Penton RCS5FTCX/EN Manual

Penton Speaker RCS5FTCX/EN

Læs nedenfor 📖 manual på dansk for Penton RCS5FTCX/EN (1 sider) i kategorien Speaker. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
RoHS
Penton UK Ltd
Unit 2 Teville Industrials Dominion Way Worthing West Sussex | | | | BN14 8NW
T: +44 (0)1903 215315 F: +44(0)1903 215415 E: sales@ pentonuk.co.uk | |
www.pentonuk.co.uk
1. LOUDSPEAKER
ENCLOSURE
2. REFERENCE AXIS
3. REFERENCE PLANE
4. HORIZONTAL PLANE
ROUND METAL CEILING
LOUDSPEAKERS
f RCS5FTCX/EN
f RCS5FTCX/ENC
EN54-24
INSTALLATION INSTRUCTIONS
EN54-24:2008
Certificate No: 0359-CPD-0120 TYPE A
Circuit Diagram
f RCS5FTCX/EN
f RCS5FTCX/ENC
* with capacitor
I IA
Slide
I ID
D
D
D
D
C
B
1. Remove the wing nut “A” located on
the inside of the fire dome.
FITTING THE DOME INTO A CEILING
6. Cut a 164mm diameter hole paying attention to ensure that the cut-out is
accurately made. As if it is not, the speaker may not fit correctly into the ceiling
preventing the speaker from sitting flush to the surface.
7. Loosen the slider knob “D”, push the knob & plate upwards to the top of the fire
dome and re-tighten the knob to hold the slider in place. Repeat the same process
with the other slider.
8. Push the complete fire dome into the cut-out.
9. Once in place loosen the slider knob “D”, push the knob & plate downwards
until the slider makes firm contact with the ceiling. Tighten the knob to secure it into
place. Repeat the same process with the other slider.
10. The fire dome should be firmly
secured into the ceiling.
11. Take the speaker and
compress one of the mounting springs
& place both ends of the spring into
one of the retaining brackets located
on the inside wall of the fire dome.
Release the spring slowly into the
bracket. Once fully released the
spring will hold one side of the
speaker into the fire dome.
12. With the speaker in this position
connect the 3 wires hanging from the
termination plate on to the speaker using
the spade terminals provided.
13. Fit the second spring mount on
the speaker to the remaining bracket on
the inside of the fire dome. Finally push
the speaker into position.
14. If fitted correctly the speaker
should fit flush to the surface.
2. Lift the termination plate upwards
& away to separate it from the fire
dome “B”.
3. Gland the installation cable into the termination plate using
suitably rated 20mm glands. 2 gland entries are provided for
“loop in” “loop out” termination if required.
4. Terminate the installation cable into the terminal block on
the underside of the termination plate “C”.
5. Fix the termination plate back into the fire dome and secure
using the wing nut previously removed. Do not over tighten to
avoid damaging the thread.
4
3
2
1
ZCL0504-060/061
OCTOBER 2011
COMMON
*
10W
5W
2.5W
1.25W


Produkt Specifikationer

Mærke: Penton
Kategori: Speaker
Model: RCS5FTCX/EN

Har du brug for hjælp?

Hvis du har brug for hjælp til Penton RCS5FTCX/EN stil et spørgsmål nedenfor, og andre brugere vil svare dig




Speaker Penton Manualer

Penton

Penton RCS8FT/EN Manual

23 August 2024
Penton

Penton RCS5FTCX/EN Manual

23 August 2024
Penton

Penton RCS6FT/EN Manual

23 August 2024
Penton

Penton MSH30T/EN Manual

23 August 2024
Penton

Penton PBC6T/EN Manual

23 August 2024
Penton

Penton CELL20T/EN Manual

23 August 2024
Penton

Penton CAD10T/EN Manual

23 August 2024
Penton

Penton CELL10T/EN Manual

23 August 2024

Speaker Manualer

Nyeste Speaker Manualer

OSD Audio

OSD Audio ICE630ST Manual

18 September 2024
OSD Audio

OSD Audio LS2 Manual

18 September 2024
TOA

TOA PC-2668 Manual

18 September 2024
TOA

TOA PC-3WR-L Manual

18 September 2024
TOA

TOA BS-1120W Manual

18 September 2024
TOA

TOA TZ-105 Manual

18 September 2024
TOA

TOA BS-1110W Manual

18 September 2024
Anchor Audio

Anchor Audio AN-130U1BK Manual

18 September 2024
Teufel

Teufel Consono 15 Manual

18 September 2024