Irox TTX306 Manual

Irox Vejrstation TTX306

Læs nedenfor 📖 manual på dansk for Irox TTX306 (1 sider) i kategorien Vejrstation. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

OPERATING

INSTRUCTIONS

Temperature transmitter

(ENG)

Functions

• Additional temperature transmitter for weather

station EBR606C

• For the wireless transmission of outdoor

temperature and DCF time (433 MHz),

transmission range up to 30 m (free field)

• Also for temperature control of remote rooms, f.e.

children's room, wine-cellar

Getting started

• Place the display unit and the transmitter on a

desk with a distance of approximately 1,5 meter.

Check that no other electronic devices are close.

• Take the display unit into operation according to

the manual of the display unit.

• Open the battery compartment of the transmitter

by pushing inwards the two latches at the bottom

and insert 2 x AA 1,5 V batteries, observing the

correct polarity.

• The LED indicator of the transmitter is blinking

and the transmitter is set to channel 1 by default.

• After the sensor is powered up, it will first

transmit the temperature and then the sensor will

start radio controlled time reception. During the

DCF time reception period (maximum 10

minutes), no weather data will be transmitted.

• After the reception of the radio controlled time

the DCF signal appears permanently on the

display of the weather station.

• Note: DO NOT PRESS ANY KEY during the first

10 minutes learning period or before radio

controlled time is displayed on the receiver. After

both outdoor values and radio controlled time are

displayed you can place your remote sensor

outdoors at the final destination. In case the clock

cannot detect the DCF-signal (example due to

disturbances, transmitting distance, etc.) the time

can be set manually. If the outdoor weather data

is not displayed or if any key is pressed before the

weather station receives the signal, or when

changing the transmitter batteries you will need

to follow the battery installation procedure again.

Please wait minimum 10 seconds before

reinserting the batteries!

Note for Radio Controlled Time DCF:

The time base for the radio controlled time is a

Caesium Atom Clock operated by the Physikalisch

Technische Bundesanstalt Braunschweig which has a

time deviation of less than one second in one million

years. The time is coded and transmitted from

Mainflingen near Frankfurt via frequency signal DCF-77

(77,5 kHz) and has a transmitting range of

approximately 1500 km. Your radio controlled clock

receives this signal and converts it to show the precise

time in summer or wintertime. The quality of the

reception. The quality of the reception depends greatly

on the geographic location. In normal cases, there

should be no receptions problems within a 1500 km

radius around Frankfurt.

Please take note at the following:

• The radio controlled time receiver is built inside

the thermo-sensor. It is recommended to keep

distance to any interfering sources and ferro-

concrete buildings.

• During night-time, the atmospheric disturbances

are usually less severe and reception is possible in

most cases. A single daily reception is adequate to

keep the accuracy deviation below 1 second.

Positioning of the transmitter

• Choose a shady and dry position for the

transmitter. (Direct sunshine falsifies the

measurement and continuous humidity strains the

electronic components needlessly)

• Check the transmission of 433 MHz signal from

the transmitter to the display unit (transmission

range 30 m free field). Within ferro-concrete

rooms (basements, superstructures), the received

signal is naturally weakened.

• If necessary choose another position for

transmitter and/or display unit.

Additional transmitters

• The sensor will automatically transmit

temperature to the display unit on channel 1 after

batteries are inserted.

• For having more than one external transmitter,

select a different channel (1 to 3) for every

transmitter by pressing the "CH" button on the

transmitter while the transmission indication LED

is flashing. Press twice for channel 2 and three

times for channel 3 right after the starting up of

the transmitter. The LED is flashing once for

channel 1, twice for channel 2 and three times for

channel 3.

• Press and hold the "CH" Button on the display unit

for 2 secs. To start initialization manually. The

channel number on the LCD of the display unit

flashes and the new transmitter will be received

automatically.

Battery replacement Fig. 2

• Use alkaline batteries only. Observe correct

polarity. Low batteries should be changed soon to

avoid the damage resulting from a leaking battery.

Batteries contain harmful acids. Wear protective

glasses and gloves when handling with leaked

batteries!

Attention: Please do not dispose of old electronic

devices and used batteries in household waste. To

protect the environment, take them to your retail

store or to appropriate collection sites according to

national or local regulations.

Specifications

Measuring range

Outdoor temperature: -20º C…+60º C

Operating temperature: -10º C…+50º C

Resolution temperature: 0,1º C

Transmission frequency: 433 MHz

Transmission range: max. 30 m

Batteries (included): 2 x 1,5 V AA

Maintenance

• Do not expose the instrument to extreme

temperatures, vibrations or shock.

• Clean it with a soft damp cloth.

Do not use solvents

or scouring agents.

• Avoid placing the instruments near interference

sources/metal frames such as computer or TV sets.

• Please reset the unit and follow the battery

installation procedure if the unit does not work

properly. Change the batteries.

Intended usage, exclusion of warranty,

safety information

• The product is not a toy. Keep it out of reacj of

children.

• The product is not to be used for medical purpose

or for public information, but is determined for

home use only.

• The specifications of this product may change

without prior notice.

• Improper use or unauthorized opening of housing

will mean the loss of warranty.

EU DECLARATION OF CONFORMITY

Herewith we declare, that this

wireless transmission device

does comply with the essential

requirements of R&TTE Directive

1999/5/EC

ETS69

Elements Fig. 1

D1: Transmission indication LED

D2: Wall mount hole

D3: Battery compartment holders

D4: "CH" Button

Produkt Specifikationer

Mærke:	Irox
Kategori:	Vejrstation
Model:	TTX306

Har du brug for hjælp?

Hvis du har brug for hjælp til Irox TTX306 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Irox Manualer

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

Vejrstation Manualer

Nyeste Vejrstation Manualer

Conrad WF 50 Manual

8 Marts 2025

La Crosse Technology CA73071 Manual

4 Marts 2025

Marathon Berlin Manual

14 Februar 2025

Marathon Lisbon Manual

14 Februar 2025

TFA 30.5059.02 Manual

5 Februar 2025

Ascot GT-WS-07s Manual

15 Januar 2025

Ventus K0382 Manual

14 Januar 2025

Alecto WS-1200 Manual

12 Januar 2025

TFA 20.1082.17 Manual

12 Januar 2025

Oregon Scientific BAR310HG Manual

12 Januar 2025