DeWalt DW610 Manual

DeWalt Router DW610

Læs nedenfor 📖 manual på dansk for DeWalt DW610 (4 sider) i kategorien Router. Denne guide var nyttig for 23 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

DW610 Router

Troupie Toupie électronique

Rebajadora con base fija

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUC-

TIVO ANTES DE USAR EL PRODUCTO.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT:

1-800-4-DEWALT (1-800-433-9258)

General Safety Instructions for All Tools

WARNING! Read and understand all instructions. Failure to follow all instructions listed

below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

• CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t use power

tools in damp or wet locations. Keep work area well lit.

• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces; for exam-

ple, pipes, radiators, ranges, and refrigerator enclosures.

• KEEP CHILDREN AWAY. All visitors should be kept away from work area. Do not let visitors con-

tact tool or extension cord.

• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up place

— out of reach of children.

• DON’T FORCE A TOOL. It will do the job better and safer at the rate for which it was intended.

• USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy duty tool. Don’t

use tool for purpose not intended; for example, don’t use circular saw for cutting tree limbs or

logs.

•DRESS PROPERLY. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,

clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught

in moving parts. Air vents often cover moving parts and should also be avoided.

• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.

• DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep

cord from heat, oil, and sharp edges.

• SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it frees

both hands to operate tool.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safe performance.

Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if

damaged have repaired by authorized service facility. Inspect extension cords periodically and

replace if damaged. Keep handles dry, clean, and free from oil and grease.

• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when changing

accessories, such as blades, bits, cutters.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and

adjusting wrenches are removed from tool before turning it on.

• AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on the switch. Be

sure the switch is off when plugging in.

• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords

intended for use outdoors and so marked.

• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are

tired.

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged

should be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mount-

ing, and any other conditions that may affect its operation. A guard or other part that is defective

should be properly repaired or replaced by an authorized service center unless otherwise indi-

cated elsewhere in this instruction manual. Have defective switches replaced by authorized ser-

vice center. Do not use tool if switch does not turn it on and off.

• DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or explosive

atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.

Additional Safety Rules for Routers

• KEEP HANDS AWAY from cutting area. Never reach under the material for any reason.

Hold front of tool by grasping the contoured gripping area. Do not insert fingers or thumb into the

vicinity of the cutter head. Keep the router base firmly in contact with the work when cutting. Do

not stabilize the router by holding the base.

• USE SHARP CUTTERS. Dull cutters may cause the router to swerve or stall under pressure.

• Never touch the bit immediately after use. It may be extremely hot.

• Be sure that the motor has stopped completely before you lay the router down. If the cutter head

is still spinning when the tool is layed down, it could cause injury or damage.

• Be sure that the router bit is clear of the workpiece before starting motor. If the bit is in contact

with the workpiece when the motor starts it could make the router jump, causing damage or

injury.

CAUTION: Wear appropriate personal hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorp-

tion of harmful chemicals.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

Grounding

This tool should be grounded while in use to protect the operator from electric shock. The tool

is equipped with an approved three-conductor cord and three-prong grounding type plug to fit

the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is

the grounding wire. Never connect the green (or green and yellow) wire to a live terminal.

If your unit is intended for use on less than 150 volts, it has a plug similar to that shown in Figure

A. An adapter, Figures B and C, is available for connecting Figure A plugs to two-prong recep-

tacles. The green-colored rigid ear, lug, etc., must be connected to a permanent ground such as

a properly grounded outlet box. Whenever the adapter is used, it must be held in place by a

metal screw.

NOTE: The 220 volt plug and plug outlet are different from those shown in Figures B and C.

WARNING: Improper connection of the equipment grounding conductor can result in the

risk of electric shock. Check with a qualified electrician or service person if you are in doubt

as to whether the outlet is properly grounded. Do not modify the plug provided with the appli-

ance. If it will not fit the outlet, a proper outlet must be installed by a qualified electrician.

We recommend that you never disassemble the tool or try to do any rewiring in the electrical

system. Any repairs should be performed only by authorized service centers. Should you be

determined to make a repair yourself, remember that the green colored wire is the grounding

wire. Never connect this green wire to a live terminal. If you replace the plug on the power cord,

be sure to connect the green wire only to the grounding (longest) prong on a three-prong plug.

Never remove the grounding prong.

Extension Cords

Double insulated tools have 2-wire cords and can be used with 2-wire or 3-wire extension cords.

Only round jacketed extension cords should be used, and we recommend that they be listed by

Underwriters Laboratories (U.L.). If the extension will be used outside, the cord must be suitable

for outdoor use. Any cord marked as outdoor can be used for indoor work. The letters “W” or

“WA” on the cord jacket indicate that the cord is suitable for outdoor use.

An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and

to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater

the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more

than one extension to make up the total length, be sure each individual extension contains at

least the minimum wire size.

To determine the minimum wire size required, refer to the extension cord chart.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

6 - 10 18 16 14 12

Before using an extension cord, inspect it for loose or exposed wires, damaged insulation, and

defective fittings. Make any needed repairs or replace the cord if necessary.

Collet

IMPORTANT NOTE: NEVER TIGHTEN COLLET NUT IF THERE IS NO CUTTER IN THE COL-

LET. COMPRESSING COLLET TOO MUCH MIGHT RESULT IN DAMAGE.

A 1/2" collet is installed in your router and a 1/4" collet is included in the package.

To Change Collet

Unplug the router. Using the supplied wrenches as necessary, simply unscrew and remove the

collet nut. Pull the collet out of the end of the shaft.

Installing Router Bits

TURN OFF AND UNPLUG ROUTER.

To install a router bit, first open the collet by loosening (counterclockwise) the collet nut. Use the

supplied wrenches if necessary. Insert the shaft of the desired bit into the collet as far as it will

go and then pull it out about 1/16" (1.5 mm). Hold the router shaft with one of the wrenches and

firmly tighten the collet nut with the other.

CAUTION: Router Bits Are Sharp. Use Care In Handling Them.

Depth Adjustment

TURN OFF AND UNPLUG ROUTER.

Follow the steps below to adjust router cutting depth.

1. Turn off the router and unplug the cord.

2. Select and install the desired bit.

3. Place the router down on its base on your work piece.

4. Loosen the wing nut (A) on the depth adjuster and turn the depth adjusting knob (B), shown

in Figure 1, to raise or lower the bit until it just touches the work piece.

5. Rotate the black calibrated knob (A) to align the “0” mark with the notch (B) in the housing,

as shown in Figure 2.

6. Turn the router upside down and put it on the work piece.

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color

scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box con-

figuration; and the array of lozenge-shaped humps on the surface of the tool.

A B C D

GROUNDING PIN

GROUNDED

OUTLET

BOX GROUNDING

MEANS

GROUNDING PIN

ADAPTER

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Router
Model:	DW610

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DW610 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Router DeWalt Manualer

10 September 2024

16 August 2024

14 August 2024

9 August 2024

DeWalt DWP611PK Manual

5 August 2024

DeWalt DW618B3E Manual

29 Juli 2024

DeWalt DW618B3 Manual

25 Juli 2024

DeWalt DW616 Manual

22 Juli 2024

DeWalt DW616PK Manual

20 Juli 2024

DeWalt DWE6000 Manual

16 Maj 2024

Router Manualer

Nyeste Router Manualer

Huawei HWD11 Manual

21 December 2024

Asus TUF Gaming BE6500 Manual

19 December 2024

Vimar 01548 Manual

15 December 2024

D-Link DWP-812KT Manual

13 December 2024

Evolution EVCTL10B Manual

12 December 2024

Teltonika RUTM08 Manual

11 December 2024

Starlink Mini Manual

10 December 2024

Arris SURFboard G18 Manual

10 December 2024

Asus USB-N11 Manual

9 December 2024

Asus RX3042H Manual

9 December 2024