DSC PG9994 Manual

DSC Bevægelsesdetektor PG9994

Læs nedenfor 📖 manual på dansk for DSC PG9994 (7 sider) i kategorien Bevægelsesdetektor. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/7

PG9994/PG8994/PG4994

PowerG, Wireless, High-security PIR Motion

Outdoor Mirror Detector Installation

Instructions

Overview

The PGx994 is a PowerG wireless, outdoor, digital mirror PIR

detector which uses eight PIR sensors, each acting as a Quad

detector to accurately and reliably determine whether an alarm

is justified. Features & benefits include:

• Optimum performance even in poor weather conditions

such as snow, rain, dust, wind and direct sunlight.

• Tamper protection prevents opening and removal from wall

• Built-in link quality indicators reduce installation time by

eliminating the need for the installer to physically approach

the control panel.

• Microprocessor-controlled compensation.

• Immunity to pets weighing up to 18 Kg (40lb).

Note: Pet immunity feature has not been evaluated to UL 639

or ULC-S306-03 due to the feature not being addressed in

either standard.

Device Setup

WARNING! To comply with FCC

and IC RF exposure compliance

requirements, the PIR detector should

be located at a distance of at least 20

cm from all persons during normal

operation. The antennas used for this

product must not be co-located or

operated in conjunction with any

other antenna or transmitter.

Note: The PG Series wireless PIR

Motion detectors shall be installed

and used within an environment that

provides the pollution degree max 2 and overvoltages category

II in NON HAZARDOUS LOCATIONS. The equipment is

designed to be installed only by qualified service persons.

Note: To ensure the continued operation of all wireless devices

after performing a system default, a global upload of all wire-

less programming via DLS is recommended before defaulting

the system. After completing the system default, download the

wireless programming.

Legend

A. LED

B. Enroll button

C. Tamper switch

D. Bracket release

E. Horizontal view of coverage area

F. Vertical view of coverage area

G. Vertical angle

H. For wall tamper

Note: Back tamper switch is required for UL commercial bur-

glary installations.

Install the battery

It is recommended to perform the first batteries insertion on a

flat surface. After battery insertion, the LED will flash for 60

seconds and then the detector will enter a 15 minute local diag-

nostic mode.

Note: When manually programming wireless devices, if a

device has been powered up for more than 48 hours it cannot be

enrolled into the system until the device has been tampered and

restored. When programming the panel using the Quick Enroll

procedure follow the steps detailed in Enroll the Device into the

System.

Note: After restoring a low battery trouble the system may take

up to 5 minutes to clear the trouble.

Enroll the Device into the System

To quick enroll:

1. On a keypad press [*] [8] [Installer Code] [804] [000].

2. Press and hold the device enroll button until the LED lights

steady and then release the enroll button while the LED is

still lit. A confirmation message then appears on the

keypad.

3. Press [*] key to confirm ID.

4. Enter [3 digit zone #].

5. Enter [3 digit zone type].

6. Enter [1 digit partition #] for all desired partitions and

press [#]. If using an LCD keypad you can scroll to the

desired partitions and press [*] to toggle the partition.

7. On an LCD keypad enter the label by using word library.

To pre-enroll:

1. Remotely configure the unique ID number into the system.

For more information see the HSM2HOST manual.

2. When on-site, press the device enroll button.

Note: If the wireless device has been powered for more than 48

hours without being enrolled, tamper and restore the device to

enroll it.

Placement and Walk Testing

Before permanently mounting any wireless device, temporarily

mount the device and perform a Placement test. Perform a walk

test of the coverage area at least once a year to ensure that the

detector is working correctly.

1. Tamper the device by removing the cover.

2. Restore the tamper.

The device now

enters Placement

test mode for 15

minutes.

3. Trip the device and

the red LED blinks

once to identify that

a signal is being sent

to the receiver and

then blinks three

times to identify the

signal strength. To

perform a walk test,

walk across the far

end of coverage

pattern in both

directions. The

following table indicates received signal strength

indication.

IMPORTANT! Only GOOD or STRONG signal strengths are

acceptable. If you receive a POOR signal from the device, re-

locate it and re-test until a GOOD or STRONG signal is

received.

Note: For UL/ULC installations, only STRONG signal levels

are acceptable. After installation verify the product functional-

ity in conjunction with the compatible receivers HSM2HOST9,

HS2LCDRF(P)9, HS2ICNRF(P)9 and PG9920.

Note: For detailed Placement instructions refer to the control

panel Reference Guide.

Mounting the Device

Installation Notes: The top cover should only be accessed by

authorized service personnel or manufacturer. Do not obscure

the detector field of view with large objects. Install in position

such that expected intruder motion is perpendicular to the zones

of detection.

Alarms triggered by conditions such as weather, blowing leaves

and brush, or related environmental conditions, etc., need to be

considered when assessing the installation and application. If

nuisance trips are not tolerable it is recommended that the wire-

less outdoor intrusion detection unit is enrolled in the system to

a zone that is defined as a trouble alarm circuit.

1. Fix the bracket firmly on a stable wall or pillar. The

orientation of the fixed bracket must be as parallel as

possible to the surveyed ground surface.

2. Mark drilling point

3. Drill

4. Fasten with three long screws

5. Fasten the detector to the bracket with two short screws.

6. Adjust the detector's

horizontal and vertical

angles, according to the

surveyed ground surface.

The vertical angle indicator

position for various

installation height and

coverage distance

combinations is detailed in

the following table (the

information refers to a

relatively flat surveyed

area. Verify the vertical

adjustment by walk-test).

LED Operation

Configuration

To enter the wireless configuration section enter [804][Zone

Number].

Device Toggles

Device Options

Specifications

Caution! Risk of explosion if battery is replaced by an incor-

rect type. Dispose of used batteries according to the manufac-

turer's instructions and according to local rules and regulations.

Batteries are to be replaced by service persons only.

OPTICAL

Black Mirror Max. Coverage: At least 12 m (40 ft) / 90°

Detector Technology: 8 independent quad PIR detectors oper-

ating in true Quad configuration

Pet Immunity: Up to 18 Kg (40 lb)

ELECTRICAL

Input Power: Two 3V CR123A Lithium batteries

Note: For UL installations use Gold Peak (GP) only.

Battery Life (for typical use): minimum one year, typical 3

years (not verified by UL/ULC)

Low Battery Threshold: 4.0 V

WIRELESS

Frequency Band (MHz): CE Listed PG4994: 433MHz; CE/

EN listed PG8994: 868MHz; FCC/IC/UL/ULC listed PG9994:

912-919MHz

Communication Protocol: PowerG

Tamper Alert Reported when a tamper event occurs and in any

subsequent message, until the tamper switch is restored

MOUNTING

Mounting type: Wall mounting

Mounting Height: 1.5 – 3.0 m (5 – 10 ft). Must be 8 feet for

UL/ULC listed installations.

Horizontal Adjustment: -45° to +45°, in 5° steps

Vertical Adjustment: 0° to -10°, in 2.5° steps

ENVIRONMENTAL

Temperature range: -40ºC to +70ºC (UL/ULC only verified

the range -35ºC to +66ºC)

Relative Humidity: up to max. 93%RH, non-condensing

White Light Immunity: Above 25000 lux

PHYSICAL

Size (H x L x W): 157 x 147 x 124 mm (6-3/16 x 5-13/16 x 4-

7/8”)

Weight (with battery): 600 g (21 oz)

Color: White or gray

COMPATIBLE RECEIVERS

433MHz Band: HSM2HOST4; HS2LCDRF(P)4;HS2IC-

NRF(P)4; PG4920

868MHz Band: HSM2HOST8; HS2LCDRF(P)8; HS2IC-

NRF(P)8;PG8920

912-919MHz Band: HSM2HOST9; HS2LCDRF(P)9; HS2IC-

NRF(P)9; PG9920

Note: Only devices operating in band 912-919MHz are UL/

ULC listed.

UL/ULC Notes

Only models PG9994, PG9994P operating in the frequency

band 912-919MHz are UL/ULC listed. The PG9994, PG9994P

has been listed by UL for commercial and residential burglary

applications and by ULC for residential burglary applications in

accordance with the requirements in the Standards UL 639 and

ULC-S306 for Intrusion Detection Units.

For UL/ULC installations use these device only in conjunction

with compatible DSC wireless receivers: HSM2HOST9,

HS2LCDRF(P)9, HS2ICNRF(P)9 and PG9920. After installa-

tion verify the product functionality in conjunction with the

compatible receiver used.

Europe: The PG4994 and PG8994 are compliant with the RTTE

requirements - Directive 1999/5/EC of the European Parliament and of

the Council of 9 March 1999. The PG8994 is certified by Applica Test

and Certification to the following standards: EN50131-2-2 GRADE 2,

CLASS IV, EN50131-6 Type C. Applica Test andApplica Test and Certification has

certified only the 868 MHz variant of this product. According to EN 50131-1:2006 and

A1:2009, this equipment can be applied in installed systems up to and including

Security Grade 2, Environmental Class II. UK: The PG8994 is suitable for use in

systems installed to conform to PD6662:2010 at Grade 2 and environmental class 2

BS8243. The Power G peripheral devices have two- way communication functionality,

providing additional benefits as described in the technical brochure. This functionality

has not been tested to comply with the respective technical requirements and should

therefore be considered outside the scope of the product’s certification

FCC COMPLIANCE STATEMENT

WARNING! Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in residential installations. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

and television reception.

However, there is no guarantee that interference will not occur in a particular

installation. If this device does cause such interference, which can be verified by

turning the device off and on, the user is encouraged to eliminate the interference by

one or more of the following measures:

– Re-orient or re-locate the receiving antenna.

– Increase the distance between the device and the receiver.

– Connect the device to an outlet on a circuit different from the one that supplies power

to the receiver.

– Consult the dealer or an experienced radio/TV technician.

This equipment complies with FCC and IC RF radiation exposure limits set forth for an

uncontrolled environment.

This device complies with FCC Rules Part 15 and with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any

interference that may be received or that may cause undesired operation.

Le present appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence. L'exploita-

tion est autorisee aux deux conditions suivantes :(1) l'appareil

ne doit pas produire de brouillage, et (2) l'utilisateur de l'appar-

eil doit accepter tout brouillage radioelectrique subi, meme si le

brouillage est susceptible d'en compromettre le fonctionne-

ment.

PG9994/PG8994/PG4994

Instructions d'installation du détecteur de

mouvements IPR PowerG, à miroir, extérieur,

sans fil, de haute sécurité

Vue d'ensemble

Le PGx994 est un détecteur numérique IPR PowerG à miroir,

extérieur, sans fil qui met en œuvre huit capteurs IPR, chacun

agissant comme un détecteur à quatre cellules pour déterminer

de façon sûre et précise si une alarme est justifiée. Les car-

actéristiques et les avantages incluent :

• Des performances optimales même sous de mauvaises

conditions météorologiques comme de la neige, de la pluie,

du vent, en cas d'exposition à de la poussière ou aux rayons

directs du soleil.

• La protection anti-sabotage empêche le dispositif d'être

ouvert ou retiré du mur.

• Les indicateurs de qualité de liaison intégrés réduisent les

temps d'installation en supprimant la nécessité de

l'installateur d'être physiquement à proximité de la centrale.

• Correction apportée par microprocesseur.

• Insensibilité aux animaux d'un poids jusqu'à 18 kg (40 lb).

Remarque : La fonction d'insensibilité aux animaux n'a pas été

évaluée pour les normes UL 639 ou ULC-S306-03 parce qu'elle

n'est pas abordée par les deux normes

LED response Signal Strength

Green LED blinks STRONG

Orange LED blinks GOOD

Red LED blinks POOR

No blinks No communication

LED Indications Event

Red LED blinks Stabilization (warm-up 60

sec)

Red LED on 0.2 sec. Tamper open / close

Red LED blinks twice One quad PIR detection in

diagnostic mode

Red LED on 2 sec. Intruder alarm

[001][01] Alarm LED - Default [Y]

Enables the devices LED to activate when an alarm

event occurs.

[001][04] Supervision - Default [Y]

Enables supervision of the device.

[001][11] 24Hr/ Night - Default [Y]

4 5

Mounting

Height

Coverage Distance

2m /

6.7ft

4m /

13ft

6m /

20ft

8m /

26ft

10m/

33 ft

12m/

39 ft

3.0m/10ft - 1 2 2 3 3

2.5m / 8 ft 1 1 2 3 4 4

2.0m / 7 ft 1 2 3 4 5 5

1.5m / 5 ft 2 3 4 5 - -

Define whether motion alarms are always enabled

or only enabled at night. For UL/ULC installations

night mode is to only be used to supplement the

protection covering the detection area.

[003] Hightraffic Shutdown - Default [01]

Activating this feature helps conserve battery power

when the system is disarmed by configuring a reporting

timer. When motion is detected, the device transmits an

alarm to the receiver and will not report any further

events until the timer expires. Any motion detected

during the configured period will be reported once the

timer expires. No Delay causes the device to report an

alarm each time the detector is tripped.

[01] Detector Dis-

abled (while dis-

armed)

[02] No Delay [03] 5 second

delay

[04] 15 second

delay

[05] 30 second

delay

[06] 1m delay

[07] 5m delay [08] 10m delay [09] 20m delay

[10] 60m delay

[007] Detection Sensitivity - Default [02]

Selects the sensitivity range of PIR devices.

[01] Low Sensi-

tivity

[02] High Sensi-

tivity

[03] UL Standard

D-304675

Produkt Specifikationer

Mærke:	DSC
Kategori:	Bevægelsesdetektor
Model:	PG9994

Har du brug for hjælp?

Hvis du har brug for hjælp til DSC PG9994 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor DSC Manualer

13 September 2024

28 Juli 2024

28 Juli 2024

27 Juli 2024

26 Juli 2024

23 Juli 2024

21 Juli 2024

19 Juli 2024

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Optex FLX-S Manual

17 December 2024

EQ-3 HM-Sec-MDIR-2 Manual

16 December 2024

Optex SIP-100 Manual

16 December 2024

Optex SL-350QDM Manual

16 December 2024

Optex SIP-3020WF Manual

16 December 2024

16 December 2024

16 December 2024

15 December 2024

15 December 2024

Vimar 14485.SL Manual

15 December 2024