Oregon Scientific PE326PM Manual


Læs nedenfor 📖 manual på dansk for Oregon Scientific PE326PM (3 sider) i kategorien Skridttæller. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
increase the value rapidly.
5. Press MODE to confirm the change and move on to the
next setting.
6. Repeat 3, 4 to complete setting minute and second
values.
ADJUSTING THE SETTINGS
DISTANCE AND CALORIES
Total distance = steps taken x average step length.
Measuring distance correctly depends on setting the correct
average length of individual stride.
Precise calories burned calculations require taking into
account many factors. The PE326PM uses body weight and
the number of steps taken to give a good estimate.
To set stride length and body weight:
1. In DIST / TIMER CAL / TIMER or mode press and hold
MODE for two seconds to enter STRIDE / WEIGHT
display. The stride numbers will flash.
2. Press RESET / until the desired length of stride is
selected (30 to 150 cm or 11 to 60 inches)*.
3. Press MODE, the weight numbers will flash.
4. Press RESET / until desired weight setting is reached
(30-150 kg or 65-340 lbs)*.
5. Press MODE to confirm and exit.
TIP Individual stride-length varies. Input an appropriate
length for an average stride. To determine length of stride
walk 10 paces and divide distance traveled by 10.
NOTE To make the unit more or less sensitive to motion,
reposition the motion sensitivity switch. To determine the
proper amount of motion sensitivity, experiment with different
settings.
MOTION SENSITIVITY
Follow these important procedures to adjust the Motion
Sensitivity and ensure accurate readings:
1. Correctly position and attach the unit to a belt or
waistband.
2. Reset step counter to zero.
3. Walk at a normal pace; take at least 100 steps.
4. Adjust sensitivity switch if walking speed changes.
Repeat steps 2-4 until accurate reading is obtained.
The following conditions may cause incorrect reading
of steps taken:
1. Uneven walking pace, such as walking in crowded areas
or on uneven floor.
2. Frequent up and down movements, such as standing
up and/or sitting down; running, jumping, going up and
down stairs etc.
USING THE PEDOMETER
COUNT-UP TIMER
The count-up timer will start from zero and count to a
maximum time of 99 hours, 59 minutes, and 59 seconds
(99:59’59”).
1. In DIST / TIMER CAL / TIMER or mode press ST / SP to
start the timer.
2. Press again to stop the timer.ST / SP
To reset the timer to zero, press RESET / in DIST / TIMER
or CAL / TIMER mode.
TO VIEW VALUES
To view steps taken, distance traveled and calories
burned:
Press MODE to enter the desired mode.
To reset the values, press RESET / in STEP mode.
NOTE The total distance and calories burned will be
cleared along with the total steps.
MEASURING PULSE RATE
The built-in Pulse meter provides an easy way to measure
your pulse rate while working out.
A person’s pulse rate indicates the number of times that the
heart beats within a given amount of time. This unit attempts
to calculate approximately how many times a heart will beat
in one minute.
Place your finger loosely on the Pulse meter on the outside
of the unit.
1. Press to enter PULSE mode. The symbol will flash
while pulse is measured.
2. The pedometer will return to previous mode a few
seconds after finger is removed. Alternatively, press
to exit PULSE mode.
PULSE RATE TROUBLESHOOTING
If you cannot get a reading or think yours is not correct,
follow these tips to ensure accurate measurements:
Cold fingertips and chill air can affect the measurement.
You may need to warm your hands before you start.
The sensor is sensitive to light sources. Cover the entire
sensor area with your fingertip to block all light.
Gently touch the pulse sensor; do not press hard.
Keep still and calm during measurement. Moving about
can affect the reading.
Wait the proper amount of time: measurements can take
6-12 seconds depending on the stability of the signals
received.
FITNESS TIPS
To keep fit, it generally takes a person weighing 60kg to
walk 10,000 steps to burn approximately 300 calories. The
following diagram will give you some basic reference to the
calorie consumption for people of various weights.
PRECAUTIONS
• Do not subject the unit to excessive force, shock, dust,
temperature or humidity.
• Do not cover the ventilation holes with any items such as
newspapers, curtains etc.
• Do not immerse the unit in water. If you spill liquid over it,
dry it immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive materials.
• Do not tamper with the unit ’s internal components. This
invalidates the warranty.
• Only use fresh batteries. Do not mix new and old batteries.
• Images shown in this manual may differ from the actual
display.
• When disposing of this product, ensure it is collected
separately for special treatment.
• Placement of this product on certain types of wood may
result in damage to its finish for which Oregon Scientific
will n ot b e r e s p o n s i bl e . C o ns ul t t h e f ur ni t u r e
manufacturer’s care instructions for information.
• The contents of this manual may not be reproduced
without the permission of the manufacturer.
• Do not dispose old batteries as unsorted municipal waste.
• Collection of such waste separately for special treatment
is necessary.
• Please note that some units are equipped with a battery
safety strip. Remove the strip from the battery compartment
before first use.
NOTE The technical specifications for this product and the
contents of the user manual are subject to change without
notice.
SPECIFICATIONS
TYPE DESCRIPTION
Operating modes STEP, DIST / TIMER, CAL / TIMER
Real time clock 12 hour / 24 hour option with
hour / minute / second display
Step counter 0 to 99,999 steps
Distance traveled 0 to 999.99 km
(0 to 999.99 miles)*
Count-up timer 99 hours, 59 minutes, 59 seconds
Stride distance 30 to 150 cm (11 to 60 inches)*
Calorie 0.1 to 9999.9 kcal
Weight range 30 to 150 kg (60 to 340 lbs)*
Pulse range 40 to 206 bpm
Operating temp -10 to 40 °C (14 to 104 °F)
Storage temp -20 to 60 °C (-4 to 140 °F)
Batteries 2 x LR44 1.5V
Battery life 1 year
Product size 64 x 33 x 40 mm
(L x W x H) (2.52 x 1.30 x 1.58 inches)
Weight 33.0 g (1.16 ounces)
NOTE *Imperial units of measure are used on US models
only and metric units of measure are used on EU / UK
models only.
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn more
about Oregon Scientific products.
If you’re in the US and would like to contact our Customer
Care department directly, please visit:
www2.oregonscientific.com/service/support.asp
OR
Call 1-800-853-8883.
For international inquiries, please visit:
www2.oregonscientific.com/about/international.asp.
Pedometer with Pulse Meter
Model: PE326PM
USER MANUAL
EN
INTRODUCTION
Thank you for selecting an Oregon Scientific pedometer
(PE326PM).
Please keep this manual for instructions and information you
should know about.
KEY FEATURES
FRONT VIEW
1. Pulse meter: Insert finger to measure pulse rate
2. COVER RELEASE: Press to open protective cover
3. Battery compartment
INTERIOR
1. MODE: Toggles between STEP, DIST / TIMER and
CAL / TIMER
2. Starts / Stops timerST / SP:
3. : Turns backlight on
4. Motion Sensitivity switch: Increases or decreases unit
sensitivity
5. : PULSE Press to enter mode
6. RESET / : Resets display mode values to zero,
increases value in settings
7. Belt clip
LCD
1. Displays when in modePULSE
2. Displays when batteries are low
3. Displays when calories are shown
4. Displays when timer is running
5. AM / PM for 12 hour format
6. Indicating mode displayed:
STEP displays the number of steps taken and the
clock
displays the distance traveled and the DIST / TIMER
count-up timer
CAL / TIMER displays the approximate number of
calories burned and the count-up timer
7. Distance in km or mile*
8. Weight in kg or lbs*
9. Displays when in Timer Mode
10. Stride in cm or inches*
NOTE *Imperial units of measure are used on US models
only and metric units of measure are used on EU / UK
models only.
GETTING STARTED
INSULATION TAPE
Before using the device, pull out the insulation tape
underneath the battery cover.
NOTE The unit will not work until the tape is pulled out.
BATTERIES
To change the batteries:
1. Gently press and pull the battery compartment door.
2. Insert 2 x LR44 size 1.5V batteries or equivalent.
3. Replace the battery compartment door.
NOTE Protect the environment by taking exhausted
batteries to authorized disposal stations.
Shows when batteries are low.
To open the cover:
Holding the pedometer upright, grasp the clip with one hand
and press the COVER RELEASE button with the other.
CLOCK
1. Press MODE STEP until the mode is displayed.
2. Press and hold for two seconds. The 12-hour MODE
value will flash. Press RESET / to select between 12
hour and 24 hour format.
3. Press MODE, the “hour” digits will flash.
4. Press RESET / to alter hour value. Press and hold to
If unit shows more
steps than actual
number of steps taken,
slide switch toward ”.-
If unit shows fewer
steps than actual
number of steps taken,
slide switch toward ” .+
1
2
3
1 5
6
7
2
3
4


Produkt Specifikationer

Mærke: Oregon Scientific
Kategori: Skridttæller
Model: PE326PM

Har du brug for hjælp?

Hvis du har brug for hjælp til Oregon Scientific PE326PM stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skridttæller Oregon Scientific Manualer

Skridttæller Manualer

Nyeste Skridttæller Manualer

TFA

TFA 42.2003 Manual

5 September 2024
Silva

Silva ex connect Manual

27 August 2024
BandeeFit

BandeeFit BFX-4 Manual

25 August 2024
Dexford

Dexford PE 500 Manual

24 August 2024
Dexford

Dexford PE 200 Manual

24 August 2024
Dexford

Dexford PE 400 Manual

24 August 2024
BandeeFit

BandeeFit BFQ-8 Manual

22 August 2024