JL Audio MBT-CRXv2 Manual


Læs nedenfor 📖 manual på dansk for JL Audio MBT-CRXv2 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Weatherproof Bluetooth® Controller / Receiver
Product Description
The MBT-CRXv2 is a water-resistant (IP67
rated) Bluetooth® receiver designed for
marine and powersports applications. It can
be used as a stand-alone Bluetooth® source
unit/receiver, connecting directly to an
amplifier. It can also be used as an add-on
Bluetooth® controller/receiver, connected
to an existing head unit’s line-level/auxiliary
inputs. The MBT-CRXv2 is not designed to
drive loudspeakers directly.
What’s Included
(1) MBT-CRXv2 Bluetooth
controller/receiver
(1) Threaded fastening collar
(1) Thin round gasket
(1) Thick round gasket
(1) Square adaptor plate
(1) Square adaptor gasket
(4) Stainless steel mounting screws
(1) User Manual
Installation Applications
This product is designed for operation in
12 volt, negative-ground electrical systems.
Using this product in systems with positive
ground and/or voltages other than 12 volts
may result in damage to the product and
will void the warranty. This product is not
certified or approved for use in aircraft.
Safety Considerations
Whenever possible, mount this product
in a dry, well-ventilated location that does
not interfere with other factory installed
electronic devices. If a dry environment is
not available, a location that is not exposed
to heavy splashing may be used.
While this product is designed to be water-
resistant, it should never be submerged
under water for prolonged periods or
subjected to high-pressure water spray.
Do not mount in an engine compartment
or in any areas of extreme heat.
Ensure this product is securely installed so
that it does not come loose in the event of a
collision/sudden jolt or as a result of repeated
vibrations during normal operation.
Check before drilling to make sure that you
will not be drilling into an exterior panel/
hull, fuel tank, gas/brake line, wiring harness,
or other vital system.
Do not run system wiring outside or
underneath the vehicle/vessel. This is an
extremely dangerous practice, which can
result in severe damage/injury.
Protect all system wires from sharp
edges (metal, fiberglass, etc.) by carefully
routing them, tying them down and using
grommets and loom where appropriate.
Secure all wiring as needed, using cable
ties or wire clamps to protect them from
moving parts and sharp edges.
Do not replace the power wire fuse with one
of a different value. Never bypass the fuse.
Mounting & Installation
The design of the MBT-CRXv2 requires just
a single hole for installation. Its easy-to-
use threaded-collar mounting system can
accommodate installations in flat surfaces up
to 1.75 inches (4.5 cm) thick. A front-mounted
adaptor plate is included for installations in
panels exceeding 1.75 inches (4.5 cm) thick,
or where rear access is limited or not possible.
Refer to the diagrams below for your specific
mounting application.
Standard Collar-Mount Installation
Front-Mount Adaptor Installation
IP67
WAT ER
RE SI ST ANT
MBT_CRX_MANv2-071018.indd 1 7/10/18 12:05 PM


Produkt Specifikationer

Mærke: JL Audio
Kategori: Ikke kategoriseret
Model: MBT-CRXv2

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio MBT-CRXv2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret JL Audio Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024