Palmer PLS-02 Manual

Palmer Splitter PLS-02

Læs nedenfor 📖 manual på dansk for Palmer PLS-02 (2 sider) i kategorien Splitter. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
PLS – Dual Channel Line Splitter02
SAFETY INFORMATION
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make cer-
tain that wall mounts are properly installed and secured. Make certain that the equipment is installed
securely and cannot fall down.
7. During installation, observe the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat.
Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor
equipment - in this case, observe the special instructions noted below. Do not expose this equipment
to flammable materials, fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers
filled with liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by the manufacturer.
15. Open the device for changing the battery, do not modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due
to tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause property
damage and personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equip-
ment or if it has been damaged in another way, switch it off immediately and unplug it from the
mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified
personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please sep-
arate plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
22. If the equipment has been exposed to strong fluctuations in temperature (for example, after trans-
port), do not switch it on immediately. Moisture and condensation could damage the equipment. Do
not switch on the equipment until it has reached room temperature.
23. Do not step on the power cord. Make certain that the power cable does not become kinked, especially
at the mains outlet and/or power adapter and the equipment connector.
24. When connecting the equipment, make certain that the power cord or power adapter is always freely
accessible. Always disconnect the equipment from the power supply if the equipment is not in use
or if you want to clean the equipment. Always unplug the power cord and power adapter from the
power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and
power adapter with wet hands.
25. To disconnect the equipment from the power mains completely, unplug the power cord or power
adapter from the power outlet.
26. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike
or before extended periods of disuse.
CAUTION:
CAU T I O N
RIS K OF SELE CTRI C HOCK
DO N O NOT PE
There are no user serviceable parts inside. Have repairs carried out only by qualified service personnel.
CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore, commercial use of this equipment is subject
to the respectively applicable national accident prevention rules and regulations. As a manufacturer, Adam
Hall is obligated to notify you formally about the existence of potential health risks. Hearing damage due to
high volume and prolonged exposure: When in use, this product is capable of producing high sound-pres-
sure levels (SPL) that can lead to irreversible hearing damage in performers, employees, and audience
members. For this reason, avoid prolonged exposure to volumes in excess of 90 dB.
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
You can find our current warranty conditions and limitation of liability at: http://www.adamhall.com/media/
shop/downloads/documents/manufacturersdeclarations.pdf
To request warranty service for a product, please contact Adam Hall GmbH, Daimler Straße 9, 61267 Neu
Anspach / Email Info@adamhall.com / 49 (0) 6081 / 9419-0
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance
may not be treated as household waste. This is to avoid environmental damage or personal injury due
to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it
recycled to promote sustainable economic activity.
SCOPE OF APPLICATION
The PLS02 is a passive, 2-channel line splitter. Such splitters are generally used to distribute one line
signal to numerous outputs. For example, the PLS02 can be used to split the master L/R out- put of a
mixer out to different amplifiers. The rear outputs of the PLS02 are transformer isolated so there is no
risk of ground loop, even if the amplifiers are connected to different electric circuits. In the case of using
unbalanced signals, then a bridge must be soldered between pin1 and pin 3 of the XLR connector. pin 2
is then hot. If pin 3 needs to be hot then pin 1 and pin 2 must be bridged.
TECHNICAL SPECIFICATIONS
Product Type: Splitter
Type: Line Split
Split type: 1 in 2 + 1
Channels: 2
Inputs: 2
Input Connectors: XLR
Max. Input Level: + 20 dB
Number of Split-Outputs per Canal: 2
THRU Outputs / Channel: 1
Max. Output Level: + 20 dB
Output Connectors: XLR
Transformer Isolated Outputs: Yes
Controls: Ground Lift
Cabinet Material: Die-cast Aluminium
Cabinet Surface: Powder Coated
Width: 95 mm
Depth: 120 mm
Height: 55 mm
Weight: 0.74 kg
© Palmer Musical Instruments, Adam Hall GmbH, D-61267 Neu-Anspach, Daimlerstr. 9, Germany TEL: ++49 (0)6081 94190
FAX: ++49 (0)6081 43280 WEB: www.adamhall.com, www.palmer-germany.com EMAIL: info@palmer-germany.com


Produkt Specifikationer

Mærke: Palmer
Kategori: Splitter
Model: PLS-02

Har du brug for hjælp?

Hvis du har brug for hjælp til Palmer PLS-02 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Splitter Palmer Manualer

Palmer

Palmer PLS-02 Manual

12 November 2024

Splitter Manualer

Nyeste Splitter Manualer

Fujitsu

Fujitsu ASYG14LUCA Manual

3 Oktober 2024
Fujitsu

Fujitsu ECO ASHG18KLCA Manual

29 September 2024
D-Link

D-Link DPE-301GS Manual

28 September 2024
Audio-Technica

Audio-Technica ATW-49SP Manual

27 September 2024
IFM

IFM EBC113 Manual

24 September 2024
Fujitsu

Fujitsu ASHG09LTCA Manual

19 September 2024
Fujitsu

Fujitsu ARYG60LHTA Manual

17 September 2024