Inovonics EchoStream EN1223D Manual

Inovonics Controller EchoStream EN1223D

Læs nedenfor 📖 manual på dansk for Inovonics EchoStream EN1223D (1 sider) i kategorien Controller. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
© Inovonics, 2009 - www.inovonics.com
EN1223D EchoStream® Double-Button Panic
Alarm
Installation and Operation Manual - 05583A, April 29,
2009
1 Overview
Inovonics EN1223D panic alarm transmitters are our smallest, lightest, and
most versatile pendants.
Note: For UL installations, refer to the EN4216R Installation and Operation
Manual.
1.1 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics Wireless
technical services:
E-mail: support@inovonics.com
Phone: (800) 782-2709; (303) 939-9336
1.2 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics Wireless
technical services:
E-mail: support@inovonics.com
Phone: (800) 782-2709
1.3 Transmitter Components
Figure 1 Transmitter components
2 Installation and Startup
2.1 Installation Notes
These products are designed to be maintained by professional
security technicians.
Products are intended for indoor use.
Manually test all products weekly.
2.2 Install/Replace the Batteries
1. If present, remove the 3 three housing screws on the back of the
transmitter.
2. Open the housing.
3. Install the new batteries, ensuring the positive terminals (+) face the
indicated side of the holder.
2.3 Select the Frequency Band
EchoStream products are able to use a range of radio frequencies, and
must be configured for your geographic area. To configure the transmitter:
1. Place a selection jumper on the appropriate frequency band selection
pins.
Place the jumper on the top two pins, marked NZ, to set the frequency
range to 921-928 MHz for New Zealand.
Place the jumper on the bottom two pins, marked AU, to set the
frequency range to 915-928 MHz for Australia.
Leave the jumper off the pins to set the frequency range to 902-928
MHz for North America.
Note: Only devices set for use in North America are configured for UL
installations.
2. Press the Reset button to complete conguration.
Caution: When pressing the button, make sure you don’t also touch Reset
the frequency band selection pins. Touching the frequency band selection
pins while pressing the Reset button can inadvertently set the transmitter
to the wrong frequency band.
2.4 Register the Transmitter
The transmitter must be registered with the system in order to be monitored
and supervised. When supervised, the transmitter will send a check-in
message to the serial receiver or network coordinator every three minutes.
Each transmitter has a unique factory-programmed identification number.
Refer to the receiver’s installation instructions for details on registering a
transmitter.
1. When prompted by the receiver to reset transmitter, press the Reset
button.
Caution: The transmitter should be tested after registration to ensure
operation. To test the transmitter, activate each of the conditions and
ensure an appropriate response.
3 Operate the Transmitter
To activate single button transmitters, press the button for at least one
second. To activate double button transmitters, press both buttons
simultaneously. Alarm signals are transmitted multiple times and are
indicated by the blinking transmission LED. When the buttons are released,
the transmitter sends an alarm restoral signal.To test a transmitter, activate
the alarm by pressing the button(s).
4 Specifications
Dimensions: 5.6 x 4.8 x 1.8 cm (2.2 x 1.9 0.72”)
Operating temperature: 0 to 60°C (32 to 140°F), 90% relative humidity,
noncondensing
Typical battery life: 3-5 years
Battery type (BAT609): Renata CR2450, Panasonic CR2450
Power requirement: 3 VDC, 60 mA
UL listings: UL 1023, ULC/ORD-C1023-74
Compatible receiver: EN4216R
Note: Specifications and data are subject to change without notice.
5 Warranty and Disclaimer
Note: Changes or modifications to this unit not expressly approved by
Inovonics Wireless Corporation may void the installer's authority to operate
the equipment as well as the product warranty.
Inovonics Wireless Corporation ("Inovonics") warrants its products
("Product" or "Products") to conform to its own specifications and to be free
of defects in materials and workmanship under normal use for a period of
thirty-six (36) months from the date of manufacture. Within the warranty
period, Inovonics will repair or replace, at its option, all or any part of the
warranted Product. Inovonics will not be responsible for dismantling and/or
reinstallation charges. To exercise the warranty, the User ("User", "Installer"
or "Consumer") must work directly through their authorized distributor who
will be given a Return Material Authorization ("RMA") number by Inovonics.
Details of shipment will be arranged directly through the authorized
distributor.
This warranty is void in cases of improper installation, misuse, failure to
follow installation and operating instructions, alteration, accident or
tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other warranties,
obligations or liabilities, whether written, oral, express, or implied. There is
no warranty by Inovonics that Inovonics product will be merchantable or fit
for any particular purpose, nor is there any other warranty, expressed or
implied, except as such is expressly set forth herein. In no event shall
Inovonics be liable for an incidental, consequential, indirect, special, or
exemplary damages, including but not limited to loss of profit, revenue, or
contract, loss of use, cost of down time, or interruption of business, nor any
claim made by distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics does not
authorize any person to act on its behalf to modify or extend this warranty.
This warranty will apply only to Inovonics Poducts. Inovonics will not be
liable for any direct, incidental, or consequential damage or loss
whatsoever, caused by the malfunction of Product due to products,
accessories, or attachments of other manufacturers, including batteries,
used in conjunction with Inovonics Products.
Note: E-mail support@inovonics.com for a copy of the CE Declaration of
Conformity.
ATransmit LED BActivation
buttons
CFrequency band
selection pins
D EReset button Battery
C
B
AD
E


Produkt Specifikationer

Mærke: Inovonics
Kategori: Controller
Model: EchoStream EN1223D

Har du brug for hjælp?

Hvis du har brug for hjælp til Inovonics EchoStream EN1223D stil et spørgsmål nedenfor, og andre brugere vil svare dig




Controller Inovonics Manualer

Controller Manualer

Nyeste Controller Manualer