Hikvision DS-KIS604-S Manual

Hikvision Samtaleanlæg DS-KIS604-S

Læs nedenfor 📖 manual på dansk for Hikvision DS-KIS604-S (7 sider) i kategorien Samtaleanlæg. Denne guide var nyttig for 15 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/7
DS-KIS604-S
Video Intercom Network Bundle UD17150B-A
34
Screen Microphone
2Debugging Port
3Network Interface
4
Loudspeaker
5TF Card Slot
6Alarm Terminal
7Reserved
8
Note:
The appearance of the device varies according to different models. Refers to the actual device for detailed
informaon.
The debugging port is used for debugging only.
Terminal and Wiring
2
There are 20 pins in the terminal on the rear panel of the indoor staon: 2 RS-485 pins, 5
reserved pins, 4 relay output pins, 8 alarm input pins, and 1 GND pin.
Installaon
3
It supports wall mounng. There are two installaon modes.
ENGLISH
Diagram References
Appearance
1
Installaon Accessory Descripon
The wall mounng plate and juncon box are required to install the indoor staon onto
the wall.
The dimension of juncon box should be 75 mm (width) 75 mm (length) 50 mm
× ×
(depth). The dimension of wall mounng plate is shown.
Wall Mounng with juncon Box
Make sure the device in the package is in good condion and all the assembly parts
are included.
The power supply the indoor staon supports is 12 VDC. Please make sure your
power supply matches your indoor staon.
Make sure all related equipments are power-off during the installaon.
Check the product specificaon for the installaon environment.
Before You Start
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the lock catch
will be locked automacally.
1
3
Geng Started
4
You are required to acvate the device first by sengs a strong password before you
can use the device.
Acvate Indoor Staon
1
Quick Configuraon
2
Refers to Video Intercom Network Indoor Staon Configuraon Guide (Scan the QR code) for details.
Refers to Video Intercom Network Indoor Staon Operaon Guide (Scan the QR code) for details.
6789
5
1
2
Power Terminal
9
Note: There are 20 pins in the terminal on the rear panel of the DS-KH6320-TE1: 11 reserved pins, 8 alarm
input pins, and 1 GND pin. Please refer to the specific model.
Wall Mounng without juncon Box
1. Insert 2 expansion tubes into the wall.
2. Fix the wall mounng plate to the juncon box with 2 screws.
3. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the lock catch
will be locked automacally.
3
Rear Panel (without Interface)
Lock Catch Lock Catch
Lock Catch Lock Catch
Hook Hook
Hook Hook
Screw Wall Mounng Plate Wall
Rear Panel (without Interface)
Lock Catch Lock Catch
Lock Catch Lock Catch
Hook Hook
Hook Hook
Screw Wall Mounng Plate Juncon Box Wall
Scan the QR code to get the
Operaon Guide for detailed
informaon.
Scan the QR code to get the
Configuraon Guide for detailed
informaon.
RS-485
Reserved
2
Relay Output
Alarm
Input
Device
RS-485+
RS-485-
RES
RES
RES
RES
RES
NO2
NO1
COM1
COM2
AIN7
AIN6
AIN5
AIN4
AIN3
AIN2
AIN1
GND
AIN8
Red
Red
Blue
Green
Yellow
Yellow
White
Black
Red
Black
Black
Black
Black
White
White
White
White
White
White
White
122
Unit:mm
100
64.85
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automacally.
3. Configure the indoor staon parameters.
- .Select Indoor Staon and tap Next to link main door staon.
a. Edit Floor and Room No.
b. Create and confirm SIP register password.
Note: If you want to add the indoor staon to the door staon, the SIP password of the indoor staon
should be the same as the registraon password of the door staon.
c. Tap Advanced Sengs to edit Community No, Building No. and Unit No.
d. Oponal: Enable Indoor Staon Sengs and select the indoor staon to link.
- . Select Indoor Extension and tap Next to link indoor staon.
a. Edit No., Room Name.
b. Create and confirm SIP register password.
4. Linked related devices and tap Next. If the device and the indoor staon are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the sengs icon to pop up the Network Sengs page.
b. Edit the network parameters of the door staon manually or enable DHCP to get
the network parameters automacally.
e. Tap OK to save the sengs.
5. Tap Finish to save the sengs.
1
DS-KH6320-WTE1
Network Indoor Staon
1. Power on the device. It will enter the acvaon page automacally.
2. Create a password and confirm it.
3. Tap OK to acvate the indoor staon.
4. Oponal: Bind email address. You can reset the acvaon/admin password vial the
email fi you forget your password.


Produkt Specifikationer

Mærke: Hikvision
Kategori: Samtaleanlæg
Model: DS-KIS604-S

Har du brug for hjælp?

Hvis du har brug for hjælp til Hikvision DS-KIS604-S stil et spørgsmål nedenfor, og andre brugere vil svare dig




Samtaleanlæg Hikvision Manualer

Samtaleanlæg Manualer

Nyeste Samtaleanlæg Manualer

Vimar

Vimar K40955 Manual

17 November 2024
Vimar

Vimar K40930 Manual

17 November 2024
Viking

Viking E-1600A Manual

25 September 2024
Viking

Viking E-20TF-IP Manual

25 September 2024
Viking

Viking E-32-EWP Manual

25 September 2024
Viking

Viking E-20B Manual

25 September 2024
Viking

Viking E-40-BK Manual

24 September 2024
Viking

Viking E-20-IP Manual

24 September 2024