Exalux Connect RX200N Manual

Exalux Ikke kategoriseret Connect RX200N

Læs nedenfor 📖 manual på dansk for Exalux Connect RX200N (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
1 - GENERAL INFORMATION
This instruction manual contains important notifications regarding the
safe use of the EXALUX™ CONNECT RX200N.
Please take the time to read this manual carefully and thoroughly
before installing and operating the system. We recommend you keep
a copy for future use and you transfer it to the buyer if you resell the
system.
EXALUX™ reserves the right to modify and upgrade its range of
products, with no obligation to integrate these changes into products
already sold. Therefore, all the information found in this manual is
subject to change without notice.
2 - TECHNICAL SPECIFICATIONS
3 - OPERATING CONDITIONS
4 - RADIO INTERFACE
5 - WARRANTY
EXALUX™ cannot be responsible for material or personal damage
resulting from improper use of the product or non-compliance to the
instructions. The warranty will not be applied in these cases.
6 - OVERVIEW
The CONNECT RX200N is a wireless DMX/RDM receiver that uses
LumenRadio CRMX technology (2.4GHz). This system allows the users
to connect to DMX/RDM enabled fixtures wirelessly, several tens
meters away from a CRMX transmitter. CONNECT RX200N can receive
an entire DMX universe (512 channels).
Power supply input
Power consumption
DMX/RDM connector
Supported protocols
Display
Control
Housing
Protection
Certifications
Weight
Dimensions
2.1 x 5.5mm DC jack
0.9W max
XLR5 pins Female (Neutrik®)
DMX512-A ANSI E1.11
RDM - ANSI E1.20
6 LED indicators
1 push button on membrane switch
Aluminium, steel, plastic
IP30
CE
80g (without cables)
26x32x76mm (without antenna)
Input voltage
Storage temperature
Operationg temperature
+ 4.5Vdc
- 10°C
+ 26Vdc
Minimum Maximum
+ 55°C
- 20°C + 75°C
Standard / technology
Frequency range
CRMX by LumenRadio™
2.402 ~ 2.480 GHz
2dBi - 50ohms - ±90° hinged
Panel mount (not removable)
20dBm /100mW
(ETSI compliant)
GFSK Cognitive coexistence
(dynamically avoids occupied frequencies)
500 – 1000m
(open field line of sight - depending on the
transmitter and the environnement)
Antenna
RF output
RF modulation
Range
7 - CONTROL
8 - POWER SUPPLY
The CONNECT RX200N is powered from the 2.1x5.5mm
DCJack connector. When powered, the red «POWER»
indicator turns on.
Input Voltage: From +4.5Vdc to +26Vdc
Typical working voltage:
• for USB battery powering5Vdc
(using USB-DCjack cord provided with the device)
• for V-mount battery powering14.8Vdc
(using DTAP-DCjack cord provided with the device)
9 - DMX/RDM OUTPUT
The CONNECT RX200N is designed for DMX/RDM equipments. The signal
received from the radio emitter is forwarded to the XLR5, with the standard
pinout (1:Ground / 2:Data- / 3:Data+).
The blue indicator «DMX» turns on when a DMX signal is received and
outputed on the XLR5.
LINKED indicator (Blue)
- ON : receiver linked with transmitter
- OFF : receiver not linked
DMX indicator (Blue)
- ON : valid DMX stream reception
- OFF : no DMX
POWER indicator (Red)
- ON : device is powered
- OFF : device is off
UNLINK button
Hold button pressed for
> 3 seconds to unlink
device from transmitter
SIGNAL indicators
(Green)
Excellent reception
Correct reception
Bad reception
Powering the system out of this
range can cause malfunctions
and the destruction of the product.
DC
input
Positive polarity
Adhesive cable mount
Zip tie (max tie width: 4.1mm)
DCjack cord locking system:
The CONNECT RX200N is provided
with an adhesive cable mount and
zip ties. You can lock the cable with zip
tie to avoid unintentional cord
disconnection.
(5) Not used
(4) Not used
(3) Data +
(2) Data -
(1) Ground
10 - LINKING WITH TRANSMITTER
It is necessary to link the RX200N to a emitter following this procedure:
- Make sure all devices to be paired are powered.
- Start the linking procedure by pressing the dedicated button on the
emitter.
- During the linking period (10s), the DMX signal is not transmitted. Any
unlinked CONNECT RX200N in range will automatically link to the emitter. If
a CONNECT RX200N is linked to an emitter, the blue «LINK» indicator turns
on (even if the transmitter is off).
Several receivers CONNECT RX200N can be linked to the same emitter
during a single procedure.
11 - UNLINKING RECEIVERS
At any time, it is possible to reset the configuration of the receiver by
unlinking from the emitter. To do so, press the «UNLINK» button during 3
seconds, until the «LINK» indicator turns off.
12 - RADIO
The antenna is manually adjustable ( 90°). Take care not to exceed over ±
this angle. The antenna is not removable.
A three-level gauge provides feedback on the radio signal strength. In
order to optimize the radio communication, it is also recommended to
install the transmitters and receivers in open spaces, without large metalic
objects. It is also recommanded to place the antennas as described in
the following image.
13 - SAFETY INSTRUCTIONS
Proper use:
This unit is designed to control any DMX or DMX/RDM equipment. Use the
device only in its intended use as described in this manual.
The device should only be used by people in full possession of their
physical, sensory and mental abilities who must have the knowledge and
experience required. All the other persons are only allowed to use the
device under the supervision or direction of a person responsible for their
safety.
Safety:
Risk of electric shock
This system requires voltage, which can result in an electrical shock. Never
remove covers. The parts inside the device are maintenance free.
Dangers for children
Ensure a proper disposal of plastic envelopes and packaging. They should
not be near babies nor young children: suffocation danger. Make sure
that children do not remove and swallow small parts of the unit (e.g.
knobs, screws or similar). Never leave unattended children use electrical
devices.
Electric shock caused by a short circuit
Do not modify the power cord nor the plug. In case of noncompliance,
there is a risk of electric shock and fire hazard. If in doubt, contact a
certified technician.
Risk of fire
Never cover the device nor its ventilation slots. Do not install the device
close to a source of heat. Keep the device away from flames.
Terms of use
The device is designed for indoor use. To prevent damage, do not expose
the product to liquid or moisture. Avoid direct sunlight, clogging and
strong vibrations.
CARE
- Unplug the unit when cleaning it and during all maintenance operations
- Do not remove the serial number sticker.
- Do not use cleaning product: use a dry cloth and rub gently.
- Store the device in a clean, dry place, away from direct exposure from
sunlight and dust.
-90° max +90° max
TX
TX
RX
RX
CONNECT RX200N
2.4GHz RDM RECEIVER
EXALUX is a registered trademark of
the French Tech company LEDIXIS
1 rue de la Noë - Bat. IM3
CS 12111 44322 Nantes cedex 3
FRANCE
+33 (0)9.72.45.70.43
www.exalux.eu
Information:
contact@exalux.eu
Technical support:
support@exalux.eu
Last updated on 10-2020

Produkt Specifikationer

Mærke: Exalux
Kategori: Ikke kategoriseret
Model: Connect RX200N

Har du brug for hjælp?

Hvis du har brug for hjælp til Exalux Connect RX200N stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Exalux Manualer

Exalux

Exalux Connect TX100N Manual

20 August 2024
Exalux

Exalux Connect RX200N Manual

20 August 2024
Exalux

Exalux Connect RX100S Manual

19 August 2024
Exalux

Exalux Connect One Manual

19 August 2024
Exalux

Exalux Control One Manual

18 August 2024
Exalux

Exalux Control Touch Manual

17 August 2024
Exalux

Exalux Control Sky Manual

17 August 2024
Exalux

Exalux Connect+ Manual

22 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SKROSS

SKROSS World Adapter Pro+ Manual

26 November 2024
SKROSS

SKROSS PRO – World & USB Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024