Leviton SGVSM-W Manual

Leviton Controller SGVSM-W

Læs nedenfor 📖 manual på dansk for Leviton SGVSM-W (2 sider) i kategorien Controller. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Strauss™ Volume Control
200 Watts (100 RMS)
Cat. No. SGVSM
DI-000-SGVSM-00A
INSTALLATION
WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND
REGULATIONS.
WARNING: MAXIMUM AMPLIFIER POWER IS 100 WATTS PER CHANNEL. HIGHER AMPLIFIER POWER MAY
CAUSE DAMAGE.
Before starting connections, please note that the left and right attenuator circuits are completely isolated from each other
to prevent instability when used with certain types of amplifiers which have floating grounds. If the amplifier to be used
has common grounds between channels, a 3 wire system can be used between the amplifier and control, but it will be
necessary to connect a jumper between the control ground returns (L- & R-).
If one ground is open, there will be no output on the ungrounded channel at any attenuator setting.
The connectors on the attenuator are the screw-to-tighten type. Connect wires per WIRING DIAGRAM as follows:
1. Select location for mounting control.
NOTE: Due to the depth of volume control, a low-voltage ring or deep electrical box is recommended.
2. Make connections by stripping wire insulation back about 1/4” (.63 cm). Twist any loose strands tightly.
NOTE: It is recommended that at least 16 AWG speaker wire be used for runs up to 30’ (9.1 m). For runs longer than
30’ (9.1 m), use 14-18 AWG wire.
3. Insert the wires from the amplifier into the “TO AMP” openings of the connector, Positive-to-Positive and Negative-to-
Negative, then tighten screws. Check for stray wire strands that might cause a short circuit. Make sure the metal part of
the screw connector engages the bare wire, NOT the insulation!
4. Similarly, connect speaker wires to the “TO SPEAKER” openings and tighten screws.
IMPEDANCE NOTE: There are two impedance settings. 2x is used for up to four rooms connected to a single 8 ohm
rated amplifier output and 6x which is used for 5 to six rooms.
5. ensuring that terminal connector is at top. Install control in its operating location,
NOTE: Leave control 3 or 4 positions above minimum volume before starting the system for the first time to avoid
damaging the speakers, while still being loud enough to observe operation.
INSTALLATION MANUAL
DI-000-SGVSM-00A
SPECIFICATIONS
Attenuator Type: Ceramic Resistive Network
Switch: 12 position slider, make-before-break contacts, low torque specifications for smooth feel
Connector: Screw-tight type, removable connector block
Amplifier Power Rating: 200 Watts (100 RMS)
Impedance Matching: 2 x 8 Ohms
(provided by jumpers) 6 x 47 Ohms
Frequency Response: 20-20kHz +/- 1db, 4-16 Ohm load
Attenuation: 36db

Produkt Specifikationer

Mærke: Leviton
Kategori: Controller
Model: SGVSM-W

Har du brug for hjælp?

Hvis du har brug for hjælp til Leviton SGVSM-W stil et spørgsmål nedenfor, og andre brugere vil svare dig


Controller Leviton Manualer

Leviton

Leviton MC7008 Manual

20 August 2024
Leviton

Leviton SGVSM-W Manual

18 August 2024

Controller Manualer

Nyeste Controller Manualer

Speed-Link

Speed-Link Thunderstrike Manual

12 December 2024
IVT

IVT SCDplus Manual

11 December 2024
Alfatron

Alfatron ALF-IPCON-HDMI Manual

10 December 2024
GVM

GVM YK22 Manual

10 December 2024
Hotone

Hotone Ampero Control Manual

7 December 2024
Hotone

Hotone Patch Kommander Manual

7 December 2024
Thrustmaster

Thrustmaster Ferrari GT Experience Manual

13 Oktober 2024
Thrustmaster

Thrustmaster T3PA Add-On Gaming Pedal Set Manual

5 Oktober 2024
Hori

Hori Battle Pad Manual

4 Oktober 2024
Razer

Razer Wolverine V3 Pro Manual

3 Oktober 2024