Kicker 50HDS144 Manual


Læs nedenfor 📖 manual på dansk for Kicker 50HDS144 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
50HDS144
Motorcycle Audio Kit Installation Guide for Harley Davidson®
Electra Glide | Street Glide | Ultra Glide | Bat Wing Trikes 2014–
Newer (FLHT)
(1) Wiring Harness
(1) Stainless teel Mounting racket S B (2) PSC652 Kicker peakers S
(4) 8-32 Nylock uts N
(1) Mounting Hardware
(3) 1/4” 20 washers (3) 1/4” 20 1” ts bol
(6) 6” Black able Ties C (1) KPX3004 KICKER mp A
(3) 1/4” Nylock 20 Nuts (2) 8” lack able Ties B C
Important: ver ghtening mounting fasteners ay esult n damage t your motorcycle. lease refer to your servic manual for oper rocedu O -ti m r i o P e pr p res and torque
specifications. ICKER is not esponsibl for age resulting from mproper nstallation echniques. his kit be compatible with some aftermarket K r e dam i i t T may not
head units.
PROGRAMMING O: HD RADI
NOTE: It s ecessar to e i n y r -fl -Da -flash your D adi before nstallatio of his kit. See ocal Harley H r o i n t L vidson ealer have HD adio e D to R r ashed.
1. Remove the eat nd disconnect both egative and ositive battery erminals. s a n p t
2. Remove the windshield.
3. Remov the outer fairing.e
a. Remove the our ounting screws, nplug he headlamp d set sid on a oft loth. f m u t an a e s c
4. Remove th fuel ank.e t
a. Unplug the uel itting the left side of he ank. You ay remove he onsole if you want o retain ent line f f on t t m t c t v routing and onnector c
placement.
b. Remove all four mounting olts n carefully ift the ank ff the ike n set side. b a d l t o b a d a
5. Remove re ddy ver. wi ca co
a. Carefully elease each tab along th caddy ntil it ifts ompletely. r e u l c
SPEAKER INSTALLATION
6. Remove one of the speaker pods from the inner fairing. (Fig. 1)
a. Ther are five fasteners in the center p an three on the outside to release it from innere ortion d the
fairing.
7. Remov stock wit speake from the kit.e the speaker and replace h the PSC652 r
a. Install the speaker into the pod and fasten with the original speaker screws. (Fig. 2)
8. Reinstall the to the inner fairing. pod
9. Repeat for the other side.
AMP TALLATION INS
If you have a 2020 Street r Tri lide, h following teps ust e completed efore amplifier nstallation: o G t e s m b b i
Remove four screws rom the D onnect odule. emove Modul from Bracket. elocate Modul to the clutc sid of h radio nd secure with w 8” zi ties includ f H C M R e R e h e t e a t o p ed. (Fig.
3 and Fig. 4) NOTE: There may be some connectors that will be relocated p off of the radi chassis fo the am o r bracket t fit. o
10. Fasten the amplifier to the bracket with the supplied hardware.
a. Insert the olts hrough the ottom he bracke b t b of t t and nstall he locknuts o i t t the amplifier.
11. At this time, is highly recommended to set the amp gai setting 0. KICKER recommends that the switches b set u as it n to dip e p follows (Fig. 5)
In 0 put Gain ontrol c
Auto urn t -on - 12V
Fader - ON
Input l evel - HI
Amp1: HI-PASS – 80 Hz
Amp2: HI-PASS – 60 Hz 6x9) (   80 Hz 6.5” our Pack) ( T
12. After finishing System Setup, use t supplied ¼” hardware and fasten the amp/bracket assembly to the radio chassis with the 10 connector and power connector he -pin
facing the throttle side. (Fig. 6)
HARNESS INSTALLATION
13. Plug th harness into the amplifier and route the speaker wires to their respective locations. e (Fig. 7)
a. Separate the speaker connectors and plug in the amplifier harness to each speaker.
14. Plu the 4g -pin male, rear audio connector into the 4 audio signal connector comin from the radio harness. -pin femal reare g (Fig. 8 and 9) Fig.
15. Plug the switched power harness th 2 amp connector on the throttle side of the fairing. into e -pin (Fig. 10)
16. Plug the blue wire on kicker harness into the switched power harness lead with one wire. the
a. This allows for an accessory 12V port to remain available.
17. Route the clutch the power leads alon and the rear speaker plug g the side of frame neck, i caddy t th seat area. n the electrical o e (Fig. 11)
18. Reconnect t battery terminals an pull excess he d the harness slack back into th fairing. Create a slack loop with excess harness slack. e
19. Plug t radio he in and set the gain. If not using rear speakers it is recommend to leave the amp 2 gain turned all the way down.
20. Test component function an set t gai optimize system performance. d he n to
21. Carefully r the enjoy your new audi ki eassemble motorcycle and o t!
Note: If you are not using rear speakers you will need to connect the Dummy Plug (fig. 13) to the rear speaker connector under the seat.
For questions, pleas contact KI e CKER -256-080 Technical Support at 800 8, M -F 8 am:00 – 5: pm CST or email at support@kicker.com00
Torx T-27
Package Contents:
(1) Install Guide
(4) 8-32 x /2” utt Head Bolts 1 B on
Tools Needed: 3/16" Allen wrench
10mm Box end wrench
7/16" Box end wrench or socket
Torx T-40
Note: At this time it is highly recommended to cover the dip swtiches with the included mylar cover as seen in (Fig. 12)
(1) Mylar cover ( ) Dummy Plug1


Produkt Specifikationer

Mærke: Kicker
Kategori: Ikke kategoriseret
Model: 50HDS144

Har du brug for hjælp?

Hvis du har brug for hjælp til Kicker 50HDS144 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Kicker Manualer

Kicker

Kicker 50HDS962 Manual

2 September 2024
Kicker

Kicker 50HDR154 Manual

2 September 2024
Kicker

Kicker 50HDS144 Manual

2 September 2024
Kicker

Kicker SF150SC15 Manual

22 Februar 2024
Kicker

Kicker KMLC Manual

28 Oktober 2022

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer