NightStick LGL-180-IR Manual

NightStick Ikke kategoriseret LGL-180-IR

Læs nedenfor 📖 manual på dansk for NightStick LGL-180-IR (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/3
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
INS-LGL-170-20b
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
INS-LGL-170-20b
Instruction Manual
LGL-170
LGL-170 with Tail Cap Switch mounted on AR.
WEAPON SAFETY
FAILURE TO FOLLOW SAFETY AND OPERATING
MEASURES WHEN HANDLING A FIREARM OR THE
NIGHTSTICK LGL WHEN MOUNTED ON A FIREARM IS
DANGEROUS AND CAN RESULT IN SERIOUS INJURY,
DAMAGE TO PROPERTY, OR DEATH.
Use of a fi rearm under any circumstance is inherently
dangerous. SERIOUS INJURY OR EVEN DEATH may
result without proper training in the safe handling of
fi rearms. Proper training should be obtained from an
accredited fi rearms safety program conducted by a
qualifi ed instructor.
Read, understand and follow all of the safety
instructions that come with your fi rearm before attaching
your new LGL.
Always assume every fi rearm is loaded and treat that
fi rearm as such.
Never point a fi rearm at anything that you are not willing
to destroy.
Never service your fi rearm or your LGL when mounted
on a fi rearm without fi rst activating the weapon’s safety (if
applicable), removing the magazine, opening the action
and physically and visually inspecting to make sure that
no ammunition is installed in the fi rearm.
WEAPON MOUNTED LIGHT SAFETY
Nightstick recommends that the LGL should only be
activated with the non-trigger hand (support hand) while
employing a two-hand grip on the weapon and with
the trigger fi nger fully outside the trigger guard when
applicable.
Thoroughly practice (employing safe training
conditions) with the LGL and an unloaded weapon.
PICATINNY AND OFFSET MOUNTS
Reverse the Picatinny Mount (LGL-SM1)
The factory-installed, standard Picatinny mount is
reversible to provide additional clearance on the rifl e or to
better position the thumbscrew.
Remove the two machine screws and split washers using
the included 2.5mm Allen wrench.
Reverse the mount and reinstall the hardware.
Change to the Offset Mount (LGL-OM1)
The offset mount can be attached to any section of a
Picatinny rail and can also be reversed.
Remove the Picatinny mount as described in section
above.
Install the offset mount onto the light and reinstall the
hardware.
NOTE: The included machine screws come with blue
threadlocker from the factory. Repeated removal and
reinstallation of the screws may necessitate adding more
threadlocker. CAUTION: Do not use red threadlocker as it
will make it too diffi cult to remove the screws in the future.
MOUNT THE LIGHT ONTO THE RIFLE
ALWAYS ENSURE HANDGUN IS SAFE AND UNLOADED
BEFORE MOUNTING THE LIGHT.
Loosen the thumbscrew on the mount.
Place the mount and light in the desired location on any
section of Picatinny rail.
Tighten the thumbscrew by hand.
Periodically check the thumbscrew for tightness.
ATTACH THE PRESSURE PAD SWITCH
Option 1: Rail Connector (NS-PIC1)
The rail connector mount can be used to attach the
pressure switch pad to any section of a Picatinny rail.
Position the mount onto the rail with the open end in the
direction you prefer.
Align the protrusions with the rail slots and snap mount
into place.
Slide the pressure switch pad into the open end of the
mount until fully seated.
Option 2: Velcro®
The included Velcro® pads come with two strips of
pressure sensitive adhesive (PSA) already attached that allow
the pressure switch pad to be adhered to any clean smooth
surface of your fi rearm. The Velcro® allows the pressure
switch pad to be temporarily removed from the fi rearm.
Use the included alcohol prep pad to clean the surface of
the fi rearm where the RPS is to be attached and the back
of the RPS. Allow to dry.
Remove the backing strip from one side of the PSA tape
and attach it to the back of the RPS.
Repeat that process to attach the RPS/Velcro® pad
assembly to the fi rearm.
Apply even pressure. Allow the PSA tape to cure for
approximately 24 hours for the best adhesion.
Option 3: Vertical Fore Grip
Various aftermarket manufacturers make vertical fore
grips that the Nightstick pressure switch pad will fi t into.
The TangoDown® (models BGV-MK46 or BGV-QDSF)
vertical fore grips allow the pressure switch pad to slide
perfectly into the molded slot of their grip.
Other vertical fore grips that have the same profi le will
work with the RPS.
SECURE THE RPS CABLE TO THE RIFLE
The Wire Management Clamp (NS-WM1) is used to secure
the wire from the RPS to the rifl e to prevent a snag hazzard.
Loosen the cross screw and pull the clamp apart.
Position the RPS cable through the paths of the molded
channels of the clamp. The cable can pass straight through
one path, or turn 90 degrees under the clamp and come
out on the side.
Install clamp body onto rail at desired location to hold the
cable in place.
Reassemble clamp using guide pin bosses for alignment.
Reinstall the Allen cross screw and tighten with the
included Allen wrench. Do not overtighten.
OPERATION
Pressing either switch will activate the light. Both provide
momentary or constant-on operation.
Tail Cap Switch
Constant on/off: Press until switch clicks to turn on or off.
Momentary on: Lightly press and hold for .5 seconds or
longer. Release to turn off.
Remote Pressure Switch
Turn on/off: Press the small, square shielded switch until
it clicks to turn on or off.
Momentary on: Lightly press the long tape switch and
hold for .5 seconds or longer. Release to turn off.
STROBE WARNING
Exposure to strobing lights may cause dizziness,
disorientation, and nausea. A very small percentage of people
suffer from photosensitive epilepsy and may experience
seizures or blackouts triggered by strobing lights. For more
information from the EPILEPSY FOUNDATION about
photosensitivity and seizures, please visit www.epilepsy.
com. Anyone who has had symptoms linked to this condition
should consult a doctor before using this product.
WARRANTY
LIMITED LIFETIME WARRANTY
Bayco Products, Inc. warrants this product to be free
from defects in workmanship and materials for the original
purchaser’s lifetime. The Limited Lifetime Warranty includes the
LEDs, housing and lenses. Rechargeable batteries, chargers,
switches, electronics and included accessories are warranted
for a period of two years with proof of purchase. Normal wear
and failures which are caused by accidents, misuse, abuse,
faulty installation and lightning damage are excluded.
We will repair or replace this product should we determine
it to be defective. This is the only warranty, expressed or
implied, including any warranty of merchantability or fi tness
for a particular purpose.
For a complete copy of the warranty, go to www.
baycoproducts.com/nightstick-product-support/warranties.
Retain your receipt for proof of purchase.
BEFORE ATTACHING, INSPECTING
OR SERVICING THE LGL
WARNING: IT IS IMPERATIVE THAT SAFETY
MEASURES BE EMPLOYED AT ALL TIMES WHILE
HANDLING A FIREARM.
Engage the safety on the fi rearm (if applicable).
Remove the magazine from the fi rearm (if applicable).
Open the action and visually and physically inspect the
chamber to be sure it is empty.
Keep the barrel pointed in a safe direction at all times and
never place your hand in front of the muzzle.
GENERAL SAFETY WARNINGS
NOT FOR USE ABOVE HAZARDOUS LOCATIONS
DO NOT use in explosive atmospheres, near fl ammable
liquids, or where explosion proof lamps are required.
DO NOT use in the proximity of vehicles or equipment
when there is a risk of fl ammable liquids coming into
contact with the fl ashlight.
DO NOT expose the batteries to water or salt water, or
allow the batteries to get wet.
DO NOT store the batteries with metallic objects that
may cause a short circuit.
Immediately discontinue use of the batteries if they emit
an unusual smell, feel hot, change color, change shape or
appear abnormal in any way.
Keep out of the reach of children.
INSTALL THE BATTERY
ALWAYS ENSURE HANDGUN IS SAFE AND UNLOADED
BEFORE CHANGING THE BATTERY.
Fully charge one of the batteries before use and have the
other battery charged and ready as needed.
Unscrew the tail cap switch or the tail cap on the remote
pressure switch.
Insert the lithium-ion battery into the light with the
positive(+) end fi rst.
Replace the tail cap and fully tighten by hand.
OPTIONAL: The LGL-170 can also be powered using 2
CR123 batteries. Note: Lumen output may slightly be reduced.
INSTALL REMOTE PRESSURE SWITCH
The product ships with the tail cap switch pre-installed
by the factory. It can be replaced with the included Remote
Pressure Switch (LGL-RPS2).
To change to the remote pressure switch, unscrew the tail
cap switch. Install the remote pressure switch and tighten.
Keep tail cap switch for future use so the light can be
converted back to a hand-held fl ashlight in the future.
NOTE: The strain relief of the RPS can be rotated 360
degrees to aid in cable management.
LGL-170 with Remote Pressure Switch mounted on AR using
Wire Management Clamp.

Produkt Specifikationer

Mærke: NightStick
Kategori: Ikke kategoriseret
Model: LGL-180-IR

Har du brug for hjælp?

Hvis du har brug for hjælp til NightStick LGL-180-IR stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret NightStick Manualer

NightStick

NightStick TCM-5B Manual

3 September 2024
NightStick

NightStick LGL-180-IR Manual

1 September 2024
NightStick

NightStick LGL-170A Manual

1 September 2024
NightStick

NightStick TCM-10F Manual

1 September 2024
NightStick

NightStick TWM-30 Manual

31 August 2024
NightStick

NightStick LGL-150 Manual

31 August 2024
NightStick

NightStick TCM-550XL Manual

31 August 2024
NightStick

NightStick LGC-550XL Manual

31 August 2024
NightStick

NightStick TSM-14G Manual

31 August 2024
NightStick

NightStick TSM-13W Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SKROSS

SKROSS World Adapter Pro+ Manual

26 November 2024
SKROSS

SKROSS PRO – World & USB Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024