Neewer QR Manual

Neewer Ikke kategoriseret QR

Læs nedenfor 📖 manual på dansk for Neewer QR (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

ENEN EN EN

EN EN

Product Overview

Package Contents

01 02 03 04

0605 07 08

QR Receiver ×1

2.5mm to 3.5mm Sync Cable ×1

2.5mm to 2.5mm Sync Cable ×1

6.5mm to 3.5mm Adapter ×1

The QR wireless receiver is designed with the NEEWER 2.4G wireless Q system. Its main

function is to wirelessly transmit the receivied signal in order to trigger on camera ﬂash

speedlites, monolights, outdoor strobe lights, and more using the QPro / Q ﬂash trigger.

Additionally, it can also act as a wireless remote control for camera shutters. The receiver

is available in four versions: universal, Canon, Nikon, and Sony. Please note that there

may be more versions added in the future.

1. Subjecting the device to physical impact or vibrations may result in receiver

malfunction.

2. This product is not waterproof. Immersion in w er or exposure to high humidity at

environments may lead to malfunctions. Rusting of internal components can

cause irreparable damage.

3. Sudden temperature changes, like transitioning between warm and cold

environments, may cause condensation inside the receiver. To prevent

condensation, it is recommended to pack the receiver in a bag or use plastic wrap

before encountering temperature variations.

4. Strong static electricity or magnetic ﬁelds gener ed by devices such as radio at

transmitters can interfere with the normal operation of this product.

Camera Triggering

Cold Shoe

※ Press and hold the <+><-> button simultaneously to restore the factory settings.

LCD Display

Mode Switching

Flash Triggering

Hot Shoe

Cold Shoe Locking Knob

TEST Button

Short press the button to

increase the value in

increments of 1;

Long press to increase

the value rapidly.

Short press the button to

increase the value in

increments of 1;

Long press to increase

the value rapidly.

Status Indic orat

2.5mm Sync Port

Type C USB Firmware

Upgrade Port Power Switch

Battery

Compartment (back)

Group Setting

Battery Level

ID setting

Open the battery compartment cover on

the back of the receiver.

Insert 2 x AA batteries (not included)

respecting the positive and negative

markings in the compartment.

1. Battery Installation

2. Wireless Synchronous Trigger the on-camera ﬂash

Receiver LCD Display

①

②

③

Channel Setting

②

④

Flash trigger Remote Shutter⑤ ⑥

Check the battery level indicator

on the LCD screen. Indic esat

4 Bars Full Power

2 Bars/3 Bars Medium Power

1 Bars Low Battery

Empty indicator Battery almost depleted. Please replace the

battery ASAP

Flashing

Note: For long-term storage, remove the battery to prevent damage or draining.

Low battery warning (Replace the battery

when the power is low to avoid issues such

as ﬂash leakage or failure to ﬂash.)

P er On/Oﬀow

Slide the power switch to the "ON"

position to turn on the device and

to the "OFF" position to turn it oﬀ.

Short press "M" button, when

"CH" is highlighted on screen

in order to set the channel value.

Short press "+" button once, the

channel value will increase in

increments of 1, long press "+"

button to rapidly increase the

channel value shown.

Short press "-" button once in

order to decrease the channel

value in increments of 1; long

press the "-" button to rapidly

decrease the channel value shown.

Channel Setting

Wireless ID Setting

※ The channel value shown will be

increased between the range of available

channels from 01~32. After reaching 32,

it will restart from channel 01.

Product Illustration Product Illustration

Installation Instructions

Using the product

Notes

1. If you are unable to trigger the ﬂash or capture images correctly, please ensure the

following:

a. Check if the batteries are properly installed and the ﬂash trigger's power switch is

turned on.

b. Make sure the ﬂash trigger is set to the same channel as the receiver.

c. Verify that the connection cable or hot shoe is securely and correctly connected.

d. Check if the function mode is set correctly.

2. If the camera can only capture images but cannot focus, please check the following:

Ensure that the camera or lens is not set to MF (manual focus) mode. If it is, switch to

AF (auto focus) mode.

3. If your receiver is experiencing interference from other sources, resulting in ﬂash

misﬁres or issues with capturing images, try changing the channel setting of the

receiver.

4. Reset the QR receiver to its factory settings if the light does not ﬂash when triggered

by the Q Compact.

Troubleshooting and Solutions

10 11 12

Product Model QR

Power Supply 2 x AA Batteries (not included)

Transmission Range

Product Type

>100 meters

Universal Single Contact Receiver

Built-in Wireless 2.4G Frequency

Modulation Mode MSK

Channels 32

Wireless ID OFF; 01-99

Groups A, B, C, D, E (5 groups)

Firmware Update Firmware can be upd ed via the Type-C USB port on the deviceat

Wireless Shutter

Output Interface

Synchronous Flash

Output Interface

Camera shutter can be controlled

through the 2.5mm sync interface

Speciﬁcations

EN EN ENEN

99 A

ID GR

①

03 A

CH GR

③

②

①

③

⑥

④

⑤

03 A

CH G R

Short press "M" button, when "GR"

is highlighted on the screen in

order to set the group value.

Short press "+" button once, the

channel value will increase in

increments of 1, long press "+"

button to rapidly increase the

channel value shown.

Short press "-" button once in

order to decrease the channel

value in increments of 1; long

press the "-" button to rapidly

decrease the channel value shown.

Group Setting

※ The group value will increase sequentially

from A to E. Continued adjustment beyond

group value E will restart from group value A.

②

①

③

Short press "M" button, when the

screen "ID" is highlighted, you can

set the ID value.

Short press "+" button once, the

channel ID value will increase in

increments of 1, long press "+"

button to rapidly increase the

channel ID value shown.

Short press "-" button once in

order to decrease the channel ID

value in increments of 1; long press

the "-" button to rapidly decrease

the channel ID value shown.

②

①

③

03 A

CH G R

23 A

I D GR

Sync Interface Deﬁnition

Long press the "M" button, and the

screen will display " " and " "

icons, allowing you to set the

synchronization interface.

Short press the "+"/"-" button to select

the " " for ﬂash triggering or " " for

remote shutter function.

Short press the "M" button to conﬁrm

the selection.

②

③

①

Using the NW620 as an example:

1. Turn oﬀ the camera power. Attach t

Qpro ﬂash trigger to the camera's h

shoe socket. Turn on the power

switch for the trigger and the came

Press and hold the Qpro <Zm/CH>

button to set the channel, and

press the <MENU> button to

select the <ID> setting.

2. Attach the NW620 to the QR receiv

Press <M> to enter the channel and

ID mode. Use the <+>/<-> buttons t

set the same channel and ID value

as the Qpro ﬂash trigger.

3. Turn on the power of the NW620 on-camera

ﬂash and set it to on-camera ﬂash mode.

Press the camera shutter to trigger the ﬂash.

To use:

1. art by turning oﬀ the camera power. St

Connect the 2.5mm shutter cable to the

camera's shutter jack and the other end

to the sync jack of the QR receiver. Turn

on both the QR power switch and the

camera power. Long-press the <M>

button on the QR receiver to a ess cc

the sync port selection interface.

Short press the <+>/<-> buttons to

select the remote shutter option < >, then

short press the <M> button to conﬁrm.

2. Next, short press the <+>/<-> buttons

on the QR receiver's <M> button to set the

desired channel and ID mode. Use the <+>/<->

buttons to adjust the QR receiver's channel

and ID values a ordingly.cc

3. Turn on the Qpro transmitter switch and

ensure it is set to the same channel and

ID value as the QR receiver.

To activate the camera's focus, half-press the

Qpro transmitter's < > button. To trigger the

camera shutter, long-press the Qpro

transmitter's < > button.

3. Using a 2.5mm shutter cable to

trigger the camera shutter

Using the S101-400W as an example:

1. Begin by turning oﬀ the camera power.

Attach the Qpro ﬂash trigger to the

camera's hot shoe socket. Turn on

the power switch for both the trigger

and the camera. Press and hold the

Qpro <Zm/CH> button to set the

desired channel, and press the

<MENU> button to a ess the cc

<ID> setting.

2. After powering on the ﬂash, connect

the 2.5mm sync interface cable to the

sync jack of the ﬂash, and the other

end to the sync jack of the QR receiver.

Turn on both the QR power switch and

the ﬂash switch. Press and hold the <M>

button to enter the sync port selection

interface. Use short presses of the

<+>/<-> button to select the ﬂash icon

< >, then brieﬂy press <M> to conﬁrm

the selection. Next, short press the QR

<M> button to set the desired channel

and ID mode. Adjust the channel and ID

value using short presses of the <+>/<->

button to match those set on the Qpro

ﬂash trigger.

3. Finally, press the camera shutter to trigger

the ﬂash.

4. Using a 2.5mm sync cable to

trigger the studio monolights

Installation Instructions

Installation Instructions Installation Instructions Using the product

Flash can be triggered through the 2.5mm sync interface

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

CAUTION: The user is cautioned that changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment oﬀ

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit diﬀerent from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

2. This equipment complies with RF radiation exposure limits set forth for

an uncontrolled environment.

The device has been evaluated to meet general RF exposure requirement. The device

can be used in portable exposure condition without restriction.

Produkt Specifikationer

Mærke:	Neewer
Kategori:	Ikke kategoriseret
Model:	QR

Har du brug for hjælp?

Hvis du har brug for hjælp til Neewer QR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Neewer Manualer

Neewer QR Manual

8 Oktober 2024

Neewer X14 III Manual

7 Oktober 2024

Neewer X12 II Manual

24 September 2024

Neewer ST83 Manual

5 September 2024

Neewer SP-02 Manual

5 September 2024

Neewer NK-ST0203 Manual

4 September 2024

3 September 2024

3 September 2024

3 September 2024

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MPM -48-CW-48 Manual

9 November 2024

Alpine KAE-123C Manual

8 November 2024

IFM AC434S Manual

8 November 2024

Alpine SBS-0515 Manual

8 November 2024

Alpine KCE-103V Manual

8 November 2024

Alpine KCE-104V Manual

8 November 2024

Advantech ECU-1051TL Manual

8 November 2024

Alpine DDC-R13A Manual

8 November 2024

Alpine HCE-C200F Manual

8 November 2024

Alpine CRM-1652RF Manual

8 November 2024