Datalogic LYNX MULTI-BATTERY CHARGER Manual
Datalogic
Stregkodescanner
LYNX MULTI-BATTERY CHARGER
Læs nedenfor 📖 manual på dansk for Datalogic LYNX MULTI-BATTERY CHARGER (1 sider) i kategorien Stregkodescanner. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
LYNX
MULTI-BATTERY CHARGER
The Multi-Battery Charger, with its 4 slots, allows you to
charge simultaneously 4 Lynx battery packs. Both standard
capacity battery (94ACC0064) and high capacity battery
(94ACC0065) can be recharged with this accessory.
Figure 1
POWER SUPPLY
Plug the power supply, already in the box, into the connector,
then plug the power supply into a socket. Use a country
specific power cord.
Figure 2
LED INDICATORS
Battery Charging Status LED Description
LED Status
Power Green It is constant when the
battery charger is powered
Charger off Empty slot
Red Charging
Green Charge completed
Red blinking Error
822001300
USING THE MULTI-BATTERY CHARGER
Charge Function
Correctly insert the battery pack into the slot: simply press it
into the slot until the battery latch is automatically closed;
charging starts automatically.
Figure 3
To remove the battery, release the latch on the battery pack as
showed in figure 4:
Figure 4
TECHNICAL FEATURES
ELECTRICAL
Power supply* 12V DC
Max consumption 5 A
CHARGING TIME
Std Battery 2h 30
High Cap Battery 4h
PHYSICAL
Dimensions (LxWxH) 210 x 149 x 48 mm
(8.3 x 5.9 x 1.9 in)
Weight (without batteries) 418 g (14.7 oz)
LEDs 4 Charger Status LEDs
1 Power on LED
ENVIRONMENTAL
Working temperature** 0° to +50 °C (+32° to +122 °F)
Storage temperature -20° to +70 °C (-4° to +158 °F)
Humidity 95% without condensation
Electrostatic discharge
EN 61000-4-2 4 KV contact / 8 KV air
* Use only DL approved power adapters
** When inserted in the spare slot, batteries must be charged at a
temperature ranging from 0° to 44 °C.
At higher values the charging may slow down.
Never charge the main device or spare batteries in a closed space
where excessive heat can build up.
FCC COMPLIANCE
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
Modifications or changes to this equipment without the
expressed written approval of Datalogic could void the
authority to use the equipment.
This device complies with PART 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
which may cause undesired operation.
Battery Charging
State LEDs
Power on LED
Produkt Specifikationer
| Mærke: | Datalogic |
| Kategori: | Stregkodescanner |
| Model: | LYNX MULTI-BATTERY CHARGER |
Har du brug for hjælp?
Hvis du har brug for hjælp til Datalogic LYNX MULTI-BATTERY CHARGER stil et spørgsmål nedenfor, og andre brugere vil svare dig
Stregkodescanner Datalogic Manualer
21 August 2024
20 August 2024
19 August 2024
18 August 2024
16 August 2024
16 August 2024
14 August 2024
10 August 2024
10 August 2024
9 August 2024
Datalogic Manualer
9 Oktober 2024
22 September 2024
12 September 2024
30 August 2024
21 August 2024
20 August 2024
19 August 2024
18 August 2024
16 August 2024
16 August 2024