Milwaukee 2116-21 Manual

Milwaukee Lommelygte 2116-21

Læs nedenfor 📖 manual på dansk for Milwaukee 2116-21 (2 sider) i kategorien Lommelygte. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

IMPORTANT SAFETY INSTRUCTIONS

WARNING

READ AND UNDERSTAND ALL INSTRUC-

TIONS. Failure to follow all instructions listed be-

low, may result in electric shock, re and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS - THIS MANUAL CONTAINS IM-

PORTANT SAFETY AND OPERATING INSTRUCTIONS FOR THE

REDLITHIUM® USB BATTERY AND USB RECHARGEABLE LIGHT.

2. USE AND CHARGE ONLY REDLITHIUM® USB BATTERIES IN THIS

USB RECHARGEABLE LIGHT. OTHER TYPES OF BATTERIES MAY

CAUSE PERSONAL INJURY AND DAMAGE.

3. BEFORE USING THE BATTERY AND LIGHT, READ THIS OPERA-

TOR’S MANUAL AND ALL LABELS ON THE BATTERY AND LIGHT.

4. USE ONLY WITH LISTED/CERTIFIED ITE POWER SUPPLY. Others

may result in a risk of re, electric shock or personal injury.

5. AVOID DANGEROUS ENVIRONMENTS. Do not charge battery in rain, snow,

damp or wet locations. Do not use battery or charger in the presence of explosive

atmospheres (gaseous fumes, dust or ammable materials) because sparks

may be generated when inserting or removing battery, possibly causing re.

6. CHARGE IN A WELL VENTILATED AREA. Do not block charger vents.

Keep them clear to allow proper ventilation. Do not allow smoking or open

ames near a charging battery. Vented gases may explode.

7. MAINTAIN CORD. When unplugging charger, pull plug rather than cord

to reduce the risk of damage to the electrical plug and cord. Never carry

charger by its cord. Keep cord from heat, oil and sharp edges. Make sure

cord will not be stepped on, tripped over or subjected to damage or stress.

Do not use charger with damaged cord or plug. Have a damaged charger

replaced immediately.

8. USE ONLY RECOMMENDED ATTACHMENTS. Use of an attachment not

recommended or sold by the battery charger or battery manufacturer may

result in a risk of re, electric shock or personal injury.

9. TO REDUCE THE RISK OF ELECTRIC SHOCK, always unplug charger

before cleaning or maintenance.

10. DO NOT BURN OR INCINERATE BATTERY PACKS. Battery may explode,

causing personal injury or damage. Toxic fumes and materials are created

when battery are burned.

11. DO NOT CRUSH, DROP, OR DAMAGE battery. Do not use a battery or

charger that has received a sharp blow, been dropped, run over, or dam-

aged in any way (e.g., pierced with a nail, hit with a hammer, stepped on).

12. DO NOT DISASSEMBLE. Incorrect reassembly may result in the risk of

electric shock, re or exposure to battery chemicals. If it is damaged, take

it to a MILWAUKEE service facility.

13. BATTERY CHEMICALS CAUSE SERIOUS BURNS. Never allow contact

with skin, eyes, or mouth. If a damaged battery leaks battery chemicals,

use rubber or neoprene gloves to dispose of it. If skin is exposed to battery

uids, wash with soap and water and rinse with vinegar. If eyes are exposed

to battery chemicals, immediately ush with water for 20 minutes and seek

medical attention. Remove and dispose of contaminated clothing.

14. DO NOT SHORT CIRCUIT. A short-circuited battery pack may cause re,

personal injury, and product damage. A battery pack will short circuit if

a metal object makes a connection between the positive and negative

contacts on the battery pack. Do not place a battery pack near anything

that may cause a short circuit, such as coins, keys or nails in your pocket.

15. DO NOT ALLOW FLUIDS TO FLOW INTO BATTERY PACK. Corrosive

or conductive uids, such as seawater, certain industrial chemicals, and

bleach or bleach containing products, etc., can cause a short circuit.

16. STORE in a cool, dry place. Do not store battery where temperatures may

exceed 120°F (50°C) such as in direct sunlight, a vehicle or metal building

during the summer.

17. TO REDUCE THE RISK OF INJURY, CLOSE SUPERVISION IS NEC-

ESSARY when an appliance is used near children.

18. STORE IDLE LIGHT OUT OF REACH OF CHILDREN. Warm lights can

become hazardous in the hands of children.

19. KNOW YOUR LIGHT. Read this manual carefully to learn your light's

applications and limitations as well as potential hazards associated with

this type of light.

20. MAINTAIN LABELS AND NAMEPLATES. -These carry important infor

mation. If unreadable or missing, contact a MILWAUKEE service facility for

a free replacement.

INSTRUCTIONS FOR

INSTRUCTIONS FOR INSTRUCTIONS FOR

FUTURE REFERENCE.

FUTURE REFERENCE.FUTURE REFERENCE.

SPECIFICATIONS

Cat. No. 2116-20 ..................................................................................

USB Input Volts ............................................................................5 DC

USB Input Amps ...................................................................0.1 - 2.1 A

Output Volts ..................................................................................4 DC

Output Amps ..................................................................................2.1A

REDLITHIUM® USB Batteries

Volts ..............................................................................................4 DC

Operating Temperature

Battery and Charger ..............................

40°F to 104°F (4°C to 40°C)

Battery and Tool ....................................0

°F to 140°F (-18°C to 60°C)

Power Supply Cat. No. 44-66-1202 .......................................................

SYMBOLOGY

Volts

Direct Current

Amps

Do not stare at the

operating light source

Read Operator's

Manual

Properly Recycle

Batteries

BFP Backfeed Protected

California Energy

Commission

BATTERY

WARNING

To reduce the risk of re, personal injury, and prod-

uct damage due to a short circuit, never immerse

your tool, battery pack or charger in uid or allow a uid to ow

inside them. Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach containing

products, etc., can cause a short circuit.

Maintenance and Storage

Do not expose your battery or cordless tools to water or rain, or allow

them to get wet. This could damage the tool and battery. Do not use

oil or solvents to clean or lubricate your battery. The plastic casing will

become brittle and crack, causing a risk of injury.

Store batteries at room temperature away from moisture. Do not store

in damp locations where corrosion of terminals may occur. As with other

battery types, permanent capacity loss can result if the pack is stored for

long periods of time at high temperatures (over 120° F). MILWAUKEE

Li-Ion batteries maintain their charge during storage longer than other

battery types. After about a year of storage, charge the battery as normal.

WARNING

To reduce the risk of injury or explosion, never burn

or incinerate a battery pack even if it is damaged,

dead or completely discharged. When burned, toxic fumes and

materials are created.

Disposing of MILWAUKEE Li-Ion Battery

MILWAUKEE Li-Ion batteries are more environmentally friendly than

some other types of power tool batteries. Always dispose of your battery

according to federal, state and local regulations. Contact a recycling

agency in your area for recycling locations.

Even discharged batteries contain some energy. Before disposing, use

electrical tape to cover the terminals to prevent the battery from shorting,

which could cause a re or explosion.

RBRC Battery Recycling Seals

The RBRC™ Battery Recycling Seals (see "Symbology") on your bat-

teries indicate that MILWAUKEE has arranged for the recycling of that

battery with the Rechargeable Battery Recycling Corporation (RBRC). At

the end of your battery's useful life, return the battery to a MILWAUKEE

Branch O󰀩ce/Service Center or the participating retailer nearest you.

For more information, visit the RBRC web site at www.rbrc.org.

USB RECHARGEABLE BEACON™ HARD HAT LIGHT

LUMIÈRE DE BEACON™ DE RECHARGEABLE DE USB POUR CASQUE DE PROTECTION

LUZ DEL CASCO BEACON™ RECARGABLE CON USB

USB RECHARGEABLE LIGHT

WARNING

Use and charge only REDLITHIUM® USB batteries in

this USB rechargeable light. Other types of batteries

may cause personal injury and damage.

Inserting the Battery

1. Open the battery door.

2. Line up the battery with the compartment and fully insert the battery.

3. Close the battery door.

Charging the Battery

1. Plug your USB cable into a power source such as an AC wall adaptor,

computer or car port.

2. Lift the rubber cover to expose the micro USB port. Insert the micro

USB plug into the micro USB port. Users may experience longer

charge times from laptops and other power sources.

3. The indicator light will display the charging status:

Red Solid: Charging, 0-79% charged

Green Flashing: Charging, 80-99% charged

Green Solid: 100% Charged

Red/Green Flashing: Damaged or Faulty Battery

If the light indicator ashes red and green, check that the battery is fully

seated into the bay. Remove the battery and reinsert. If the light con-

tinues to ash red and green, the battery may be extremely hot or cold,

or wet. Allow the battery to cool down, warm up, or dry out and then

reinsert. If the problem persists, contact a MILWAUKEE service facility.

Operation

CAUTION

To reduce the risk of injury, do not stare at the oper-

ating light source.

Headlamp

Clip the light onto the strap and use the buckle to adjust the strap to the

required size. Use the included clips to attach to a hard hat. Rotate the

light up or down as needed.

Press the power button to turn the light on and o󰀨.

Press the mode button to cycle through Spot/Flood, Flood High, Flood

Medium, Flood Low, and Spot.

The fuel gauge will display the battery life:

Green Solid: 50-100% remaining

Yellow Solid: 1-49% remaining

Red Solid: 3-10% remaining

Red Flashing: 0-3% remaining

During use, when the battery charge reaches 3%, the main LED and

charge indicator will ash, indicating up to 5 minutes of runtime remains.

Prior to immediate shutdown, the main LED will ash 3 times, then the

tool will shutdown. Remaining runtime may be less than 5 minutes if the

light is turned on when battery capacity is already 0-3%.

BEACON™ Light

Press the power button to cycle through on, strobe and o󰀨. Press

and hold the power button to turn o󰀨 without cycling.

WARNING

To reduce the risk of injury, always unplug the

charger and remove the battery from the charger

before performing any maintenance. The charger and battery

have no internal serviceable parts. Never disassemble the battery

or charger.

Maintenance and Storage

Store your charger in a cool, dry place.

As a general practice, it is best to unplug battery chargers and remove

batteries when not in use. No battery damage will occur, however, if the

charger and battery are left plugged in.

WARNING

To reduce the risk of injury and damage, never im-

merse your battery or charger in liquid or allow a

liquid to ow inside them.

Cleaning

Clean out dust and debris from charger vents and electrical contacts

by blowing with compressed air. Use only mild soap and a damp cloth

to clean the battery and charger, keeping away from all electrical

contacts. Certain cleaning agents and solvents are harmful to plastics

and other insulated parts. Some of these include gasoline, turpentine,

lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia

and household detergents containing ammonia. Never use ammable

or combustible solvents around batteries, charger, or tools.

SERVICE - UNITED STATES

1-800-SAWDUST (1.800.729.3878)

Monday-Friday, 7:00 AM - 6:30 PM CST

or visit www.milwaukeetool.com

Contact Corporate After Sales Service Technical Support with technical,

service/repair, or warranty questions.

Email: metproductsupport@milwaukeetool.com

Become a Heavy Duty Club Member at www.milwaukeetool.com to

receive important notications regarding your tool purchases.

SERVICE - CANADA

Milwaukee Tool (Canada) Ltd

1.800.268.4015

Monday-Friday, 7:00 AM - 4:30 PM CST or visit www.milwaukeetool.ca

LIMITED WARRANTY - USA & CANADA

Every MILWAUKEE REDLITHIUM USB battery and charger* is warranted to the original purchaser only to be free

from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace repair

a REDLITHIUM USB battery or charger which, after examination, is determined by MILWAUKEE to be defective in

material or workmanship for a period of two (2) years after the date of purchase unless otherwise noted. Return of the

REDLITHIUM USB battery or charger to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized

Service Station, freight prepaid and insured, is required. For the proper shipping procedure of battery packs, contact

1.800.SAWDUST (1.800.729.3878), or go to www.milwaukeetool.com. A copy of the proof of purchase should be

included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from

repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse,

normal wear and tear, lack of maintenance, or accidents.

Normal Wear: This warranty does not cover repair or replacement when normal use has exhausted the life of a part

including, but not limited to charging cables, and wall plugs.

*This warranty does not cover any cordless product sold with the REDLITHIUM USB battery and/or charger. There

are separate and distinct warranties available for these products.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A

CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT

AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAU-

KEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY

COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY

DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS

FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.

TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING

WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR-

RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED

ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO

THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the Find a Service Center Search in the Parts & Service section of MILWAUKEE’s website www.milwaukee-

tool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest MILWAUKEE factory Service Center location.

LIMITED WARRANTY - USA & CANADA

Every MILWAUKEE Personal Lighting Product* (see exceptions below) is warranted to the original purchaser only to be

free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace any

part on a personal lighting product which, after examination, is determined by MILWAUKEE to be defective in material or

workmanship for the lifetime of the personal lighting product. Return of the personal lighting product to a MILWAUKEE

factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A

copy of the proof of purchase should be included with the return product. This warranty does not apply to damage that

MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized person-

nel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, accidents, or caused by alkaline batteries.

Normal Wear: This warranty does not cover repair or replacement when normal use has exhausted the life of a part

including, but not limited to clips, straps, charging cables, wall plugs, and rubber gaskets. This warranty does cover the

LED in the personal lighting products, subject to the limitations herein.

*This warranty does not cover Cordless Battery Packs or Chargers. There are separate and distinct warranties available

for these products.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION

OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS

CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR

ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES,

EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR

DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,

SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND

IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW,

MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER

IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE

EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the Find a Service Center Search in the Parts & Service section of MILWAUKEE’s website

www.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest MILWAUKEE factory Service Center location.

INSTRUCTIONS DE SÉCURITÉ

IMPORTANTES

AVERTISSEMENT

LIRE ET COM PRENDRE TOUTES LES

INSTRUCTIONS. Le non-respect des in-

structions ci-après peut entraîner des chocs électriques, des incendies

et/ou des blessures graves.

CONSERVER CES INSTRUCTIONS

1. GARDEZ CES INSTRUCTIONS – CE MANUEL CONTIENT DES INSTRUC-

TIONS D’OPÉRATION ET SÉCURITÉ IMPORTANTES À PROPOS DE LA

PILE RECHARGEABLE PAR USB REDLITHIUM® AINSI QUE LA LAMPE

RECHARGEABLE PAR USB.

2. N’UTILISEZ NI NE CHARGEZ QUE LES PILES RECHARGEABLES PAR

USB REDLITHIUM® DANS CETTE LAMPE DE POCHE RECHARGEABLE

PAR USB. D’AUTRES TYPES DE PILES POURRONT ENTRAÎNER DES

BLESSURES ET DOMMAGES.

3. AVANT D’UTILISER LA PILE ET LA LAMPE DE POCHE, LISEZ CE MANUEL

DE L’OPERATEUR AINSI QUE TOUTES LES ÉTIQUETTES QUI SE TROU-

VERONT SUR LA LAMPE DE POCHE ET LA PILE.

4. N’UTILISEZ QUE D’ALIMENTATION ELECTRIQUE LISTEE/CERTIFIE TI.

D’autres pourront entraîner des risques d’incendie, chocs électriques ou blessures.

5. ÉVITEZ DES MILIEUX DANGEREUX. Ne chargez pas la pile dans des milieux

ayant de la pluie, neige, humidité ni d’environnements mouillés. N’utilisez pas la

pile ni le chargeur dans des atmosphères explosives (ayant des vapeurs gazeux,

poudre ou matériel inflammable) parce que des étincelles pourront être créées

lorsque la pile est insérée ou retirée, pouvant bien provoquer des incendies.

6. CHARGEZ-LA DANS UN ESPACE BIEN AÉRÉ. Ne bloquez pas les bouches

du chargeur. Préservez-las propres pour assurer une bonne aération. Ne lais-

sez pas de fumes ni flames décontrôlées près d’une pile du chargeur. Les gaz

aérés pourront exploser.

7. PRÉSERVEZ LE FIL. Lorsque le chargeur est débranché, tirez de la fiche en

lieu du fil afin de réduire les risques de dommages sur tous les deux. Ne portez

jamais le chargeur par son fil. Ne laissez pas que le fil soit exposé à chaleur,

huile ni aux bords tranchants. Assurez-vous de laisser le fils dans un endroit

où il ne pourra pas être marché, trébuché ou endommagé ni sous contrainte.

N’utilisez pas le chargeur avec une fiche ou un fil endommagés. Demandez que

le chargeur endommagé soit remplacé immédiatement.

8. N’UTILISEZ QUE LES ACCESSOIRES RECOMMANDÉS. L’utilisation d’un ac-

cessoire que ne soit pas recommandé ou vendu par le fabriquant de la pile ou le

chargeur pourra entraîner des risques d’incendies, chocs électriques ou blessures.

9. AFIN DE RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, débranchez toujours

le chargeur avant de le nettoyer ou l’entretenir.

10. NE BRÛLEZ PAS NI N’INCINÉREZ PAS LES BLOC-PILES. La pile pourra

exploser, en entraînant des dommages ou blessures. Des vapeurs ou matériaux

toxiques sont créés lorsque la pile est brûlée.

11. N’ÉCRASEZ PAS la pile, NE LA LAISSEZ PAS TOMBER NI NE

L’ENDOMMAGEZ PAS. N’utilisez pas une pile ni un chargeur qui ait reçoit un

coup sec, été marché, écrasé ou endommagés de n’importe quelle forme (par

exemple, percé par un clou, frappé par un marteau, marché).

12. NE LE DÉSASSEMBLEZ PAS. Le démantèlement incorrect peut entraîner un

risque de chocs électriques, incendie ou exposition à produits chimiques. Si

l’outil est endommagé, amenez-le au centre de service MILWAUKEE.

13. LES PRODUITS CHIMIQUES ENTRAÎNENT DES BRÛLURES GRAVES. Ne

permettez pas qu’ils entrent en contact avec la peau, les yeux ni la bouche. Si

de la pile endommagée des produits chimiques se coulent, utilisez des gants

en caoutchouc ou néoprène pour se débarrasser d’elle. Si la peau est exposée

à des fluides de la pile, lavez-la avec du savon et de l’eau et rincez-la avec du

vinaigre. Si les yeux sont exposés aux produits chimiques de la pile, lavez-les

avec pleine de l’eau pendant 20 minutes et consultez un médecin. Retirez les

vêtements contaminés et se débarrassez d’eux.

14. NE PAS COURT-CIRCUITER. Un bloc-piles court-circuité pourra mener un

incendie, des blessures physiques et endommager le produit. Un bloc-piles

court-circuitera si un objet métallique établit une connexion entre les contacts

positif et négatif du bloc-piles. Mettre le bloc-piles à l’écart de tout ce qui pourra

causer un court-circuit, tel que des pièces de monnaie, des clés ou des clous

dans votre poche.

15. NE PAS LAISSER LES FLUIDES ENTRER DANS LE BLOC-PILES. Les

uides corrosifs et conducteurs, tels que l’eau de mer, quelques produits

chimiques industriels et solutions d’eau de Javel ou d’autres produits ayant de

l’hypochlorite, etc., pourront provoquer des courts-circuits.

16. L’ENTREPOSEZ dans un endroit sec et bien aéré. Ne mettez la pile où les

températures pourront surpasser les 50 ºC (120 ºF), tels que la lumière du soleil,

un véhicule ou un bâtiment en acier en été.

17. AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, SUPERVISION

ÉTROITE EST REQUISE quand un appareil est utilisé près d’enfants.

18. TENEZ L’INDICATEUR DE REPOS HORS DE LA PORTÉE DES ENFANTS.

Des lumières chaudes peuvent être dangereuses dans la portée des enfants.

19. CONNAISSEZ VOTRE LAMPE. Lisez attentivement ce manuel de l’opérateur

pour savoir à propos des applications et limitations de la lampe ainsi que les

dangers possibles liés à ce type de lampe.

20. PRÉSERVEZ LES ÉTIQUETTES ET PLAQUES NOMINATIVES. Elles

montrent d’information importante. Si elle est illisible ou manquante, contactez

un centre de service MILWAUKEE afin de recevoir un outil substitutif gratuit.

LIRE ET CONSERVER

TOUTES LES INSTRUCTIONS

POUR RÉFÉRENCE FUTURE.

SPÉCIFICATIONS

No de Cat.. 2116-20 .............................................................................

Voltage d’entrée par USB ............................................................5 CD

Ampérage d’entrée par USB ............................................... 0,1 - 2,1 A

Voltage de sorti ............................................................................4 CD

Ampérage de sorti .........................................................................2,1A

REDLITHIUM® Bloc-piles USB

Voltage.......................................................................................... 4 CD

Température opérative

Pile et chargeur ....................................

4°C to 40°C (40°F to 104°F)

Pile et outil ............................................

-18°C to 60°C (

°F to 140°F)

No de Cat. de la prise d’alimentation ............................... 44-66-1202

PICTOGRAPHIE

Volts

Courant direct

Ampères

Ne pas regarder

la source de lumière

de fonctionnement

Lisez le manuel

de l’operateur

Recyclage correct

des batteries

BFP Rétro-alimentation protégée

Commission à l'Énergie de

la Californie

BLOC-PILES

AVERTISSEMENT

Pour réduire le risque d’incendie, de bles-

sures corporelles et de dommages causés

par un court-circuit, ne jamais immerger l’outil, le bloc-piles ou le

chargeur dans un liquide ou laisser couler un uide à l’intérieur de

celui-ci. Les uides corrosifs ou conducteurs, tels que l’eau de mer,

certains produits chimiques industriels, les produits de blanchiment

ou de blanchiment, etc., peuvent provoquer un court-circuit.

Entretien et entreposage

Ne pas exposer votre bloc-piles ni vos outils sans l à l’eau ou la pluie,

ou les laisser prendre l'humidité. Cela pourrait endommager l’outil et le

bloc-piles. Ne pas utiliser d'huile ou solvants pour nettoyer ou lubrier

votre bloc-piles. Le boîtier du bloc-piles risque de devenir cassant ou

de se fendiller, causant un risque de blessure.

Entreposer les blocs-piles à température ambiante à l'abri de l’humidité.

Ne pas les entreposer dans un endroit humide où la corrosion des

bornes peut survenir. Comme pour d'autres types de batteries, une

perte permanente de capacité peut survenir si le bloc-piles est entre-

posé pendant longtemps à haute température (48°C/120°F). Les piles

Li-ion MILWAUKEE maintiennent leur charge pendant plus longtemps

que les autres types de piles. Après un an d'entreposage, rechargez le

bloc-piles comme d’habitude.

AVERTISSEMENT

Pour réduire le risque d'explosion, ne jamais

brûler un bloc-piles, même s'il est endom-

magé ou complètement déchargé. Lorsqu’il est brûlé, des matières

et vapeurs toxiques sont produites

MILWAUKEE TOOL

13135 West Lisbon Road ● Brookeld, Wisconsin, U.S.A. 53005

58222116d2 05/20 01670400601Q-01(A) Printed in China

Produkt Specifikationer

Mærke:	Milwaukee
Kategori:	Lommelygte
Model:	2116-21

Har du brug for hjælp?

Hvis du har brug for hjælp til Milwaukee 2116-21 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lommelygte Milwaukee Manualer

Milwaukee L4 FL2000 Manual

2 September 2024

Milwaukee L4 NL400 Manual

2 September 2024

Milwaukee L4 SL550 Manual

2 September 2024

Milwaukee L4 BOLTHL Manual

2 September 2024

Milwaukee L4 HL2 Manual

2 September 2024

Milwaukee L4 FL Manual

2 September 2024

Milwaukee L4 HSL Manual

2 September 2024

Milwaukee HL2-LED Manual

2 September 2024

Milwaukee L4 FFL Manual

2 September 2024

Milwaukee 2161-21 Manual

2 September 2024

Lommelygte Manualer

Nyeste Lommelygte Manualer

Nedis LHLR05WBK Manual

14 Januar 2025

Nedis LHLR10WBK Manual

14 Januar 2025

Coast HP4 Manual

3 Januar 2025

Ledlenser iH8R Manual

31 December 2025

Olight RN 400 Manual

31 December 2025

Nitecore MT21C Manual

29 December 2024

Nitecore Thumb Manual

29 December 2024

Nitecore GEM10 Manual

29 December 2024

Nitecore EC4GTS Manual

29 December 2024

Nitecore MT42 Manual

29 December 2024