Eureka Tundern Cove 6 Manual

Eureka Telt Tundern Cove 6

Læs nedenfor 📖 manual på dansk for Eureka Tundern Cove 6 (2 sider) i kategorien Telt. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
1. Unroll your tent and separate the tent from the fly. Assemble
the frame poles being sure all connections are complete.
2. Spread out the tent in desired site location. Stake corner fac-
ing into wind in windy conditions.
3. Locate the pole sleeves found on the top of the tent. Slide
poles through sleeves so they form an X pattern on the still
flat tent. In one corner insert the corner pin into the base of
the pole. Move to the other end of the same pole, diagonally
opposite, and insert the corner pin into this pole end. In this
process the pole will flex into a hoop shape. Be careful dur-
ing this process to not over stress the pole. You can relieve
excess pressure by grabbing the pole sleeve end and pull to
center the sleeves over the mid section of the hoop.
4. Repeat step 3 with the second long frame pole.
5. Attach remaining clips to frame at the peak.
6. Tent can now be staked in location.
7. Spread the fly sheet over the tent positioning the vestibule
over the tent door that has yellow webbing in one corner as
this is the front.
8. Feed the vestibule pole through the vestibule pole sleeve al-
ways pushing, never pulling.
9. Take one end of the vestibule pole and insert a pin into the
pole end. The pin will be located on the corner ring of the
tent.
10. Repeat step 9 with the other end of the pole. During this
step the vestibule pole will flex into a hoop. Attach any re-
maining clips
11. Attach all four fly sheet corners, with the hooks provided, to
the four tent corner rings.
12. Stretch out the vestibules and stake out using the fabric
loops
13. On each side are positions supplied to pull out the fly sheet
and stake.
14. On the underside of the tent fly sheet locate the Velcro fas-
teners and wrap around the tent poles.
15. If required, for windy
conditions you can
use the pre-rigged
guylines to stake out
for more stability.
ASSEMBLY INSTRUCTIONS for Tundern Cove 6/Evasion
Important
Please set up your tent prior to your first trip to ensure you
are familiar with set up and the tent is in proper condition.
Always choose a site with good drainage. Inspect the site and
remove any sharp or protruding objects that could damage
the tent floor.
Although major seams are taped we recommend seam seal-
ing guy out locations due to stitching through tape, and any
other seams where taping may not have been possible
1. The suns UV rays can be harmful even with technical ad-
vances in fabrics. Prolonged exposure could result in fading
and possibly fabric disintegration. When choosing a site try
to pitch the tent in a shaded area. Do not leave a tent up
longer than necessary.
2. Fuels can damage tents as can DEET found in many insect
repellents.
3. All major seams are factory taped. Over time seams could
experience delamination. Simply clean the seam and apply
seam sealer that can be purchased at most outdoor stores.
4. Avoid storing your tent in a hot location.
5. Please be sure to store your tent dry. Mildew can occur on
waterproof coatings if stored when wet.
TIPS
SET UP


Produkt Specifikationer

Mærke: Eureka
Kategori: Telt
Model: Tundern Cove 6

Har du brug for hjælp?

Hvis du har brug for hjælp til Eureka Tundern Cove 6 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Telt Eureka Manualer

Telt Manualer

Nyeste Telt Manualer

De Waard

De Waard Zeester Manual

7 Oktober 2024
SereneLife

SereneLife SLTET30 Manual

1 Oktober 2024
Calima

Calima 46074 Manual

1 Oktober 2024
SereneLife

SereneLife SLPTSR107 Manual

30 September 2024
Vaude

Vaude Badawi Long 6 Manual

29 September 2024
De Waard

De Waard Stormmeeuw Manual

25 September 2024
Vrijbuiter

Vrijbuiter Stormvogel Manual

22 September 2024
Crivit

Crivit IAN 86428 Manual

20 September 2024