Escape P6 Air Manual

Escape Højttaler P6 Air

Læs nedenfor 📖 manual på dansk for Escape P6 Air (2 sider) i kategorien Højttaler. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
EscapeTM
P6 Air
Thank you for your purchase!
Thank you for purchasing the ESCAPE P6 Air, a portable High End speaker that supports both
Chromecast Audio, AirPlay2, Spotify Connect and Roon (endpoint).
1
2TURNING ON THE UNIT
Press the power button [ ] for a few seconds until the LED of the volume up button
[ ] and presets lights up briefly.
Wait until the P6 Air is in setup mode. The WIFI Led will then flash white 0.5s on and 0.5s off.
• Step 1: Download the Google Home-app [ ] to your phone or tablet to connect the
P6 Air with your wireless network. Ensure that your phone or tablet is connected with
the same WiFi network that you wish to use to set up the P6 Air.
• Step 2: Wait until the P6 Air is in configuration mode.
The [ ] LED on the P6 Air flashes white 0.5s on/off.
• Step 3: Open the Google Home app [ ] and select the [ ] symbol at top left on
the start screen or select “Set up Escape P6 Air”. Follow the steps set out in
the Google Home app.
Setup is complete. The [ ] LED lights up in solid white. Open your favourite music app
and select the AirPlay 2 symbol [ ] ] (iOS devices only) or the Cast symbool [ (iOS
and Android devices) and stream the music to the P6 Air. Or stream directly via Spotify
Connect.
Tip: Select the P6 Air in the Google Home app, go to device settings and activate
“full dynamic range”.
Tip: Group a combination of speakers via the Google Home app to play music
synchronously throughout the home via Cast. Note: This function is not supported
for Chromecast (1st generation) or devices with Chromecast built in.
CONFIGURATION IN AIRPLAY 2 AND SPOTIFY CONNECT ONLY, VIA AN IPHONE OR IPAD.
• Step 1: Ensure that your iPhone or iPad is connected with the same WiFi network that
you wish to use to set up the P6 Air. Wait until the P6 Air is in configuration mode.
The [ ] LED on the P6 Air flashes white 0.5s on/off.
• Step 2: Open “settings” on your iPhone or iPad [ ]. The P6 Air will create a
temporary network and will appear in the list of available networks. Important!
Do not select the temporary Escape P6 Air network (xxxxxxx) in the list of available
networks. Instead select the “Escape P6 Air (xxxxxx)” under the message
“Configure new AirPlay loudspeaker”. Follow the
steps set out under AirPlay configuration. Setup is
complete. Open your favourite music app and
select the AirPlay 2 symbol. [ ]
Note: if the “Configure new AirPlay loudspeaker” message is no longer visible then carry out
a reset on the P6 Air and allow sufficient time for the device to start up again.
Tip: You can mix several different AirPlay 2 compatible loudspeakers or modules to allow
music streaming in several rooms. AirPlay 2 is however not available on Android devices.
AirPlay 2 is supported on a MacBook or IMac via Apple Music and on a Windows PC
via iTunes and Apple Music.
USING SPOTIFY CONNECT.
Spotify® is a digital music service providing access to millions of songs. Spotify® Connect can be
used to create a connection between the P6 Air and the internet, using the Spotify® app for iOS or
Android, Mac or PC. You can make and receive telephone calls without interrupting the music. Once
you have connected with the P6 Air you can switch off your mobile device or computer and the music
will continue to play. Spotify® Connect can only play on a single speaker at any time.
ROON READY
Roon uses a cutting edge audio transport protocol which not only supports high resolution
audio but also offers 2-way communication between Roon Ready endpoints and the Roon
server. Being Roon Ready means that the Escape P6 Air uses the high end Roon RAAT streaming
technology (Roon Advanced Audio Transport). This delivers an incredible user interface, easy
installation, rock steady day-to-day reliability and the highest level of audio performance,
without compromises. You can find more information on the www.roonlabs.com website.
USING THE ESCAPE REMOTE APP
Download the Escape™ Remote app via the Google Play or Apple App store and follow the
steps on the screen to get the most out of the P6 Air.
Note: The P6 Air can only retain a single WiFi network at any one time. If you modify your WiFi
network you must reset the P6 Air to the new network. You may first need to carry out a reset
on the P6 Air.
AUTOMATIC SOFTWARE UPDATES
The P6 Air’s internal software will be updated automatically when a new version is available,
provided the device is powered up and connected with a WiFi network. The mode LED flashes
red-green-blue every 0.5 seconds during an update, and the device will restart automatically
when the update is complete. Ensure that the P6 Air remains switched on during the update.
BLUETOOTH VERBINDING
Streaming music to the P6 Air via wireless Bluetooth® technology. Wait until the P6 Air is in
configuration mode or connected to a WIFI network. The [ ] LED on the P6 Air flashes white
0.5s on/off or is permanently on Briefly press the Bluetooth® key to initiate the Bluetooth®
connection. The status LED will flash blue and white. Go to Settings on your Apple® or Android™
device, select Bluetooth® in the connections list and switch on Bluetooth®.
Select Escape™ P6 Air xxxx in the list of devices. xxxx stands for the last 4 letter/digit
combination in the device’s unique serial number. You will find the full serial number on the
packaging or on the label on the underside of the device. The blue LED will illuminate steadily
once the connection is created.
Important! The P6 Air only remembers the last Bluetooth® device previously connected and
always prioritizes a WIFI connection when available. The P6 Air does not support Twin mode in
Bluetooth®.
Note: If the Bluetooth® connection failed and your mobile device asks you to forget the device,
P6 Air may not reappear in the list. In that case, turn Bluetooth® off on your mobile device and
turn it on again. P6 Air will then be listed again.
Overview functions of control buttons
BUTTON FUNCTION
On/off button
Turn the Escape™ P6 Air on and off. To turn on the P6 Air, press the
power button for 2 seconds until the LED of the volume up button
[ ] and presets lights up briefly. Briefly press the power button
to turn off the P6 BT.
Skip backwards
Press the skip backwards [ ] button to replay the song from
the beginning or press it twice in quick succession to go back to
the previous song. (This function does not work with airable radio
stations)
Play/pause Start or pause the music.
Skip forward
Play the next song. (This function does not work with
airable radio stations)
Decrease volume
Press the [ ] briefly to decrease the volume step by step.
To decrease the volume quickly, press and hold the [ ].
Increase volume
Press the [ ] briefly to increase the volume step by step.
To increase the volume quickly, press and hold the [ ].
5 sec
Keypad lock
Press the skip backwards button for 5 seconds until you hear
a confirmation tone. The keypad is now locked. To confirm,
the skip backwards LED starts flashing three times each
time you touch any key.
5 sec
Keypad unlock
Press the skip forward button for 5 seconds until you hear
a confirmation tone. The keyboard is now unlocked.
Standby mode The standby mode is activated by default. This means that when
the unit is turned on and does not receive any audio signal for
20minutes, the P6 Air enters standby mode to save power.
The power button will blink, and all other LEDs will turn off.
Press the power button to turn on the P6 Air again. Standby
mode can be turned off through the Escape Remote App.
Power-LED - battery status indicator
LED-APPEARANCE BATTERY STATUS
Flashing red for
3 seconds and white
for 0.5 seconds
The battery charge has reached approximately 10%. The unit is not
connected to a power outlet and the battery needs to be charged.
Solid red The unit is connected to a power outlet and is charging.
White The battery is fully charged.
Rapidly flashing red
for 10 seconds
Battery error, for example when the power cable is connected to
a power outlet but no battery has been installed.
For more information, download the extended user manual from the website www.escapespeakers.com
Programming of the 3 presets on
the P6 Air keyboard
WIFI-Led and Bluetooth® status indicator
Warranty and regulations
Limited warranty for the product
The product is covered by a 1-year limited warranty (*) in accordance with the Escape™ P6 Air User Manual. The warranty
includes all parts and labour required to repair the product. This warranty does not cover damage caused by misuse,
accident, misuse, negligence or improper operation or installation, products that have been altered or products whose
identification number or serial number has been altered, defaced or removed. For this warranty to apply, you must use
the product in accordance with the instructions. (*) The limited warranty on Escape™ products is not subject to change
but is subject to alternative legal regulations that may vary from country to country.
Battery Warranty Limitation
The battery is guaranteed for 6 months from date of purchase worldwide.
Returning a P6 Air for repair
Repack the speaker in its original packaging or in a corrugated carton with at least 7.5 cm of resilient material
to protect it from damage in transit. Escape bv is not responsible for any damage in transit.
European Union
Escape bv hereby declares that this product is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53 / EU and all other applicable EU Directives.
IMPORTANT INFORMATION FOR CORRECT OPERATION OF THE P6 AIR
The P6 Air creates a wireless connection with your WiFi router. Ensure that you have
a sufficiently strong WiFi signal in locations where you wish to use the P6 Air.
ESCAPE REMOTE APP
Use of the dedicated application for the P6 Air is strongly recommended. Escape Remote
It can be downloaded free from the Apple App Store (iOS) and the Google Play Store (Android)
AIRABLE RADIO
Using the Escape Remote app you can select the airable catalogue, with more than 30,000
radio stations around the world and 25,000 podcasts. This enormous catalogue can be sorted
by region, genre, popularity and quality. The internet radio stations are managed by airable
GmbH, with a team ensuring that new content is constantly added, creating an unlimited source
of freely accessible music, news and entertainment. This service falls outside the responsibility
of Escape bv. and works only when P6 Air is in WIFI mode (not in Bluetooth®)
The IPX4 rating of a product means it is suitable for all
weather conditions and can withstand strong water
splashes. However, it is not resistant to immersion.
DE
ENG
CHARGING THE INTERNAL BATTERY
• Connect the enclosed power cord to the input
of the device (at the bottom of the unit).
• Plug the power cord into an electrical outlet
• The red power LED [ ] on the keyboard will
light up to indicate that the battery is charging.
Leave the unit connected to the mains until
the red LED goes out. The battery is then fully
charged.
• Remove the power cord and close the
protective cover.
• A full charge cycle of the battery takes
approximately two to three hours. Never leave
the P6 Air unattended while charging.
Enjoy your Escape™ P6 Air in 3 steps
Select an airable radio station via the Escape Remote app. While the airable radio station is
playing, press the desired preset buttons on the top of the P6 Air for 4 seconds until you hear
a confirmation tone. Presets are selected by briefly pressing the button. Stored presets can be
erased through the Escape Remote app or reprogrammed by pressing the preset again
for 4seconds.
IDEAL LISTENING POSITION
• The P6 Air’s specially developed DSP is set to “wide” mode for
a three-dimensional sound reproduction.
• Turn the speaker slightly towards the listening position for optimal
soundstage. This allows the listener to hear the location of different
instruments when listening to a particular piece of music.
• The “wide” mode can be changed to “direct” if desired via
the Escape Remote app.
L R
Preset 1
Preset 2
Preset 3
EU WEEE
CONNECTING THE P6 AIR WITH YOUR WIRELESS NETWORK TO STREAM MUSIC
SPOTIFY CONNECT, AIRPLAY 2 AND CHROMECAST SETTINGS VIA THE GOOGLE HOME APP
3
MODE/STATUS LED (RED, GREEN,
BLUE, WHITE)
DEFINITION
P6 Air is starting up
Flashing green
0.2s on and 0.2s off
P6 Air has just been powered on and in booting state.
(takes +/- 45 seconds)
DSP initialization
Green Solid P6 Air is in DSP initialization mode.
Searching available
network(s)
White/Green blinking
0.5s White and 0.5s Green
P6 Air is in access point (AP) mode. Searching for all
available wireless networks. (+/- 20 seconds)
Setup Mode
White blinking 0.5s on
and 0.5s off
Wireless network(s) found. User need to connect P6 Air
to the wireless network of his choice via Google Home
App (ChromeCast Audio and AirPlay 2 setup) or iOS®
device (AirPlay 2 setup only)
Connected
White Solid Successful network connection with known credentials.
Network Source
White Solid Speaker in Spotify Connect or AirPlay or Cast mode.
Factory Reset
White - Magenta
0.5s White and 0.5s
Magenta
A factory reset triggered - restart booting stage.
Firmware update
in progress
Red-Green-Blue repeat
0.5s-0.5s-0.5s
Firmware update in progress via one of the following:
• Programming the P6 Air via webpage.
• Connecting to the network and OTA Server.
• Downloading firmware from the OTA server.
Firmware update error
Red Blinking
0.5s on and 0.5s off
File transfer error (while downloading FW.bin file)
• Flash write error (while writing in flash)
• Network error (while connecting to OTA Server)
• Downloading firmware failed.
Bluetooth® Pairing
Blue / White Blinking
0.5s blue and 0.5s white
Bluetooth® not paired (discoverable)
Bluetooth® source
Blue Solid Switch to Bluetooth® source (if network is not setup,
it will turn to setup mode also)
Bluetooth® pairing
Important! Bluetooth® pairing button can only be activated when the device is in wifi setup
mode (wifi LED flashes white 0.5s on and 0.5s off) or when the P6 Air is connected to a
wireless network (WIFI LED permanently lit white). Press the Bluetooth® button briefly until
you hear a confirmation tone. 1) If the Bluetooth® pairing list is empty, it will enter pairing
mode. 2) If the Bluetooth® pairing list is not empty, it will try to connect to the previous
phone within 15 seconds. If it fails to connect to a phone within 15 seconds, the BT pairing
process will start automatically after 15 seconds. 3) It is possible to reselect the WIFI
connection on the P6 Air if it is already set by briefly pressing the WIFI switch.
(Status LED goes from blue to white)
Bluetooth® memory reset
Press and hold the Bluetooth® button for more than 10 seconds.
All Bluetooth® devices stored in memory will be deleted.
WIFI and factory reset
A factory reset can only be performed after the P6 Air is fully booted up. Press the
WIFI button for more than 5 seconds until you hear a double confirmation tone.
Quick Start Guide
Carefully read all safety precautions in the attached document or on the website
www.escapespeakers.com before using this product.
P6 Air QSG ENG (V2021.09)

Produkt Specifikationer

Mærke: Escape
Kategori: Højttaler
Model: P6 Air

Har du brug for hjælp?

Hvis du har brug for hjælp til Escape P6 Air stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Escape Manualer

Escape

Escape P6 Air Manual

31 August 2024
Escape

Escape M1 Air Manual

31 August 2024
Escape

Escape P9 Manual

31 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

NGS

NGS WILD Space 2 Manual

17 December 2024
Canton

Canton Chrono SL 520.2 Manual

16 December 2024
Canton

Canton GLE 456 Center Manual

16 December 2024
Canton

Canton Vento 820.2 Manual

16 December 2024
Canton

Canton Chrono SLS 780 DC Manual

16 December 2024
Canton

Canton In Wall 500 LCR Manual

16 December 2024
Canton

Canton InWall 949 LCR Manual

16 December 2024
Canton

Canton InWall 845 LCR Manual

16 December 2024
Canton

Canton InCeiling 855 Manual

16 December 2024
Canton

Canton Atelier 950 Manual

16 December 2024