DSC EV-DW4975 Manual

DSC Deur-/ramme sensor EV-DW4975

Læs nedenfor 📖 manual på dansk for DSC EV-DW4975 (1 sider) i kategorien Deur-/ramme sensor. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/1
EV-DW4975 Vanishing Door/Window Contact
Installation Manual
Introduction
The EV-DW4975 is the industries thinnest supervised
door/window contact allowing a multitude of applications
while hiding the transmitter on a door or window frame. The
EV-DW4975 uses a replaceable lithium battery and should
last 5 years under normal usage.
Install or Replacing the Battery
The EV-DW4975 uses a Panasonic CR2032 Lithium Battery
and is shipped not installed to save battery life.
Follow the steps below to install or replace the battery.
1) Using a coin (Figure 1) or a flat head screw driver (Figure 2)
insert into the notch located on the case and gently twist to
open. Lift up and pull the case outward to open (Figure 3).
2) Insert Battery (figure 4) + side facing UP.
Use care when installing the battery and observe the correct
polarity when the battery is inserted. Use only Panasonic
Lithium CR2032 batteries for replacement.
WARNING!: Battery may explode if mistreated.
Do not recharge, disassemble or dispose of in fire.
Mount Transmitter and Magnet
1) Mount the EV-DW4975 on any window or door frame using the supplied
double strick tape or screws (Figure 5).
2) Find the notch on the outside of the EV-DW4975 enclosure. Align the
magnet with the notches and ensure that the distance is no greater than
5/8 of an inch (Figure 6).
Enrolling
Refer to your installation manual for enrolling wireless devices into a
DSC control panel.
Specifications
• Frequency 433.92
• Transmission: ASK
• Operating Temperature: -10C-+50C
• Nominal Battery Life: 5 Years. Varies with Usage and Temperature
• Battery Type: Panasonic CR2032
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC: The term ‘IC:’ before the radio certification number only signifies that Industry Canada technical specifications were met.
Figure 3 Figure 4
Figure 1 Figure 2
Figure 5
Figure 6
Technical Support:
(866) 908-TECH (8324)
©2006 Secure Wireless
EV-DW4975 Vanishing Door/Window Contact
Installation Manual
Introduction
The EV-DW4975 is the industries thinnest supervised
door/window contact allowing a multitude of applications
while hiding the transmitter on a door or window frame. The
EV-DW4975 uses a replaceable lithium battery and should
last 5 years under normal usage.
Install or Replacing the Battery
The EV-DW4975 uses a Panasonic CR2032 Lithium Battery
and is shipped not installed to save battery life.
Follow the steps below to install or replace the battery.
1) Using a coin (Figure 1) or a flat head screw driver (Figure 2)
insert into the notch located on the case and gently twist to
open. Lift up and pull the case outward to open (Figure 3).
2) Insert Battery (figure 4) + side facing UP.
Use care when installing the battery and observe the correct
polarity when the battery is inserted. Use only Panasonic
Lithium CR2032 batteries for replacement.
WARNING!: Battery may explode if mistreated.
Do not recharge, disassemble or dispose of in fire.
Mount Transmitter and Magnet
1) Mount the EV-DW4975 on any window or door frame using the supplied
double strick tape or screws (Figure 5).
2) Find the notch on the outside of the EV-DW4975 enclosure. Align the
magnet with the notches and ensure that the distance is no greater than
5/8 of an inch (Figure 6).
Enrolling
Refer to your installation manual for enrolling wireless devices into a
DSC control panel.
Specifications
• Frequency 433.92
• Transmission: ASK
• Operating Temperature: -10C-+50C
• Nominal Battery Life: 5 Years. Varies with Usage and Temperature
• Battery Type: Panasonic CR2032
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC: The term ‘IC:’ before the radio certification number only signifies that Industry Canada technical specifications were met.
Figure 3 Figure 4
Figure 1 Figure 2
Figure 5
Figure 6
Technical Support:
(866) 908-TECH (8324)
©2006 Secure Wireless

Produkt Specifikationer

Mærke: DSC
Kategori: Deur-/ramme sensor
Model: EV-DW4975

Har du brug for hjælp?

Hvis du har brug for hjælp til DSC EV-DW4975 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Deur-/ramme sensor DSC Manualer

DSC

DSC EV-DW4975 Manual

27 Juli 2024

Deur-/ramme sensor Manualer

Nyeste Deur-/ramme sensor Manualer

ORNO

ORNO OR-SH-17600 Manual

6 September 2024
ORNO

ORNO OR-SH-17601 Manual

6 September 2024
Emos

Emos THS916A Manual

4 September 2024
Emos

Emos GS827 Manual

4 September 2024
Emos

Emos GS869 Manual

4 September 2024
Avidsen

Avidsen HomeSensor Window Manual

4 September 2024
Kanlux

Kanlux ROLF JQ-L Manual

4 September 2024
Kanlux

Kanlux SENTO Manual

4 September 2024
Kanlux

Kanlux MARID JQ-L Manual

4 September 2024
Optex

Optex TX/RX-TX Manual

3 September 2024