Inovonics EchoStream EN1223S Manual

Inovonics Joystick EchoStream EN1223S

Læs nedenfor 📖 manual på dansk for Inovonics EchoStream EN1223S (1 sider) i kategorien Joystick. Denne guide var nyttig for 37 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
© Inovonics, 2009 - www.inovonics.com
EN1223S EchoStream® Water-Resistant
Single-Button Pendant Transmitter
Installation and Operation Manual - 05582A
1 Overview
The Inovonics EN1223S pendant transmitter is our smallest, lightest, and
most versatile pendant.
1.1 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics Wireless
technical services:
E-mail: support@inovonics.com
Phone: (800) 782-2709
1.2 Transmitter Components
Figure 1 Transmitter components
2 Installation and Startup
2.1 Installation Notes
These products are designed to be maintained by professional
security technicians.
Products are intended for indoor use.
Manually test all products weekly.
2.2 Install/Replace the Battery
1. If present, remove the 3 three housing screws on the back of the
transmitter.
2. Open the housing.
3. Install the new battery, ensuring the positive terminals (+) face the
indicated side of the holder.
4. Allow 30 seconds for the capacitor to charge and then press Reset.
Note: When the battery is removed the transmitter may continue to operate
or report a low battery until all energy is discharged from the capacitor.
2.3 Select the Frequency Band
EchoStream products are able to use a range of radio frequencies, and
must be configured for your geographic area. To configure the transmitter:
1. Place a selection jumper on the appropriate frequency band selection
pins.
Place the jumper on the right two pins, marked NZ, to set the
frequency range to 921-928 MHz for New Zealand.
Place the jumper on the left two pins, marked AU, to set the frequency
range to 915-928 MHz for Australia.
Leave the jumper off the pins to set the frequency range to 902-928
MHz for North America.
2. Press the Reset button to complete conguration.
Caution: When pressing the Reset button, make sure you don’t also touch
the frequency band selection pins. Touching the frequency band selection
pins while pressing the Reset button can inadvertently set the transmitter
to the wrong frequency band.
2.4 Register the Transmitter
The transmitter must be registered with the system in order to be monitored
and supervised. When supervised, the transmitter will send a check-in
message to the serial receiver or network coordinator every three minutes.
Each transmitter has a unique factory-programmed identification number.
Refer to the receiver’s installation instructions for details on registering a
transmitter.
1. When prompted by the receiver to reset transmitter, press the Reset
button.
Caution: The transmitter should be tested after registration to ensure
operation. To test the transmitter, activate each of the conditions and
ensure an appropriate response.
3 Operate the Transmitter
To activate the transmitter, press the button for at least one second. Alarm
signals are transmitted multiple times and are indicated by the blinking
transmission LED. When the buttons are released, the transmitter sends an
alarm restoral signal.To test a transmitter, activate the alarm by pressing
the button(s).
4 Specifications
Dimensions: 5.6 x 4.8 x 1.8 cm (2.2 x 1.9 0.72”)
Operating temperature: 0 to 60°C (32 to 140°F)
Operating environment Water-resistant, non-submersible
Typical battery life: 3-5 years
Battery type (BAT609): Renata CR2450, Panasonic CR2450
Power requirement: 3 VDC, 60 mA
Note: Specifications and data are subject to change without notice.
5 Warranty and Disclaimer
Note: Changes or modifications to this unit not expressly approved by
Inovonics Wireless Corporation may void the installer's authority to operate
the equipment as well as the product warranty.
Inovonics Wireless Corporation ("Inovonics") warrants its products
("Product" or "Products") to conform to its own specifications and to be free
of defects in materials and workmanship under normal use for a period of
thirty-six (36) months from the date of manufacture. Within the warranty
period, Inovonics will repair or replace, at its option, all or any part of the
warranted Product. Inovonics will not be responsible for dismantling and/or
reinstallation charges. To exercise the warranty, the User ("User", "Installer"
or "Consumer") must work directly through their authorized distributor who
will be given a Return Material Authorization ("RMA") number by Inovonics.
Details of shipment will be arranged directly through the authorized
distributor.
This warranty is void in cases of improper installation, misuse, failure to
follow installation and operating instructions, alteration, accident or
tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other warranties,
obligations or liabilities, whether written, oral, express, or implied. There is
no warranty by Inovonics that Inovonics product will be merchantable or fit
for any particular purpose, nor is there any other warranty, expressed or
implied, except as such is expressly set forth herein. In no event shall
Inovonics be liable for an incidental, consequential, indirect, special, or
exemplary damages, including but not limited to loss of profit, revenue, or
contract, loss of use, cost of down time, or interruption of business, nor any
claim made by distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics does not
authorize any person to act on its behalf to modify or extend this warranty.
This warranty will apply only to Inovonics Poducts. Inovonics will not be
liable for any direct, incidental, or consequential damage or loss
whatsoever, caused by the malfunction of Product due to products,
accessories, or attachments of other manufacturers, including batteries,
used in conjunction with Inovonics Products.
ATransmit LED BReset button CFrequency band
selection pins
B
A
C


Produkt Specifikationer

Mærke: Inovonics
Kategori: Joystick
Model: EchoStream EN1223S

Har du brug for hjælp?

Hvis du har brug for hjælp til Inovonics EchoStream EN1223S stil et spørgsmål nedenfor, og andre brugere vil svare dig




Joystick Inovonics Manualer

Joystick Manualer

Nyeste Joystick Manualer