Micro Connect MC-GEN-270 Manual

Micro Connect Skifte MC-GEN-270

Læs nedenfor 📖 manual på dansk for Micro Connect MC-GEN-270 (1 sider) i kategorien Skifte. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/1
INTRODUCTION:
2 Way Speaker Switch
with Banana Connector
The product is used to distribute loudspeaker output signals from
audio amplifiers to different loudspeakers for selection and control
the volume.
This product is only approved for connection to loudspeaker outputs
of audio amplifiers and inputs of passive loudspeakers.
CONNECTION:
OPERATION:
SPECIFICATIONS:
PACKAGE CONTENTS:
● Main unit x1
● User Manual x1
1) Connect only loudspeaker outputs of audio amplifiers to the loudspeaker terminals AMP INPUT.
2) Connect only passive loudspeakers with impedance between 4 and 8 ohms to the loudspeaker terminals
SPEAKER OUTPUT.
3) Use only suitable speaker cables with a maximum cross-section of 6 mm² for cabling.
4) Carefully check the relevant operating instructions of the devices that are to be connected in regards to input and
output wiring.
5) If these instructions are not observed, the device or connected devices (amplifier or loudspeaker) may get
damaged.
6) Switch off the power switch of the amplifier before connecting it and do not switch the amplifier on again until you
have made all the necessary connections and che¬cked them. Proceed in the same way when changing the
circuit.
7) Make sure to introduce neatly the stranded wires into loudspeaker terminals to ex¬clude short circuits. Do not
remove more than 6 mm of insulation from the speaker line.
● Note the identification for connecting the loudspeaker terminals:
red = positive terminal
black = negative terminal
RIGHT = right terminal
LEFT = left terminal
● Connect loudspeaker terminals SPEAKER OUTPUT PAIR 1 and PAIR 2 to the speakers.
● Connect loudspeaker terminals AMP INPUT to the loudspeaker outputs of the amplifier.
Loudspeakers connected can be switched on individually or at the same time using the SPEAKERS selectors.
Speaker pair 1 is still running when both SPEAKERS selectors are in the OFF posi¬tion. This circuit protects your
amplifier against damage during idle operation.
● Turn on your amplifier and start the music programme you want.
● Use the SPEAKERS selectors to select the desired loudspeaker pair (PAIR 1 or PAIR 2).
Position ON > Loudspeaker pair switched on
Position OFF > Loudspeaker pair switched off
● The SPEAKER PAIR 2 VOLUME controller is used to adjust the volume of speaker pair 2.
● The overall volume is adjusted with the volume control on the amplifier.
Load.............................................. 60 W per channel
Impedance................................... 4 – 16 Ω
Cable length................................. max. 50 m
Wire cross section........................ max. 2.5 mm2
Operating conditions.................... -25 to +85 ºC, 20 – 75 % RH
Storage conditions....................... -25 to +85 ºC, 20 – 75 % RH

Produkt Specifikationer

Mærke: Micro Connect
Kategori: Skifte
Model: MC-GEN-270

Har du brug for hjælp?

Hvis du har brug for hjælp til Micro Connect MC-GEN-270 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Skifte Micro Connect Manualer

Micro Connect

Micro Connect MC-GEN-270 Manual

1 September 2024
Micro Connect

Micro Connect MC-HM-MT402H Manual

20 August 2024
Micro Connect

Micro Connect MC-HM-MT404L Manual

19 August 2024

Skifte Manualer

Nyeste Skifte Manualer

Powerfix

Powerfix PSSS 2 A1 Manual

14 Januar 2025
Ebara

Ebara ServoPress LP Manual

14 Januar 2025
D-Link

D-Link DES-1024D Manual

13 Januar 2025
TRENDnet

TRENDnet TEG-S5g Manual

13 Januar 2025
INOGENI

INOGENI CAM230 Manual

13 Januar 2025
Schneider

Schneider CCT15225 Manual

13 Januar 2025
Luxul

Luxul XMS-5248P Manual

13 Januar 2025
Luxul

Luxul AMS-2624P Manual

13 Januar 2025
Luxul

Luxul XGS-1005 Manual

13 Januar 2025
Luxul

Luxul AGS-1008M Manual

13 Januar 2025