Quoizel PCSO8532C Manual

Quoizel Lys PCSO8532C

Læs nedenfor 📖 manual på dansk for Quoizel PCSO8532C (2 sider) i kategorien Lys. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Package Contents
Please go to for product cleaning tips. Go to the selection.
: Lutron AYCL-153P or Lutron DVCL-153P.
www.quoizel.com Care + Maintenance
Compatible Dimmer Switches
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source:
Estimated Assembly Time:
Preparation:
Integrated LED 53W
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PCSO8532C
For Style PCSO8532C
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
B
Mounting
Screw
x 4
Inner Backplate
x 1
STEP 2 Install Inner Backplate-
A. Pass the supply wires and ground wire through the Inner
Backplate (A). Attach the Inner Backplate (A) to Outlet Box with
the head of Green Ground Screw facing you. Secure it with Outlet
Box Screws (not included). Tighten until snug.
A
DFixture Body
x 1
C
Figure 2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-10-12
Glass Panel
x 1 A
Outlet Box
Outlet Box Screw
(not supplied)
Supply Wires and
Ground Wire
Figure 1
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Lock Screw
STEP 1 Install Glass Panel to Fixture Body-
A. Place the Fixture Body (D) onto a flat working surface. Unlock lock
screws from the back of the Fixture Body (D) and remove the glass
holder on both ends.
B. Remove lock nuts and rubber washers from glass holders. Attach
the Glass Panel (C) to the bolts on glass holders with the beveled
edge against the bolt side of the glass holders. Secure by threading
rubber washers and lock nuts back onto bolts. Hand tighten until
snug.
C. Attach glass holders back onto the Fixture Body (D) and secure with
previously removed lock screws. Tight until snug with screwdrivers.
Rubber Washer
Lock Nut
Bolt
Beveled Edge Glass Holder
D
C


Produkt Specifikationer

Mærke: Quoizel
Kategori: Lys
Model: PCSO8532C

Har du brug for hjælp?

Hvis du har brug for hjælp til Quoizel PCSO8532C stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys Quoizel Manualer

Lys Manualer

Nyeste Lys Manualer