light and wall 100 mm

Minimum distance to ammable surface 500 mm

Electrical Specications

Transformer 35-105 W dimmable

Primary voltage transformer 230 V AC, 50 Hz, cosØ=0,99

Secondary voltage transformer 11,6 V ~ RMS Max. 8.8 A

Connecting to the power point. Via plug

Lamp type 12 V, 20 W halogen

(MR16 GU5,3)

Class IP44

Class II

Class III

Minimum distance in between light and ammable surface.

Light source suitable for mounting on ammable surface.

Light source which will be used with self protective

tungsten halogen lights with built-in protective safety

feature and safety cover.

When it is time to dispose of the product, dispose of it

according to your local ordinances. If you are unsure

please contact your municipality.

3.2 Mounting

The transformer will be mounted in a ventilated space at a safe

distance from heat sources according to the illustration below.

- Always turn off the power before mounting, connecting

or maintenance.

- Only use included cables when connecting the light kit.

1. Measure the placement of the lights and

drill a hole with the diameter 74 mm. Mount

the transformer and pull the cables from the

transformer before mounting the lights.

3. Push the side clamps and slide the frame up until the clamps

lock in place on ceiling’s top.

4. Mount the next light with a minimum distance of 300 mm.

Warning:

The light source and its transformer may under no circumstances be

covered be insulation or similar materials.

Recommended installation zones in bathrooms

Dimensions according to standard IEC60364-7-701.

2. Connect the cable to the light.

3.3 Connectors

- Connect the lights’ plugs to the terminal block which is

connected to the transformer.

- Connect the transformer to the electric outlet (230 V AC, 50 Hz)

via a power switch.

Distance from heat sources.

Transformer

Electric outlet

230 V~

12 V–

Transformer

Produkt Specifikationer

Mærke:	Cotech
Kategori:	Lettelse
Model:	36-1761

Har du brug for hjælp?

Hvis du har brug for hjælp til Cotech 36-1761 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse Cotech Manualer

Cotech IPC15A3A-D3 Manual

30 August 2024

Cotech EMP701MD Manual

27 August 2024

Cotech IPC30SA1A Manual

16 August 2024

Cotech JF4011G Manual

14 August 2024

Cotech RP120W Manual

10 August 2024

Cotech 36-4137 Manual

8 August 2024

Cotech WCVC012W10 Manual

5 August 2024

Cotech TOE-12 Manual

5 August 2024

Cotech 36-6078 Manual

5 August 2024

Cotech IVY-405-11W Manual

4 August 2024

Lettelse Manualer

Nyeste Lettelse Manualer

Gemini GDL13T Manual

16 December 2024

Gemini GDL250 Manual

16 December 2024

Fuzzix Orion Manual

16 December 2024

BeamZ Phoenix 1200 Manual

15 December 2024

15 December 2024

15 December 2024

15 December 2024

15 December 2024

15 December 2024

15 December 2024