Ozito PXBPS-254U Manual

Ozito Polermaskine PXBPS-254U

Læs nedenfor 📖 manual på dansk for Ozito PXBPS-254U (3 sider) i kategorien Polermaskine. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

SPECIFICATIONS

Input: 18V

No Load Speed: 2,500/min

Pad Diameter: 254mm (10”)

Weight: 2.1kg

BUFFER

POLISHER

ORIGINAL INSTRUCTIONS

PXBPS-254U

Art.-No.: 30.002.88 I.-No.: 11017

Category Example

Wear parts* Battery

Consumables* Polishing attachments, polishing bonnets, carbon

brushes

Missing parts

STANDARD EQUIPMENT

Buffer Polisher

Polishing Bonnet

(Fleece)

Application Bonnet

(Towelling)

MAINTENANCE

DESCRIPTION OF SYMBOLS

TROUBLESHOOTING

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

• Keep ventilation slots of the polisher clean at all times to ensure efcient operation.

• After each use, blow air through the tool housing to ensure it is free from all dust, dirt, etc. Build

up of dust, dirt particles may cause the tool to overheat and shorten the life of the tool.

• If the housing of the polisher requires cleaning, do not use solvents but a moist soft cloth or soft

brush only.

• Never let any liquid get inside the tool, never immerse any part of the tool into liquid.

• No lubrication is necessary as the tool has sealed bearings.

• When not in use, the polisher should be stored in a dry, frost free location not within the reach

of children.

• The bonnets should be cleaned after each use to maximise the life and performance.

• Allow the foam pad to completely dry after each use.

WARNING! ALWAYS ENSURE THE TOOL HAS

COMPLETELY STOPPED AND THE BATTERY IS

REMOVED PRIOR TO ANY MAINTENANCE.

Battery protection system

The tool is equipped with the battery protection system, which helps to ensure a long service

life.

The output power automatically cuts off during operation when the tool and/or battery are

placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of overload, then pull the

switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the tool.

Note: The indicated capacity may be lower than the actual level during use or immediately

after using the tool.

LED lights do not illuminate on charger

Check the charging adaptor is securely plugged into the wall out let.

Check the battery is rmly connected to the charging cradle.

Check that the charging jack is securely connected to the charging cradle.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents. This is normal

and does not indicate a problem.

The polisher is not removing the compound from the

surface

Ensure a clean polishing bonnet (not the application bonnet) is tted to the polisher.

BUFFER POLISHER SAFETY WARNINGS

0318

• Ensure that the polishing bonnet is securely fastened to the polishing disk.

• Do not touch any rotating parts!

• Before you switch on, make sure that the polishing disk is not blocked and can run without any danger.

• Always check the polishing bonnets and the polishing disk for damage.

• Replace torn or damaged polishing bonnets / polishing disk immediately.

• Do not switch on the polishing machine until the polishing disk is resting on the surface you want to polish.

• Do not use any abrasives; these can destroy the lacquer.

• Harmful dust can develop during dry polishing. Be sure to wear a suitable dust mask to protect you from inhaling this

dust.

This equipment is not designed to be used by people (including children) with limited physical, sensory or mental

capacities or those with no experience and/or knowledge unless they are supervised by a person who is responsible for

their safety or they have received instructions from such a person in how to use the equipment safely.

Children must always be supervised in order to ensure that they do not play with the equipment.

ozito-diy.co.uk

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

DECLARATION OF CONFORMITY

SERVICE INFORMATION

Please note that the following parts of this product are subject to normal or natural

wear and that the following parts are therefore also required for use as consumables.

* Not necessarily included in the scope of delivery!

SOUND & VIBRATION

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its

implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical

equipment must make sure that the equipment is properly disposed of if p1-he no longer wants to keep

the equipment. The old equipment can be returned to a suitable collection point that will dispose of

the equipment in accordance with the national recycling and waste disposal regulations. This does not

apply to any accessories or aids without electrical components supplied with the old equipment.

This consignment contains lithium-ion batteries.

In accordance with special provision 188 this consignment is not subject to the ADR regula-

tions. Handle with care. Danger of ignition in case of damage to the consignment package. If the

consignment package is damaged: Check and if necessary repackage. For further information contact:

0049 1807 10 20 20 66 (xed network 14 ct/min, mobile phone max. 42 ct/min) Outside Germany

charges will apply instead for a regular call to a landline number in Germany.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

Sound and vibration values were measured in accordance with EN 60745.

Lpa sound pressure level: 58.9 dB

pa uncertainty: 3 dB

Lwa

sound power level: 69.9 dB

wa uncertainty: 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions) determined in accordance with EN 60745.

Vibration emission value ah = 18.546 m/s2

K uncertainty = 1.5 m/s

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Caution! Residual risks

Even if you use this electric power tool in accordance with instructions,

certain residual risks cannot be rules out. The following hazards may arise

in connection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.

2. Damage to hearing if no suitable ear protection is used.

3. Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is

not properly guided and maintained.

Danger! Read the operating instructions to reduce the risk of inquiry.

Caution! Wear ear-muffs. The impact of noise can cause

damage to hearing.

Caution! Wear safety goggles. Sparks generated during

working or splinters, chips and dust emitted by the device can cause

loss of sight

Caution! Wear breathing mask. Dust which is injurious to

health can be generated when working on wood and other materials.

Never the device to work on materials containing asbestos!

WARRANTY

OZITO UK Champion’s Business Park, Unit 10, 1st Floor, Arrowe Brook Road, Upton, Wirral, Merseyside, CH49 0AB

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectication of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

Liu/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Cordless Buﬀ er Polisher PXBPS-254U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X 2011/65/EU

X 2006/42/EC

Annex IV

Noti ed Body:

Noti ed Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured LWA = dB (A); guaranteed L

WA = dB (A)

P = KW; L/Ø = cm

Noti ed Body:

2012/46/EU

Emission No.:

Standard references: EN 60745-1;

EN 60745-2-4; EN 55014-1; EN 55014-2

Landau/Isar, den 19.02.2018

First CE: 18 Archive-File/Record: NAPR018293

Art.-No.: 30.002.88 I.-No.: 11017 Alex KurzDocuments registrar:

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

DANGER! Read all safety regulations and instructions. Any errors made in following the safety

regulations and instructions may result in an electric shock, re and/or serious injury.

Keep all safety regulations and instructions in a safe place for future use. The term “electric tool” used

in the safety instructions refers to electric tools operated from the mains power supply (with a power cable) and to battery operated

electric tools (without a power cable).

1. Workplace safety

a) Keep your work area clean and well illuminated. Untidy or unlit work areas can result in accidents.

b) Do not operate the electric tool in an environment where there is a risk of explosions and where

there are inﬂammable liquids, gases or dust. Electric tools produce sparks which could set the dust or vapours alight.

c) Keep the electric tool out of the reach of children and other persons. If there is a distraction, you may lose

control of the appliance.

2. Electrical safety

a) The connector plug from this electric tool must ﬁt into the socket. The plug should never be

altered in any way. Never use adapter plugs together with earthed electric tools. Unaltered plugs and

correct sockets reduce the risk of an electric shock.

b) Avoid bodily contact with earthed surfaces such as pipes, heating, ovens and fridges. The risk of

electric shock is increased if your body is earthed.

c) Keep the tool out of the rain and away from moisture. The ingress of water into an electric tool increases the

risk of an electric shock.

d) Do not use the cable to carry the electric tool, to hang it up or to pull it out of the socket. Keep

the cable away from heat, oil, sharp edges and moving parts of the appliance. Damaged or entangled

cables increase the risk of an electric shock.

e) If you are working outdoors with an electric tool, only use extension cables which are designed

speciﬁcally for this purpose. Using specially designed outdoor extension cables, the risk of electric shock is reduced.

f) If operation of the electric tool in a damp environment can not be avoided, use a earth-leakage

circuit-breaker. The earthleakage circuit-breaker reduces the risk of an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and use an electric tool sensibly. Do not use the tool if

you are tired or under the inﬂuence of drugs, alcohol or medication. A moment of inattention when using the

electric tool can result in serious injuries.

b) Wear personal protection equipment and always wear safety goggles. Wearing personal protection (such

as dust masks, non-slip safety shoes, safety helmet or ear protection, depending upon the type and use of the electric tool) reduces the

risk of injury.

c) up accidentally. Ensure that the electric tool is switched off Make sure that the appliance cannot start

before you connect it to the power supply and/or insert the battery, or pick up or carry the tool. If

your nger is on the switch whilst carrying the electric tool or if you connect the appliance to the mains when it is switched on, this can

lead to accidents.

d) Remove keys and wrenches before switching on the electric tool. A tool or key which comes into contact

with rotating parts of the appliance can lead to injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep your balance at all

times. In this way, you can control the electric tool better in unexpected circumstances.

f) Wear suitable work clothes. Do not wear loose clothing or jewellery. Keep hair, clothes and

gloves away from moving parts. Loose clothing, jewellery or long hair can get trapped in moving parts.

g) If vacuuming devices and draining devices can be ﬁtted, make sure that these are correctly

attached and correctly used. The use of a dust extraction system can reduce the danger posed by dust.

4. Usage and treatment of the electric tool

a) Do not overload the appliance. Use the correct tool for your work. You will be able to work better and more

safely within the given performance boundaries.

b) Do not use an electric tool with a defective switch. An electric tool that cannot be switched on or off is dangerous

and must be repaired.

c) Pull the plug out of the socket and/or remove the battery before making any adjustments to the

appliance, changing accessories or put the appliance down. This safety measure prevents starting the electric

tool unintentionally.

d) Keep unused electric tools out of the reach of children. Do not allow people who are not familiar

with the appliance or who have not read these instructions to use the appliance. Electric tools are

dangerous if they are used by inexperienced people.

e) Clean your electric tool carefully. Check whether moving parts are functioning properly and not

jamming, whether parts are broken or damaged enough that the functioning of this electric tool

is affected. Have damaged parts repaired before using the appliance. Many accidents are caused by badly

maintained electric tools.

f) Keep your cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges will jam less and

are easier to control.

g) Make sure to use electric tools, accessories, attachments, etc. in accordance with these

instructions. Take the conditions in your work area and the job in hand into account. Using electric tools

for any purpose other than the one for which they are intended can lead to dangerous situations.

5. Using and handling the cordless tool

a) Only charge the batteries in chargers that are recommended by the manufacturer. A charger that is

designed for a certain type of battery may pose a  re risk if it is used with other types of battery.

b) Use only the correct batteries in the electric tools. The use of other batteries may result in injuries and a re risk.

c) Keep unused batteries away from paper clips, coins, keys, nails, screws and other metallic

objects that could cause a short circuit between the contacts. A short circuit between the battery contacts may

cause burns or a  re.

d) In case of incorrect use, ﬂuid may escape from the battery. Avoid contact with it. If you touch it

by accident, rinse the affected area with water. If you get the ﬂuid in your eyes, also seek medical

advice. Leaking battery uid can cause skin irritation or burns.

6. Service

a) Have your electric tool repaired only by trained personnel using only genuine spare parts. This will

ensure that your electric tool remains safe to use.

Additional safety instructions We pay a great deal of attention to the design of every battery pack to ensure that we supply

you with batteries which feature maximum power density, durability and safety. The battery cells have a wide range of safety devices.

Each individual cell is initially formatted and its electrical characteristic curves are recorded. These data are then used exclusively to

be able to assemble the best possible battery packs. Despite all the safety precautions, caution must always be

exercised when handling batteries. The following points must be obeyed at all times to ensure safe

use. Safe use can only be guaranteed if undamaged cells are used. Incorrect handling can cause

cell damage.

Important: Analyses conrm that incorrect use and poor care are the main causes of the damage caused by high performance

batteries.

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of ﬁre, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the charger to the mains supply make sure that the data on the rating plate are identical to the mains data.

This tools charger is double insulated; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for

added protection against injury resulting from a possible electrical insulation failure within the tool.

The power supply for this products charger should be protected by a residual current device (rated at 30mA or less). A residual current

device reduces the risk of electric shock.

Double insulated

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Polermaskine
Model:	PXBPS-254U

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito PXBPS-254U stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Polermaskine Ozito Manualer

Ozito PXBPS-254U Manual

6 August 2024

Ozito OZBP110WAU Manual

24 Juni 2023

Polermaskine Manualer

Nyeste Polermaskine Manualer

Tryton TMA1400 Manual

12 September 2024

Cocraft HP 110 Manual

8 September 2024

Black And Decker G650 Manual

6 September 2024

Powerplus POWPB40400 Manual

3 September 2024

Worx WX856.9 Manual

2 September 2024

Makita DPV300Z Manual

2 September 2024

Powerplus POWX0474 Manual

2 September 2024

Milwaukee AS 12 E Manual

1 September 2024

Robust RB-PO 110 Manual

31 August 2024

RIKON 31-200 Manual

31 August 2024