Gamber-Johnson 7160-1333 Manual


Læs nedenfor 📖 manual på dansk for Gamber-Johnson 7160-1333 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Rev.A INST-881
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Attach the power supply to the overhead guard leg with the power supply clamp.
Place the power supply againts the overhead guard leg and clamp in place with
the the diamond plates shown below. Rotate the diamond plates so the bolts are
as tight as possible to the overhead guard leg. Once the power supply is
clamped in place the excess length of the bolts can be cut off if desired. Note:
the power supply can be clamped somewhere other than the overhead guard
leg if desired. For example it could be clamped to one of the upper bars on the
overhead guard.
PS-001
Printing Spec:
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Form Revision
Power Supply Clamp
7160-1333
© Copyright 2018 Gamber-Johnson, LLC
Product
INSTALLATION INSTRUCTIONS
guard leg
overhead
power
supply
diamond plate
bracket
3/8" mounting
hardware
diamond bracket
rotated so bolts are
close to overhead
guard leg


Produkt Specifikationer

Mærke: Gamber-Johnson
Kategori: Ikke kategoriseret
Model: 7160-1333

Har du brug for hjælp?

Hvis du har brug for hjælp til Gamber-Johnson 7160-1333 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Gamber-Johnson Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MPM

MPM -48-CW-48 Manual

9 November 2024
Alpine

Alpine KAE-123C Manual

8 November 2024
IFM

IFM AC434S Manual

8 November 2024
Alpine

Alpine SBS-0515 Manual

8 November 2024
Alpine

Alpine KCE-103V Manual

8 November 2024
Alpine

Alpine KCE-104V Manual

8 November 2024
Advantech

Advantech ECU-1051TL Manual

8 November 2024
Alpine

Alpine DDC-R13A Manual

8 November 2024
Alpine

Alpine HCE-C200F Manual

8 November 2024
Alpine

Alpine CRM-1652RF Manual

8 November 2024