Datalogic Skorpio X3 Multi Battery Charger Manual
Datalogic
Stregkodescanner
Skorpio X3 Multi Battery Charger
Læs nedenfor 📖 manual på dansk for Datalogic Skorpio X3 Multi Battery Charger (1 sider) i kategorien Stregkodescanner. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
SKORPIO™ X3
MULTI-BATTERY CHARGER
The Multi-Battery Charger, with its 4 slots, allows you to charge the
Skorpio X3 battery packs.
Figure 1
POWER SUPPLY
Plug the power supply into the connector, then plug the power supply
into a socket. Use a country specific power cord.
We recommend the power supply 94ACC1385.
Figure 2
LED INDICATORS
Battery Charging Status LED Description
LED Status
Power Green It is constant when the battery
charger is powered
Charger off Empty slot
Red Charging
Green Charge completed
Red blinking Error
822001270
USING THE MULTI-BATTERY CHARGER
Charge Function
Correctly insert the battery pack into the slot: simply press it into the slot
until the battery latch is automatically closed; charging starts
automatically.
Figure 3
To remove the battery, release the latch on the battery pack as showed
in figure 4:
Figure 4
TECHNICAL FEATURES
ELECTRICAL
Power supply* 12V DC
Max consumption 5 A
CHARGING TIME
Skorpio X3 Std Battery 4h 30
Skorpio X3 High Cap Battery 5h
PHYSICAL
Dimensions (LxWxH) 210 x 149 x 44 mm
(8.3 x 5.9 x 1.7 in)
Weight (without batteries) 418 g (14.7 oz)
LEDs 4 Charger Status LEDs
1 Power on LED
ENVIRONMENTAL
Working temperature** -10° to +50 °C (+14° to +122 °F)
Storage temperature -20° to +70 °C (-4° to +158 °F)
Humidity 95% without condensation
Electrostatic discharge
EN 61000-4-2 4 KV contact / 8 KV air
* Use only DL approved power adapters
** Spare batteries should be charged at an ambient temperature between
0 - 35º C to achieve the maximum charging rate. Never charge the
main device or spare batteries in a closed space (cabinet) where
excessive heat can build up.
FCC COMPLIANCE
his device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate
the equipment.
Battery Charging
State LEDs
Power on LED
Produkt Specifikationer
| Mærke: | Datalogic |
| Kategori: | Stregkodescanner |
| Model: | Skorpio X3 Multi Battery Charger |
Har du brug for hjælp?
Hvis du har brug for hjælp til Datalogic Skorpio X3 Multi Battery Charger stil et spørgsmål nedenfor, og andre brugere vil svare dig
Stregkodescanner Datalogic Manualer
21 August 2024
20 August 2024
19 August 2024
18 August 2024
16 August 2024
16 August 2024
14 August 2024
10 August 2024
10 August 2024
9 August 2024
Datalogic Manualer
9 Oktober 2024
22 September 2024
12 September 2024
30 August 2024
21 August 2024
20 August 2024
19 August 2024
18 August 2024
16 August 2024
16 August 2024