My Wall HL 41 ML Manual


Læs nedenfor 📖 manual på dansk for My Wall HL 41 ML (2 sider) i kategorien Projektor tilbehør. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Upward Movement
Press the button, the TV mount will
move upward to the lowest-prole
position against the ceiling. Press the
OK button to stop the motion.
(Tips: Clear up all obstacles
within the range of motion.)
Memory Setting 1
Press the button for 1 second and you will hear a
beep, indicating that the current position
has been saved to memory.
Recall Memory
Press the button and the mount will
automatically get to the position saved
in the corresponding button .mem1
Recall Memory
Press the button and the mount will automa-
tically get to the
position saved in the corresponding button
mem2.
Memory Setting 2
Press the button for 1 seconds and
you will hear a beep, indicating that
the current position has been saved
to memory.
Downward Movement
Press the button, the TV mount will move
downward to the maximum tilt angle position (75° by
default). Press the button to stop the motion. OK
(Tips: Clear up all obstacles within the range of motion.)
: Stop Button
OK
Manual mode
In any positlon (but the minimum position against the ceiling): when manually push up the TV ceiling mount over a distance,
the TV ceiling mount will automatically return back to the minimum position against the ceiling.
Never operate the unit without a TV installed!
Before power connection, be sure that bracket and the TV installed correctly.
Keep the children away from power.
!
RMT-02 AAA battery remote control, 2x (not included)
HL 41 ML / HL 41 MWL
Reset the Tilt Range for Pitched Ceiling
The TV mount is 0° - 75° tilt adjustable by default for at ceiling. Please reset the tilt range if you use as a pitched ceiling TV mount.
Step 1: Reset the system (Instructions on Reset Mode)
Step 2: Press Downward Movement Upward Movement, and buttons and adjust to the proper position.OK
Step 3: Press and hold the Memory Setting 1 button until the unit beeps once. Repeat this step 5 times.
The unit will emit a long beep to indicate success.
Note: Step 2, 3 should be nished in 2 minutes, or it will fail to reset.
Coding of Remote Controller and Control Box
Step 1: When the mount is powered on, press the small button on the control box with a thin tool as shown.
The unit emits a beep, indicating that the control box is on standby for program coding.
Step 2: Press the button on the remote control, and the control box repeatedly beeps for approximate 10 seconds indicating that the SET
remote control is being programmed. The process will be nished automatically until you can‘t hear a beep any longer.
NOTE: The TV Mount can be matched with up to 20 remote controllers. To clean up the data of all the remote controllers, press and
hold the code matching button for 5 seconds then release. The unit will emits two beeps conrm the successful clean up and vice versa.
Reset Mode
If the TV mount can‘t be adjusted to the highest position (0 degree against the ceiling) or the lowest position (max. tilting position),
unplug and re-plug the power. Then press and hold the button for 5 seconds. Mount will retract to the highest position, that OK
means the system has been successfully reset.
Hereby, Transmedia Kabelverbindungen GmbH declares that the suspension brackets type HL 41 ML / HL 41 MWL
is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address: https://www.transmedia-germany.com/download
revised 1
18.01.2022


Produkt Specifikationer

Mærke: My Wall
Kategori: Projektor tilbehør
Model: HL 41 ML

Har du brug for hjælp?

Hvis du har brug for hjælp til My Wall HL 41 ML stil et spørgsmål nedenfor, og andre brugere vil svare dig




Projektor tilbehør My Wall Manualer

My Wall

My Wall HL 41 ML Manual

5 September 2024

Projektor tilbehør Manualer

Nyeste Projektor tilbehør Manualer