Ozito JSW-8100U Manual

Ozito savemaskine JSW-8100U

Læs nedenfor 📖 manual på dansk for Ozito JSW-8100U (4 sider) i kategorien savemaskine. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

iSC GmbH · Eschenstraße 6 · 94405 Landau /Isar · Germany

All of our products undergo strict quality checks to ensure that they reach

you in perfect condition. In the unlikely event that your device develops a

fault, please contact our service department at the address shown on this

guarantee card. You can also contact us by telephone using the customer

service number shown. Please note the following terms under which

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the

manufacturer mentioned below promises to buyers of its new products

in addition to their statutory guarantee claims are not a󰀨ected by this

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or

manufacturing faults on a product which you have bought from the

manufacturer mentioned below are limited to either the rectication of said

defects on the product or the replacement of the product, whichever we

prefer.

Please note that our devices are not designed for use in commercial, trade

or professional applications. A guarantee contract will not be created if the

device has been used by commercial, trade or industrial business or has

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly

instructions or due to incorrect installation, a failure to follow the operating

instructions (for example connecting it to an incorrect mains voltage or

current type) or a failure to follow the maintenance and safety instructions

or by exposing the device to abnormal environmental conditions or by lack

of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example

overloading the device or the use or unapproved tools or accessories),

ingress of foreign bodies into the device (such as sand, stones or dust,

transport damage), the use of force or damage caused by external forces

(for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original

date of purchase and is intended for DIY (Do It Yourself) use only. Warranty

excludes consumable parts. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the

guarantee period. The original guarantee period remains applicable to the

device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work

performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR

Please refer to the restrictions of this warranty concerning wearing parts,

consumables and missing parts as set out in the service information in

these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

0118

PENDULUM

JIGSAW

810W

ORIGINAL INSTRUCTIONS

SPECIFICATIONS

JSW-8100U

WHAT’S IN THE BOX

Jigsaw

Dust Extraction Adaptor

Hex Key

Parallel Guide

3 x Cutting Blades

MAINTENANCE

TROUBLESHOOTING

1. After each use, blow air through the tool housing to ensure it is free from all

dust particles that may build up. Build up of dust particles may cause the tool to

overheat and fail.

2. If the enclosure of the tool requires cleaning do not use solvents but a moist

soft cloth only. Never let any liquid get inside the tool; never immerse any part

of the tool into a liquid.

Carbon Brushes

When the carbon brushes wear out, the jigsaw

will spark and/or stop. Discontinue use as soon

as this happens. They should be replaced prior to

recommencing use of the jigsaw. Carbon brushes

are a wearing component of the jigsaw therefore

not covered under warranty. Continuing to use the

jigsaw when carbon brushes need to be replaced

may cause permanent damage to the jigsaw. Carbon

brushes will wear out after many uses but when the carbon brushes need to be

replaced, take the jigsaw to an electrician or a power tool repairer for a quick

and low cost replacement. Always replace both carbon brushes at the same

time.

Note: Ozito Industries will not be responsible for any damage or injuries

caused by the repair of the jigsaw by an unauthorised person or by mishandling

of the jigsaw.

Excessive sparking visible through the housing air vents

and/or the jigsaw failing to operate

May indicate the carbon brushes have worn out and need to be

replaced. Carbon brushes should only be replaced by a qualied

electrician or power tool repairer.

Cutting Metal

Your jigsaw can be used for cutting light gauge ferrous sheet and non-ferrous

metals such as copper, brass, aluminium, etc. It is advisable when cutting sheet

metal to clamp a backing sheet of soft wood or plywood to the work as this will

enable you to obtain a clean cut without vibration and the possibility of tearing the

metal. Both metal and wood backing are sawn together. Do not force the cutting

blade into the metal as this will reduce the life of the blade and possibly damage

the motor. Cutting thin metal will take longer than cutting even a relatively thick

piece of wood, so do not be tempted to speed up the operation by forcing the

saw. Spread a thin lm of oil along the proposed cutting line before commencing

to saw metal. Always select the right blade for the job.

WARRANTY

SPARE PARTS

ozito-diy.co.uk

WARNING!

• Always check the saw, the power cable and the plug before use. Only ever use the saw if it is in

perfect, undamaged condition. Damaged parts have to be repaired or replaced immediately by a

qualied electrician.

• Always pull the plug out of the power socket before carrying out any work on the saw, before

changing the blade and in periods of non-use.

• Always run the power cable away from the back of the saw to guard it from damage.

• For outdoors work use only suitably approved extension cables with a minimum conductor cross

section of 1,5 mm2. The plug connectors must have earthing contacts and be splash-proof.

• Keep the saw in a safe place and out of the reach of children.

• Always wear goggles, safety gloves and ear mu󰀨s when sawing. Wear a breathing mask on

dusty jobs.

• Never leave any keys or adjustment spanners in position on the saw. Before switching on, check

that all keys and adjustment spanners have been removed.

• Secure the workpiece (with a clamp) so that it cannot slip.

• It is prohibited to use the saw on asbestos materials. Please note the accident prevention

regulations in force in your country.

• Use only original spare parts.

• Repairs are to be carried out by qualied electricians only.

• The level of noise at the workplace may exceed 85 dB(A). In this case you will need to introduce

noise protection measures for the user.

• Make sure of your footing. Avoid abnormal working positions.

• Keep your electric tool out of the rain. Never use electric tools in wet or damp conditions, and

never use them near inammable liquids.

• Never carry the electric tool by its power cable. Keep the power cable safe from damage. Oil,

solvent and sharp edges can damage cables.

• Keep your workplace tidy.

• Make sure the power switch is o󰀨 before inserting the plug in the socket.

• Wear suitable clothing. Never wear loose-tting clothes or jewelry. Use a hair-net on long hair.

• For your own safety, use only the manufacturer’s accessories and attachments.

• Use only sharp saw blades that are in perfect condition. Replace bent and cracked saw

blades immediately.

• After switching o󰀨 the saw, do not press against the side of the blade to bring it to a halt.

• Always cut at a steady rate of progress. This will prevent accidents and prolong the life of your

saw and the blade.

• Use only a damp cloth to clean your saw. Do not use any aggressive agents for cleaning

purposes.

• Check your saw to ensure that it is in good working order. If the saw fails to work properly, have

it checked. Leave all maintenance and inspection work strictly to a qualied electrician or ISC

GmbH.

• Check the fastening screws

Check the fastening screws regularly and make sure that they are all securely tightened. Tighten

any loose screws immediately, otherwise there is the risk of serious injuries.

• Hold the equipment by the insulated handles when carrying out work during which the

plug-in tool could strike concealed power cables or its own mains lead. Contact with a live

cable can also make the metal parts of the equipment live and will cause an electric shock.

• Use clamps or some other means to fasten and secure the workpiece to a sturdy surface.

If you hold the workpiece only with your hand or against your body it will remain unstable and

might cause you to lose control.

Do not lose these safety instructions

JIGSAW SAFETY WARNINGS

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

9. POCKET CUTTING

A pocket cut is when you need to cut a hole in the middle of a

workpiece

OPERATION

2 Pass the blade through the hole and begin the cut.

1 Drill a hole in the

workpiece using a

drill bit.

TIM BER BLADE

METAL BLADE

DECLARATION OF CONFORMITY

Nigel Yang/Product-ManagementAndreas Weichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Pendulum Jigsaw-8100U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

(EU)2015/1188

2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EU

2014/68/EU

(EU)2016/426

Notiﬁ ed Body:

(EU)2016/425

X 2011/65/EU_(EU)2015/863

X 2006/42/EC

Annex IV

Notiﬁ ed Body:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured LWA = dB (A); guaranteed LWA = dB (A)

P = KW; L/Ø = cm

Notiﬁ ed Body:

2012/46/EU_(EU)2016/1628

Emission No.:

Standard references: EN 62841-1; EN 62841-2-11; EN 55014-1; EN 55014-2;

EN 61000-3-2; EN 61000-3-3; EN 62321

Landau/Isar, den 11.12.2019

First CE: 17 Archive-File/Record: NAPR017964

Art.-No.: 30.002.44 I.-No.: 11017 Documents registrar: Georg Riedel

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Spare parts can be ordered from the Special Orders

Desk at your local Bunnings Warehouse or Homebase

store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

SOUND & VIBRATION

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric

and electronic equipment and its implementation in national laws, old

electric power tools have to be separated from other waste and disposed

of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the

owner of the electrical equipment must make sure that the equipment is

properly disposed of if p1-he no longer wants to keep the equipment. The old

equipment can be returned to a suitable collection point that will dispose

of the equipment in accordance with the national recycling and waste

disposal regulations. This does not apply to any accessories or aids

without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of

documentation and papers accompanying products is permitted only with

the express consent of the iSC GmbH.

Subject to technical changes

Sound and vibration values were measured in accordance with EN 60745.

Lpa sound pressure level: 85.0 dB

pa uncertainty: 3 dB

Lwa sound power level: 96.0 dB

wa uncertainty: 3 dB

Wear ear-mu󰀨s.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions) determined in

accordance with EN 60745.

Cutting wood

Vibration emission value ah = 12.06 m/s2

K uncertainty = 1.5 m/s2

Cutting sheet metal

Vibration emission value ah = 9.80 m/s2

K uncertainty = 1.5 m/s2

Additional information for electric power tools

Warning!

The specied vibration value was established in accordance with a

standardized testing method. It may change according to how the electric

equipment is used and may exceed the specied value in exceptional

circumstances.

The specied vibration value can be used to compare the equipment with other

electric power tools.

The specied vibration value can be used for initial assessment of a harmful

e󰀨ect.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance o󰀨 when it is not in use.

• Wear protective gloves.

DESCRIPTION OF SYMBOLS

Danger! Read the operating instructions to reduce the risk of

inquiry.

Caution! Wear ear-mu󰀨s. The impact of noise can cause

damage to hearing.

Caution! Wear a breathing mask. Dust which is injurious to

health can be generated when working on wood and other

materials. Never use the device to work on any materials

containing asbestos!

Caution! Wear safety goggles. Sparks generated during

working or splinters, chips and dust emitted by the device can

cause loss of sight.

Double insulated / Protection class II

SERVICE INFORMATION

Please note that the following parts of this product are subject to normal

or natural wear and that the following parts are therefore also required

for use as consumables.

* Not necessarily included in the scope of delivery!

Category Example

Wear parts* Guide roller, Carbon brushes

Consumables* Saw blades

Missing parts

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of re, electric shock, personal injury and

material damage.

Read the whole manual carefully and make sure you know how to switch the tool o󰀨 in an emergency,

before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the equipment to the mains supply make sure that the data on the rating plate are

identical to the mains data.

This tool is double insulated therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid

a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The

insulation system is for added protection against injury resulting from a possible electrical insulation failure

within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the

extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not

suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric

shock.

WARNING! Read all the safety information, instructions, illustrations and technical data

provided on or with this power tool. Failure to adhere to the following instructions may result in

electric shock, re and/or serious injury.

Keep all the safety information and instructions in a safe place for future use.

The term „power tool“ used in the safety information and instructions refers to power tools operated

from the mains power supply (with a power cable) and to battery operated power tools (without a

power cable).

1. Workplace safety

a) Keep your work area clean and well lit. Untidy or unlit work areas can result in accidents.

b) Do not use this power tool in an area where there is a risk of explosion and where there are

inammable liquids, gases or dust. Power tools generate sparks that can ignite dust or vapors.

c) Keep children and other people away from the power tool while you are using it. If you are

distracted you may lose control of the power tool.

2. Electrical safety

a) The plug on the power tool must t into the socket. The socket must not be modied in any way. Do

not use adapter plugs together with power tools with a protective earth. Unmodied plugs and matching

sockets will reduce the risk of an electric shock.

b) Avoid body contact with earthed surfaces such as pipes, heating systems, stoves and

refrigerators. There is an increased risk of su󰀨ering an electric shock if your body is earthed.

c) Keep the power tool out of the rain and away from moisture. The ingress of water into an electric

power tool increases the risk of an electric shock.

d) Do not use the power cable for a purpose for which it is not designed, for example to carry the

power tool, hang it up or to pull the plug out of the socket. Keep the power cable away from heat,

oil, sharp edges and moving parts. Power cables that are damaged or tangled increase the risk of an

electric shock.

e) If you use an electric power tool outdoors, use only extension cables that are suitable for outdoor

use. The use of an extension cable which is suitable for outdoor use reduces the risk of an electric

shock.

f) If you cannot avoid using the power tool in a damp location, use a residual current device

(RCD) circuit breaker. The use of a residual current device (RCD) circuit breaker will reduce the risk of

su󰀨ering an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and be sensible and responsible when using an electric

power tool. Never use the power tool if you are tired or under the inuence of drugs, alcohol or

medication. One moment of inattention when using the electric tool can result in serious injuries.

b) Wear personal safety equipment and always wear safety goggles. Wearing personal safety

equipment such as dust masks, non-slip safety shoes, a helmet or ear plugs, depending on the type and

application of the tool, reduces the risk of injury.

c) Make sure that the tool cannot start up accidentally. Ensure that the power tool is switched o󰀨 before

you connect it to the power supply and/or connect the battery pack, pick it up or carry it. If you have your

nger on the switch while carrying the power tool or if you connect the power tool to the power supply

while it is switched on, this may cause accidents.

d) Remove all adjusting tools or wrenches before you switch on the power tool. Any tool or wrench in

a rotating part of the power tool could cause injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep your balance at all times.

This will enable you to control the power tool better in unexpected situations.

f) Wear suitable clothes. Never wear loose tting clothes or jewelry. Keep hair and clothing away from

moving parts. Loose clothing, jewelry or long hair can be caught by moving parts.

g) If dust extraction devices and dust collection devices can be tted, they must be connected and

must be used correctly. The use of a dust extractor can reduce the dangers posed by dust.

h) Do not allow yourself to be lulled into a false sense of security and do not ignore the safety

regulations covering electric power tools, even if you are familiar with the power tool after having

used it many times. Carelessness can lead to serious injuries in just a fraction of a second.

4. Using and handling the power tool

a) Do not overload your power tool. Use the correct electric tool for the job in hand. The correct tool will

enable you to work better and more safely within the specic performance range.

b) Do not use an electric power tool if the switch is defective. An electric power tool that cannot be

switched on or o󰀨 is dangerous and must be repaired.

c) Pull the plug out of the socket and/or remove the removable battery pack before making any

adjustments to the tool, changing plug-in tool parts or putting the power tool down. These

precautions will prevent the power tool starting accidentally.

d) Keep unused electric tools out of the reach of children. Do not allow people who are not familiar

with the power tool or who have not read these instructions to use the power tool. Electric tools are

dangerous if they are used by inexperienced people.

e) Look after power tools and plug-in tools with care. Check that moving parts function correctly and do

not jam, and whether any parts are broken or damaged such that they adversely a󰀨ect the function of the

power tool. Have damaged parts repaired before you use the power tool. Many accidents are caused by

poorly maintained electric tools.

f) Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges will

jam less and are easier to control.

g) Use the power tool, plug-in tools, etc. as set out in these instructions. Take account of the

conditions in your work area and the job in hand. Using electric tools for purposes other than the one for

which they are designed can result in dangerous situations.

h) Keep the handles and grip surfaces dry, clean and free from oil and grease. If the handles and grip

surfaces are slippery, it will not be possible to operate and control the power tool safely in unforeseen

situations.

5. Service

a) Have your power tool repaired only by trained personnel using only genuine spare parts. This will

ensure that your power tool remains safe to use.

Anleitung_JSW_8100U.indd 1-4

Anleitung_JSW_8100U.indd 1-4Anleitung_JSW_8100U.indd 1-4 12.12.2019 12:37:46

12.12.2019 12:37:46

12.12.2019 12:37:4612.12.2019 12:37:46

Produkt Specifikationer

Mærke:	Ozito
Kategori:	savemaskine
Model:	JSW-8100U

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito JSW-8100U stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

savemaskine Ozito Manualer

Ozito ECS-406A Manual

6 Oktober 2024

Ozito PXCCSK-4182 Manual

6 September 2024

Ozito PXBPCK-1825 Manual

6 September 2024

Ozito PXTCSK-2520 Manual

6 September 2024

Ozito PXPRSS-018 Manual

5 September 2024

Ozito PXBPCS-1815 Manual

5 September 2024

Ozito JSW-6100U Manual

21 August 2024

Ozito RTB-003 Manual

20 August 2024

Ozito RSW-5200 Manual

17 August 2024

Ozito JSW-4000U Manual

17 August 2024

savemaskine Manualer

Nyeste savemaskine Manualer

Einhell GE-CS 18 Li Manual

15 Oktober 2024

15 Oktober 2024

15 Oktober 2024

14 Oktober 2024

13 Oktober 2024

Einhell TC-AP 650 E Manual

12 Oktober 2024

Einhell TE-SM 36/210 Li Solo Manual

11 Oktober 2024

Einhell BT-SM 2534 Manual

11 Oktober 2024

Hitachi C 7MFA(LA) Manual

9 Oktober 2024

Ferrex DX254TS Manual

5 Oktober 2024