RCA RCR313BE Manual
Læs nedenfor 📖 manual på dansk for RCA RCR313BE (4 sider) i kategorien Joystick. Denne guide var nyttig for 132 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/4
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Industry Canada Regulatory Information
CAN ICES-3 (B)/NMB-3 (B)
Avis d’Industrie Canada
CAN ICES-3 (B)/NMB-3 (B)
• There is a possibility that a programmed code may only be
able to control some of your device features (for example, only
turns a device on and off). To conrm that the device key is
programmed with the correct code for maximum functionality,
test the device. Attempt to control a variety of the device’s
functions with the remote. If some of the features of your
devices don’t work, try programming the remote with a
different code in the list using the Direct Code Entry Method,
until you nd the code that allows the remote to control the
majority of your device’s functions. Different codes can provide
different levels of functionality.
Problem: The key does not light when you press a POWER
key.
• You may have pressed an invalid key for the mode the remote is
in.
• Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STREAM DVD•VCR, ).
This tells the remote which device to operate.
• Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AA batteries, if necessary
(see the Battery Installation section).
Problem: The remote will not change channels on device.
• Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STREAM DVD•VCR, ).
This tells the remote which device to operate.
• Press the OK key after you enter a channel number.
• Remove any obstacles between the remote and the device.
Make sure to aim the remote at the IR sensor on the device.
Problem: The device’s menu does not appear on the TV
screen.
• Make sure you have connected the device to your TV properly
and selected the correct input. (See your devices’ Owner’s
Manuals for proper connection procedures.)
• Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STREAM DVD•VCR, ).
This tells the remote which device to operate.
• Menu access isn’t supported for all brands. You may need to
use your original remote control to access menu functions for
some devices.
For more information, including instructional
videos, remote programming codes, and customer
support, visit www.RCACodeSupport.com
In most cases, the keys on
this remote perform the
same functions as the keys
on your original remotes
once you’ve programmed
this remote to operate your
components. Many keys
on this remote have other
functions as well.
Illuminated POWER key
serves as an indicator light
to provide feedback.
Device keys (TV,
SAT•CBL•STREAM,
DVD•VCR) put the remote
in the right mode to control
your device.
LIGHT key ( ) turns
backlighting on/off.
GUIDE/HOME MENU and
access the same features
as the keys on your original
remotes.
Arrow keys act as
navigation keys for
streaming media players as
well as in menu and guide
systems for other devices.
Battery Saver
Your universal remote control saves battery power by
automatically turning off if any key is pressed for more than
60 seconds. This saves your battery life should your remote
get stuck in a place where the keys remain depressed, such as
between sofa cushions.
Congratulations on your purchase of this 3-device RCA Universal
Remote Control. This remote features a library of codes with the
latest devices of all major brands, with support for streaming
media players as well. The navigation keys have been redesigned
to function seamlessly with the more sophisticated menu and
guide systems found in today’s home entertainment devices.
Universal Remote Control
Owner’s Manual
RCR314WE / RCR313BE
Manual del Propietario (parte posterior)
Care and Maintenance
• Keep the remote dry. If it gets wet, wipe it dry immediately.
• Use and store the remote only in normal temperature
environments.
• Handle the remote gently and carefully. Don’t drop it.
• Keep the remote away from dust and dirt.
• Wipe the remote with a damp cloth occasionally to keep it
looking new.
• Modifying or tampering with the remote’s internal devices
can cause malfunction and invalidate its warranty.
SAVE THIS MANUAL AND THE CODE LISTS!
Remote controls can sometimes lose their programming when you
change the batteries. Make sure you keep the manual and code lists
in a safe place so that you can reprogram the remote if you need to.
Your universal remote requires two AA alkaline batteries
(batteries may or may not be included, depending on model).
To install the batteries:
1. Remove the battery compartment
cover.
2. Insert the batteries, matching the
batteries to the (+) and (–) marks
inside the battery compartment.
3. Push the battery cover back into
place.
Battery Precautions:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly
and recycle or dispose of them in accordance with Local and
National Regulations.
To use this universal remote with your home entertainment
system, rst you need to program it to control your devices.
There are four ways you can program the universal remote to
operate your devices. Try them in the order listed here:
• The lets you enter a code from the Direct Code Entry
accompanying code list for your brand of device.
• The searches through the codes for Brand Code Search
select brands of devices.
• The Auto Code Search goes automatically through all the
codes for the device you’re trying to control.
• The lets you manually go through all Manual Code Search
the codes for the device you’re trying to control.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote. If
some device features don’t work, go to the next step to
try a different code.
2. Repeat the Brand Code Search from the beginning.
When the device turns off for the rst time, don’t press
the STOP key, which would store the same code. Instead,
with the unit now off, continue to press the POWER key
repeatedly until the unit turns back on.
3. Once the unit turns back on, you have found another
code that operates the device. Press the STOP key.
4. Test the key’s functionality again by attempting to
control a variety of the device’s functions. If the code
that has been stored controls the majority of the device’s
functions, programming is complete. If the code stored
does not give maximum functionality, try another code.
Brand Code Search
The Brand Code Search goes through only the codes for one of
the select brands listed in the accompanying code list. If your
brand of device is listed, this search can be very quick and easy.
TIPS: Each device key is associated with a type of device—the
TV is preset to search for TVs, SAT•CBL•STREAM for satellite
receivers, cable boxes, digital TV converters, or streaming
media players and DVD•VCR for VCRs or DVD players.
The POWER key serves as an indicator light during
programming, giving you feedback at each stage of the
process.
To exit without saving a new code at any point in the Brand
Code Search, press the key.GO BACK
1. Manually turn on the device you
want to control.
4. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand
to press and hold the remote’s POWER key at the same
time.
5. Wait until the POWER key comes on and stays on. Then
release both keys.
7. Point the remote directly at the front
panel of the device you want to
control. Press on the remote POWER
and wait 2 seconds. The remote is
testing a single code for your device’s
brand.
Did your device turn off?
YES: Press the STOP key to store the code. You’re done!
You’ve programmed this device key.
NO: Press again. The remote tests the next code POWER
for your brand.
Keep pressing every 2 seconds until your device POWER
turns off. When it does, press STOP.
3. Find your device’s brand in the
Brand Code list section of the
accompanying code list. Circle the
number for your brand and keep
the list handy.
Code Lists
Brand Codes are us e d for programming us ing the Brand Code Sea rch
and Entry me thod outlined in the Us er’s Guide.
List a de Códigos
Los códigos de las ma rcas s on utilizados para programa r utilizando
los método s de bús que da y entr ada de códigos de marcas , es a ltado r
en la guía del us uario.
0
1
2 3
4
5 6
789
RCA
GE
PROSCAN
Insignia JVC M agn avo x
Philip s Panason ic Samsun g Sharp S ony Toshiba Vizio
T V
VCR
0
1
2 3
4
5 6
789
RCA
GE
PROSCAN
A pex JVC Ma gna vo x
Philip s Panason ic Pion eer S amsung S harp ToshibaSony
DVD
S AT /C ABLE
0
1
2 3
4
5 6
789
RCA
GE
PROSCAN
Motoro la DirecTV
Dish Network
Systems/
Echostar
General
Instruments
Hughes
Network
System s Scientifi c
Atlanta M agn avo x
Philip s AMNIO
ADB Panaso nic
Br and Cod e List/Li sta de Có dig os de Mar ca s
0
1
2 3
4
5 6
789
Samsun g
Magn avo x
Philip s Mitsubish i Pan ason ic Sharp S ony Toshiba
RCA
GE
PROSCA N
JVC Symp honic
6. Look at the number you circled for your
device’s brand code number. Press that
number on the remote keypad.
NOTES
Throughout the programming of each key, be sure to keep
the remote pointed at the IR sensor of the device you are
currently programming the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don’t work, try a
different code. See the “Testing the Code for Maximum
Functionality” section below for more information.
During the Brand Code Search, the remote ignores
keypresses that aren’t part of the search.
The search times out after two minutes (the key POWER
blinks four times and turns off, and the last programmed
code under that device key is retained).
The key blinks four times and turns off when the POWER
remote has gone through all the codes. The remote exits
the Brand Code Search. If your device hasn’t turned off yet,
try a different search method.
Direct Code Entry
Direct Code Entry lets you enter a code from the
accompanying code list for your brand of device.
1. Manually turn on the device you
want to control.
3. Press and hold the device key you want to program (the
POWER key comes on).
While you’re holding down the device key, use your other
hand enter the rst ve-digit code for your brand in the
code list (the POWER key goes off after the rst digit).
2. Find the Code List that came with
the remote. Locate the section for
the type of device you’re trying to
program, and nd your brand in that
section. Circle the codes for your
brand and keep them handy.
Co de List s
Brand Codes are used for programming using the Brand Code Search
and Entry method outlined in the User’s Guide.
Lista de Có digo s
Los códigos de las marcas son utilizados para programar utilizando
los métodos de búsqueda y entrada de códigos de marcas, esaltado r
en la guía del usuario.
0
1
2 3
4
5 6
789
RCA
GE
PROSCAN
Insign ia JVC Ma gn avox
Phil ips Pana soni c Samsun g Sharp Sony Tosh iba Vi zio
TV
VCR
0
1
2 3
4
5 6
789
RCA
GE
PROSCAN
Apex JVC M ag na vox
Phil ips Pana so ni c Pion eer Sam su ng Sharp Tosh ib aSony
DVD
SAT/CAB LE
0
1
2 3
4
5 6
789
RCA
GE
PROSCAN
Moto rol a DirecTV
Dish Network
Systems/
Echostar
General
Instruments
Hughes
Network
Systems
Scientific
Atlan ta
Mag na vox
Phil ips AM NIO
ADB Pan ason ic
Brand Code Lis t/Lista de Códigos de Marcas
0
1
2 3
4
5 6
789
Samsung Mag na vox
Phil ips
Mitsubi shi P an aso ni c Sharp Sony To shib a
RCA
GE
PROSCAN
JVC
Symph on i c
NOTES
Remember to enter the code for future reference in the box
provided in the Code Retrieval section of this manual.
If your brand isn’t listed in the code list, use one of the Code
Search methods to program the remote control. (Refer to
the Auto and Manual Code Search methods.)
If you release the device key any time during the Direct
Code Entry procedure, the key blinks four times, POWER
and the process is exited. The last programmed code under
the device key is retained.
Test the remote with the device to make sure the device
key is programmed with the correct code for maximum
functionality. If some features don’t work, try a different code
in the list.
4. When you’ve nished entering the ve-digit code, keep
holding down the device key and look at the POWER key.
Is the POWER key on?
YES: You’re done! You’ve programmed this device key.
NO, it blinked four times and turned off: You have
either entered a code number that is not in the code lists
or missed a step in the code entry procedure. Try step 3
again.
1. Manually turn on the device you want
to control.
2. If you’re programming the TV or SAT•CBL• key,STREAM
go to step 3.
If you’re programming the key,DVD•VCR you need to
tell the remote which kind of device you want this key to
control, VCR or DVD.
Press and hold the DVD•VCR key. While you’re holding
down the DVD•VCR key, use your other hand to press the
number key for the type of device you want to control
with this key: 2 for VCR, 3 for DVD.
4. Wait until the POWER key comes on and stays on. Then
release both keys.
5. Point the remote directly at the front panel of the device you
want to control. Press on the remote and wait 2 POWER
seconds. The remote is testing a single code for your device.
Did your device turn off?
YES: Press the STOP key to store
the code. You’re done! You’ve
programmed this device key.
NO: Press again. The POWER
remote tests the next code for your
device.
Keep pressing POWER every 2
seconds until your device turns off.
When it does, press STOP.
TIP: Because there are so many codes, you may have to
press the key many times—possibly hundreds of POWER
times.
NOTES
Throughout the programming of each key, keep the remote
pointed at the IR sensor of the device you are programming
the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don’t work, try a
different code. See the “Testing the Code for Maximum
Functionality” section below for more information.
During the Manual Code Search, the remote ignores
keypresses that aren’t part of the search.
The search times out after two minutes (the key POWER
blinks four times and turns off, and the last programmed
code under that device key is retained).
The key blinks four times and turns off when the POWER
remote has gone through all the codes. The remote exits
the Manual Code Search. If your device hasn’t turned off
yet, try a different search method.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote. If
some features of your devices don’t work, go to the next
step to try a different code.
2. Repeat the Manual Code Search from the beginning.
When the device turns off for the rst time, don’t press
the STOP key, which would store the same code. Instead,
with the unit now off, continue to press the POWER key
repeatedly until the unit turns back on.
3. Once the unit turns back on, you have found another
code that operates the device. Press the STOP key.
4. Test the key’s functionality again by trying a variety of
functions. If the code controls the majority of the device’s
functions, programming is complete. If the code stored
does not give maximum functionality, try another code.
Code Retrieval
Once you’ve programmed the remote to control your devices,
you may want to record the codes for future reference. If
you used the Direct Code Entry method, this is easy. Just
nd the codes you entered and make a note of them in the
boxes below. If you used one of the Code Search methods to
program your remote or if you used the Direct Entry method
but don’t remember the code, you will need to retrieve each
device’s ve-digit code. Retrieving the actual code and writing
it down will save you time if you ever need to program the
remote again (e.g., if programming is lost when you change
the batteries). If the codes are recorded, you can use the
Direct Entry method to reprogram your remote to control your
devices, which is quick and easy.
1. Press and hold the device
key (TV, SAT•CBL•STREAM,
DVD•VCR) whose code you
wish to retrieve. The POWER
key turns on. Keep pressing
the device key.
IMPORTANT
Because this remote controls more than one device, you
must rst “tell” the remote which device you wish to
operate. That means, if you wish to operate your TV, you
must rst press the TV key to put the remote in the TV
Mode. The remote stays in that device mode until you
press a different device key. For example, if your remote is
in TV Mode and you want to operate the DVD player, you
must press the DVD•VCR key to change device modes.
Problem: The remote does not operate your device.
• Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STREAM DVD•VCR, ).
This tells the remote which device to operate.
• Remove any obstacles between the remote and the device.
Make sure you’re aiming the remote at the device’s IR sensor.
• Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AA batteries, if necessary
(see the Battery Installation section).
Problem: The remote can’t be programmed to operate
your device.
• If you are testing the remote while programming it, you may be
too far away from the device or at a wrong angle. There must
be an unobstructed path between the remote and the IR sensor
on the device. Move closer and make sure you point the remote
at the device you’re trying to control.
• If you’re using the Direct Entry programming method to enter
the codes for your brand and the unit is still not functioning
properly, try the auto, brand, or manual search method.
• To control combo units, like TV/VCRs or TV/DVDs, you must
program the individual corresponding device keys to control
each part of the combo unit. Once programmed successfully,
the TV key controls the TV functions, and the key DVD•VCR
controls the VCR or DVD functions.
• Make sure the batteries are fresh and are properly installed.
Problem: The remote doesn’t perform commands properly.
• Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STREAM DVD•VCR, ).
This tells the remote which device to operate.
• Make sure device is ready (for example, the DVD player has a
disc loaded).
• You may have pressed an invalid key for the mode the remote is in.
• If you’re trying to enter a channel number directly, try pressing
the OK key after entering the channel number as this is a
requirement of certain models and brands.
Voxx Accessories Corporation (the “Company”) warrants to you the
original retail purchaser of this product that should it, under normal use
and conditions, be proven defective in material or workmanship during its
lifetime while you own it, such defect(s) will be repaired or replaced (at the
Company’s option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of the warranty, the product
is to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specication of defect(s), transportation prepaid, to an approved warranty
station. For the location of the nearest warranty station to you, call toll-free to
our control ofce: 1-800-645-4994.
This Warranty does not cover product purchased, serviced or used outside
the United States or Canada. This Warranty is not transferable and does
not extend to costs incurred for installation, removal or reinstallation of
the product. This Warranty does not apply if in the Company’s opinion,
the product has been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or the simultaneous use of different
battery types (e.g. alkaline, standard or rechargeable).
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN
NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE
PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL
BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL
THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES WHATSOEVER. No person or representative is authorized
to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you. This
Warranty gives you specic legal rights and you may also have other rights,
which vary from state/province to state/province.
Trademark(s) ® Registered
©2018 Voxx Accessories Corp.
3502 Woodview Trace, Suite 220
Indianapolis, IN 46268
Step 1: Install your batteries
Step 2: Program your remote
Tour of the Remote Advanced Functions
Troubleshooting
Limited Lifetime Warranty
POWER key
2. If you’re programming the TV or SAT•CBL• key,STREAM
go to step 3.
If you’re programming the key,DVD•VCR you need to
tell the remote which kind of device you want this key to
control, VCR or DVD.
Press and hold the DVD•VCR key. While you’re holding
down the DVD•VCR key, use your other hand to press the
number key for the type of device you want to control
with this key: 2 for VCR, 3 for DVD.
3. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand to
press and hold the remote’s POWER key at the same time.
Note: All TV codes begin with the number 1; all VCR and
DVR codes begin with the number 2; all DVDs, the number
3; and all satellite receivers, cable boxes, streaming players,
and DTV converters, the number 5.
5. Repeat step 4 until you have retrieved all ve numbers in
the code. After the fth number is retrieved, the POWER
key blinks briey, then turns off.
TIP: To exit the Code Retrieval Mode at any time, press the
GO BACK key.
Note: If you press an invalid key during the Code Retrieval
process, the remote will not respond. If you do not press a
valid Code Retrieval key (TV, SAT•CBL• , , STREAM DVD•VCR
INFO-OPTIONS, GO BACK), Code Retrieval times out after
15 seconds. The key blinks four times, and then POWER
turns off.
CHAN VOL and keys act as channel and volume controllers.
The CHAN keys also provide skip forward and skip back
control for DVD players and DVRs that support this
functionality.
GO BACK exits remote programming; it also performs the
same functions as on your original remotes.
The and INPUT — (dash) key has three functions: (1) it toggles
through all the video sources connected to your TV; (2) when
the remote is in VCR mode, this button toggles between VCR
and the TV input; (3) when you’re entering digital channel
numbers directly, this button lets you separate the main
channel number from the sub-channel number (such as 59.1).
Backlighting
Backlight illumination helps you see the remote control keys
better in the dark. You can turn backlight illumination on by
pressing the LIGHT key ( ). Backlighting stays on as long as
keys are being pressed and turns off ve seconds after the last
keypress.
2. While holding the device key down, press and hold the
INFO-OPTIONS key. The key turns off. After POWER
holding down both keys for three seconds, the POWER
key turns back on.
3. Release both keys. The key remains on.POWER
4. Starting with the number 1 key, press and release each
number key on the keypad in the following order: 1-9,
then 0. The number that causes the POWER key to blink is
the rst number of the code. As you nd each number of
the code, write it down for future reference.
TIP: Each device key is associated with a type of device—the
TV is preset to search for TVs, SAT•CBL•STREAM for satellite
receivers, cable boxes, digital TV converters, or streaming
media players, and DVD•VCR for VCRs or DVD players.
The POWER key serves as an indicator light during
programming, giving you feedback at each stage of the
process.
Auto Code Search
The Auto Code Search goes automatically through all the
codes for the device you’re trying to control. When you nd
the one that operates your device, you can stop the search
and store that code.
TIPS: Each device key is associated with a type of device—
the TV is preset to search for TVs, SAT•CBL•STREAM for
satellite receivers, cable boxes, digital TV converters, or
streaming media players, and DVD•VCR for VCRs or DVD
players.
To exit without saving a new code at any point in the Auto
Code Search, press the key.GO BACK
1. Manually turn on the device you
want to control.
3. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand
to press and hold the remote’s POWER key at the same
time.
2. If you’re programming the TV or SAT•CBL• key,STREAM
go to step 3.
If you’re programming the key,DVD•VCR you need to
tell the remote which kind of device you want this key to
control, VCR or DVD.
Press and hold the DVD•VCR key. While you’re holding
down the DVD•VCR key, use your other hand to press the
number key for the type of device you want to control
with this key: 2 for VCR, 3 for DVD.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote. If
some device features don’t work, go to next step to try a
different code.
2. Repeat the Auto Code Search Method from the
beginning. When your device turns off, do not stop
searching. Instead, with the unit now off, continue to
press the PLAY key every 5 seconds until the unit turns
back on.
3. Once the unit turns back on, press the REVERSE key on
the remote every 2 seconds until your device turns off
again. When your device turns off again, press the STOP
key.
4. Test the key’s functionality again by attempting to
control a variety of the device’s functions. If the code
that has been stored controls the majority of the device’s
functions, programming is complete. If the code stored
does not give maximum functionality, try another code.
4. Wait until the POWER comes on and stays on. Then key
release both keys.
5. Point the remote directly at the
front panel of the device you want
to control. Press PLAY on the
remote and wait 5 seconds. The
remote is testing a batch of 10
codes on your device.
Did your device turn off?
YES: Go to step 6.
NO: Press PLAY again. The remote tests the next batch of
10 codes.
Keep pressing PLAY every 5 seconds until your device turns
off.
6. When your device turns off, press
the REVERSE key on the remote
and wait at least 2 seconds. The
remote tries the last of the previous
ten codes.
Did your device turn on?
YES: Press the STOP key. You’re
done! You’ve programmed this
device key.
NO: Press REVERSE again. The remote tests the next
code in the batch.
Keep pressing REVERSE every 2 seconds until your device
turns back on. When it does, press STOP.
Note: If you accidentally press the REVERSE key after your
device turns on, press the FORWARD key. Then, wait two
seconds to see if your device turns off again.
NOTES
Throughout the programming of each key, be sure to keep
the remote pointed at the IR sensor of the device you are
currently programming the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don’t work, try a
different code. See the “Testing the Code for Maximum
Functionality” section below for more information.
During the Auto Code Search, the remote ignores
keypresses that aren’t part of the search.
The search times out after two minutes (the key POWER
blinks four times and turns off, and the last programmed
code under that device key is retained).
The key blinks four times and turns off when the POWER
remote has gone through all the codes. The remote exits
the Auto Code Search. If your device hasn’t turned off yet,
try a different search method.
Manual Code Search
The Manual Code Search lets you go one-by-one through all the
codes for the device you’re trying to control. When you nd the
one that operates your device, you can stop the search and store
that code.
Actual model may vary from
illustration
TIPS: Each device key is associated with a type of device—the
TV is preset to search for TVs, SAT•CBL•STREAM for satellite
receivers, cable boxes, digital TV converters, or streaming
media players, and DVD•VCR for VCRs or DVD players.
The POWER key serves as an indicator light during
programming, giving you feedback at each stage of the
process.
The Manual Code Search method may take a long time
because the remote searches through all of the codes in its
memory one-by-one. If your brand is listed in the Brand Codes
or the Code Lists, rst try the Brand Code Search or the Direct
Code Entry method.
To exit without saving a new code at any point in the Manual
Code Search, press the GO BACK key.
DVD•VCR CODE
DVD VCR
1
TV CODE
5
SAT•CBL•STREAM CODE
SAT CABLE DTV CONVERTER
STREAMING PLAYER
RCR314WE US 01 2597
Produkt Specifikationer
| Mærke: | RCA |
| Kategori: | Joystick |
| Model: | RCR313BE |
Har du brug for hjælp?
Hvis du har brug for hjælp til RCA RCR313BE stil et spørgsmål nedenfor, og andre brugere vil svare dig
Joystick RCA Manualer
2 Maj 2024
25 Februar 2024
23 November 2023
31 Juli 2023
1 Juli 2023
17 December 2022
1 December 2022
18 November 2022
15 November 2022
Joystick Manualer
- Joystick Sony
- Joystick Aruba
- Joystick Panasonic
- Joystick Philips
- Joystick Nintendo
- Joystick Pioneer
- Joystick TOA
- Joystick Carat
- Joystick Logitech
- Joystick Behringer
- Joystick HP
- Joystick Carel
- Joystick Roland
- Joystick Asus
- Joystick Pyle
- Joystick Tracer
- Joystick Denon
- Joystick One For All
- Joystick Yamaha
- Joystick Nedis
- Joystick Da-Lite
- Joystick Hama
- Joystick Thomson
- Joystick Belkin
- Joystick JBL
- Joystick AKAI
- Joystick DataVideo
- Joystick Trust
- Joystick Honeywell
- Joystick Razer
- Joystick Speedlink
- Joystick Tangent
- Joystick Cisco
- Joystick Huawei
- Joystick König
- Joystick Gembird
- Joystick Bose
- Joystick Netgear
- Joystick Parrot
- Joystick Danfoss
- Joystick Tripp Lite
- Joystick Mad Catz
- Joystick Microsoft
- Joystick Vaddio
- Joystick SteelSeries
- Joystick Thrustmaster
- Joystick Genesis
- Joystick Krüger&Matz
- Joystick Dell
- Joystick Schneider
- Joystick DJI
- Joystick Cooler Master
- Joystick PreSonus
- Joystick MSI
- Joystick Ikan
- Joystick Irritrol
- Joystick Rain Bird
- Joystick Tascam
- Joystick Datalogic
- Joystick Velleman
- Joystick Marshall
- Joystick Sonance
- Joystick Zoom
- Joystick JUNG
- Joystick Fostex
- Joystick HQ Power
- Joystick Teac
- Joystick Sven
- Joystick Thermaltake
- Joystick SBS
- Joystick ART
- Joystick Monacor
- Joystick ION
- Joystick Spektrum
- Joystick Numark
- Joystick Keith MCmillen
- Joystick Chamberlain
- Joystick DBX
- Joystick Jumbo
- Joystick Asustor
- Joystick Aquatic AV
- Joystick IK Multimedia
- Joystick Saitek
- Joystick Nyko
- Joystick Senal
- Joystick Movistar
- Joystick Xantech
- Joystick Krom
- Joystick Contour Design
- Joystick Oculus VR
- Joystick L-Link
- Joystick Chauvet
- Joystick 8BitDo
- Joystick Crestron
- Joystick Kogan
- Joystick RGBlink
- Joystick Inovonics
- Joystick Hitec
- Joystick Nektar
- Joystick GMB Gaming
- Joystick Bigben
- Joystick Ewent
- Joystick Auray
- Joystick Gamesir
- Joystick PDP
- Joystick Ltech
- Joystick Logic3
- Joystick Gioteck
- Joystick Steca
- Joystick Icon
- Joystick Highpoint
- Joystick IVT
- Joystick Dragonshock
- Joystick PCE Instruments
- Joystick COLBOR
- Joystick Audibax
Nyeste Joystick Manualer
11 December 2024
10 December 2024
10 December 2024
10 December 2024
10 December 2024
29 November 2024
26 November 2024
26 November 2024
26 November 2024
26 November 2024