Sony RM-V401 Manual

Sony Fjernbetjening RM-V401

Læs nedenfor 📖 manual på dansk for Sony RM-V401 (2 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Notes

• If you are using more than one receiver (or amplifier) and have set

it on the or button, when selecting theseCBL/SAT, CD, AUX DVD

buttons you cannot control the volume of the receiver (or

amplifier) of the button.RCVR

• If you change the setting of the button to a component otherRCVR

than a receiver or amplifier, the volume control setting of video

components will return to “TV” even if you have changed the

factory preset volume control. In this case, you will not be able to

control the volume from audio components other than a receiver

or amplifier.

To reset to factory preset volume control

In step 3 above, press instead.VOL–

Operating a Component

1Press the button of the desired

component on the Commander.

2Point the Commander directly at the

component.

3Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the

buttons on the Commander.

Notes on Using the Remote Commander

Basically, use this Commander in the same way as the Commanders

supplied with your components.

• Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to the

functions of the components themselves. For example, if your TV

does not have a MUTING function, the button on thisMUTING

Commander will not function with your TV.

• Some functions of the component may not work with this

Commander.

• If your cable box can control volume, be sure to set its volume

switch to a medium position. If the volume on the cable box is

turned down completely, you will not be able to adjust your TV’s

volume with the Commander.

Setting a channel with a single button

(Channel macro function)

You can program the Channel Macro function on any of the buttons

listed below (macro keys).

For example, instead of pressing , , and then button toENT

change the TV channel, you can perform these operations by

pressing only the N button.

The macro keys are:

N m M x X z, , , , , and REC.

(During TV, cable box, or digital satellite receiver operations only.)

The series of operations that can be programmed must be consisted

of two to four sequential pressings of to buttons or button.ENT

Note

The Channel Macro function may not work correctly for some

components.

To program a series of operations

1Press the desired component select button.

(You can select “TV”, “cable box”, or “digital satellite receiver”

only.)

2While pressing the desired macro key, press the buttons required

for the operations in sequence.

For example, to program t t on the button, holdENT N

down first, press , , and in sequence, and then releaseN ENT

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

Setting Up the Remote Commander

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand

components.

If you’re using the Commander with a Sony component, you won’t

need to preset the Commander before you start using it.

To set up the Commander to use with other (non-Sony)

manufacturers’ components, or to use with a component that is not

preset at the factory, you’ll need to follow the instructions in this

manual to preset the Commander with the correct code number for

your components. (See the supplied “Component Code Numbers”

also.)

Notes

• The Commander can be set up to operate only one component per

button – unless their code numbers happen to be the same. For

example, you cannot set up the Commander to operate a Sony TV

and a Panasonic TV simultaneously (because they use different

code numbers).

• You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in

“Setting the Code.”

Remote Button Descriptions

Installing the Batteries

Slide open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to line up the + and – on the batteries with the + and – on the

battery compartment.

1 2

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the

Commander does not operate properly, the batteries might be worn

out. Replace the batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than 20 minutes to replace the batteries;

otherwise, your setting of the code numbers will be erased.

Notes on Batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use

with the Commander.

Step 1: Entering the Code Number

1See the supplied “Component Code numbers”, and find the three-

digit code number for the desired component.

If more than one code number is listed, use the number that’s

listed first to complete the steps below.

For example, if you’re setting up a Philips’ VCR, you would use

the code number 035.

If your component isn’t listed, see “Searching for the Correct

Code.”

2Press the button with a ball-pointSET

pen tip etc., and release it.

3Press the button of the component that

you want to set up.

Note

On the , , , , and buttons, “cable box”,CBL/SAT RCVR CD AUX DVD

“receiver”, “CD player”, “tape deck”, and “DVD player” are

assigned respectively at the factory. But you can also assign other

components on these buttons. For details, see “Changing the

Component Type on the , , , , and CBL/SAT RCVR CD AUX DVD

buttons.”

4Enter the component’s code number.

For example, if you’re entering the code

for a Philips VCR, you would press

5Press and release the button to storeENT

the code number in the Commander’s

memory.

6Go to “Step 2: Checking if the Code Number Works” to finish

setting up.

Step 2: Checking if the Code Number Works

1Power on the component you want to set up.

2Aim the Remote Commander at the component and press a button

to check if that button works.

For example, press the button to see if it works on yourPOWER

component .

3Check that the other buttons of the Commander is operating the

corresponding functions of the component.

If the Commander Doesn’t Seem to Be Working...

• First, try repeating these setup procedures using the other codes

listed for your component (see the supplied “Component Code

Numbers”).

• If – after trying all the codes listed for your component – you still

cannot get the Commander to work properly, try the search

method described in “Searching for the Correct Code.”

Tip

You can write down the code number on the label inside the battery

compartment lid.

Searching for the Correct Code

If you’ve tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component is

not listed in the “Component Code Numbers” tables), try these

steps.

1Power on the component you want to set up. Insert a tape or disc

if necessary.

2Press the button with a ball-point pen tip etc., and release it.SET

3Press the button of the component on the Commander that you

want to set up.

4Press and release the button. Then press and release theCH+

POWER button.

5Repeat step 4 until the correct code number is found.

Each time you press the button and then the button,CH+ POWER

a new code number will be transmitted.

Keep trying until your component operates by receiving the

transmitted signal from the Commander (e.g., the power turns off,

the CH+ function works, playback starts, etc.) Be patient as you do

this; it may take about 100 tries until the correct code number is

located.

6When the correct code is found, press the button to store theENT

code number in the Commander’s memory.

7Check that the Commander is operating the other functions of

your component by pressing the corresponding buttons on the

Commander. If they seem to be working properly, you’re done

setting up the Commander.

If the component does not operate properly, repeat steps 1 to 6 and

search for another code.

If you still cannot get the Commander to work properly, see

“Troubleshooting.”

Changing the Component Type on the CBL/

SAT, RCVR, CD, AUX and DVD buttons

At the factory, “cable box” is assigned on the button,CBL/SAT

“receiver” on the button, “CD player” on the button, “tapeRCVR CD

deck” on the button and “DVD player” on the button. ByAUX DVD

completing the following procedure, you can change this setting so

that you can set up any component on these buttons.

1Press the button with a ball-point pen tip etc., and release it.SET

2Press the , , , , or CBL/SAT RCVR CD AUX DVD button.

3Press and release the x (stop) button.

4Press and release one of the following buttons;

to assign a VCR

to assign a digital satellite receiver

to assign a receiver

to assign a CD player

to assign a tape deck

to assign an MD deck or a DAT deck

to assign a TV

to assign a cable box

to assign a DVD player

5Press and release the ENT button.

6Enter the component’s code number by following steps 2 to 6 of

“Entering the Code Number”, or steps 1to 7 of “Searching for the

Correct Code.”

Controlling the Volume of Video

Components Connected to an Audio

System

The Commander is factory preset based on the assumption that you

hear the sound of your video components from your TV’s speakers,

and that you hear the sound of your audio components from the

loudspeakers connected to your receiver (or amplifier).

Factory Setting:

*If you assign an audio component on the or button,CBL/SAT, CD, AUX DVD

you can control the volume of the receiver (or amplifier) on the button.RCVR

If you assign video components on these buttons, you can control the volume

of the TV.

Thus you can control the volume of your TV or receiver (or

amplifier) while operating a video or audio component without first

having to press the or button. For example, to control theTV RCVR

volume for your VCR channels, you don’t need to press the TV

button first.

However, if your video components are connected to an audio

system, you probably hear your TV’s or VCR’s sound from the

loudspeakers connected to your receiver (or amplifier), not from

your TV speakers. In this case, you need to change the factory setting

so that you can control the volume of your video components

without first having to switch to the receiver (or amplifier).

To change the factory setting for the volume control, follow the

procedures below.

Note

This feature is effective only when a receiver or amplifier is set up on

the button. You cannot control the volume of a receiver (orRCVR

amplifier) set up on button whileCBL/SAT, CD, AUX DVD or

operating a component of another button.

Changing the Factory Setting for the

Volume Control

1Press the button with a ball-point pen tip, etc. and release it.SET

2Press the button.RCVR

3Press the button.VOL+

4Press the button.ENT

The volume control setting is changed to “receiver/amplifier.” You

can control the volume of the receiver (or amplifier) of the RCVR

button while selecting any component.

Button

VCR, CBL/SAT , DVD* *

RCVR

CD , AUX* *

Controls the volume of

Receiver (or amplifier)

Receiver (or amplifier) on the RCVR

button

Component that can be preset

VCR

Cable box/Digital satellite receiver/

Receiver/CD player/Tape deck/

MD deck/DAT deck/DVD player/

TV/VCR

Button

VCR

CBL/SAT

RCVR

AUX

DVD

Factory setting

Sony TV

Sony VHS VCR

—

Sony receiver

Sony CD player

Sony tape deck

Sony DVD player

English

3-220-548- (1)11

Remote Commander RM-V401

Operating Instructions

Manual de instrucciones (parte posterior)

Your Code Number

PIP operations

Press To

zREC Turn on/off the “window” picture.*

PIP and ENT Turn off the “window” picture.

m M or Change the TV channel in the “window” picture.

PIP and TV/VIDEO Change the input mode of the “window” picture.

xMove the location of the “window” picture.

NSwap the “main” picture and the “window” picture.

XFreeze the “window” picture.

Operating a DVD player

3To select numbers 10 and

above. For example, to select

track 15, press and thenPIP

press 5.

4N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

X: To pause.

5To display the title menu.

6To move the cursor upward,

downward, to the left, or to the

right.

7To display the DVD menu.

8To clear the selected characters

from the screen.

3 4 5, , and

TV: To operate the Picture-in-

Picture function. Press each

button or combination of

buttons as described in the

table below.

VCR:

N: To play.

x: To stop.

m: To rewind.

M: To fast-forward.

z NREC: To record, press

while pressing z.

6TV/VCR: To move the cursor

upward, downward, to the left,

or to the right.

7TV/VCR: To call up the MENU

display.

Specifications

Operable distance Approx. 7 m (23 ft) (varies depending of the

component of each manufacturer)

Power requirements Two size AA (R6) batteries (not supplied)

Battery life Approx. 6 months (varies depending on frequency of

use)

Dimensions Approx. 62 207 41 mm (w/h/d)× ×

(2 1/ 2× 8 1/ 4× 1 5/8 in.)

Mass Approx. 100 g (3.5 oz.) (not including batteries)

Design and specifications are subject to change without notice.

Operating a TV, VCR, or cable box

General

1To turn on and off the power of

the selected component.

2Component select buttons. To

switch to the operations of each

component, press the button on

which that component is

assigned.

9*Volume up: +

Volume down: –

q; *To mute the volume on TV or

receiver (amplifier).

qs To set up the Commander.

*These buttons control the volume of

either TV or receiver (amplifier). See

“Controlling the Volume of Video

Components Connected to an

Audio System” for details.

qa TV: To display the current

channel on TV.

VCR: To expose the on-screen

display.

qd and qf

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

qg TV/VCR: To enter the selection.

qh TV: To operate SLEEP function

on the TV. (Works only for a

TV with the SLEEP function.)

qj Channel up: +

Channel down: –

qk TV/cable box: To operate

JUMP FLASHBACK, or

CHANNEL RETURN function on

the TV depending on the

setting of the TV's

manufacturer.

VCR: To cancel.

Notes

• There may be cases you may turn on/off the cable box by pressing the orCH+

CH– buttons on the Commander.

• If your cable box can control volume, be sure to set its volume control to a

medium position. If the volume on the cable box is turned down completely,

you will not be able to adjust your TV’s volume with the Commander.

Notes

• Even if you try to program more than four operations and press the

corresponding buttons in step 2 above, only the first four buttons

that were pressed will be programmed.

• If you try to program only one operation on a macro key, the

setting operation will be rejected.

• You can program the Channel Macro function for up to three

components only. To program for the fourth component, first clear

all macro keys for a component.

To change or clear the program

When you want to change the setting or if you are no longer using

that programmed operation, follow the procedure below to

overwrite or clear the program.

1Hold down the macro key that you want to change or clear.

2After waiting for about three seconds, press the new sequence of

buttons, or, to clear the program, press and release , and then

press and release ENT.

3Release the macro key.

Note

Be sure to wait for about three seconds in step 2 above. While you

are holding down the macro key and waiting, the programmed

signals are transmitted; therefore, if you are aiming the Commander

at your component, the programmed operations may be performed

before you go on with the procedure.

Troubleshooting

If you have problems setting up or using the Commander:

• When setting up the Commander, carefully go through the procedures

described in “Setting the Code.” If the code that’s listed first for your

component doesn’t work, try all the codes for your component - in the order

in which they’re listed. If all the codes fail to work (or if your component is

not listed in this manual), try using the procedures in “Searching for the

Correct Code.”

• Check that you’re aiming the Commander directly at the component, and that

there are no obstructions between the Commander and the component.

• Make sure the batteries you’re using are not worn out, and that they’re

inserted correctly.

• Check that the button of the , , , , , TV VCR CBL/SAT RCVR CD AUX or isDVD

pressed to choose your desired component.

• Check that the component has infrared remote capability. For example, if

your component didn’t come with a remote commander, it probably isn’t

capable of being controlled by a remote commander.

• If your video components are connected to an audio system, make sure

you’ve set up the Commander as described in “Controlling the Volume of

Video Components Connected to an Audio System.”

• Should any problem persist, reset the Commander to the factory setting by

pressing the , and – buttons simultaneously.POWER TV/VIDEO VOL

For the customers in the U.S.A.

Customer Support Information

If – after you’ve read through this manual – you still cannot get the

Remote Commander to work properly, call the Sony Customer

Support Helpline at 1-800-822-2217.

qa To show the current play status

on the screen.

qd Number buttons : To set items

selected from the screen.

qf To enter the setting. To set

items selected from the screen.

qg To execute items selected from

the screen.

qh To switch the subtitle.

qj To proceed to next/previous

location or song.

qk To return to the last previous

screen.

ql To change the sound.

*If the “window” picture does not turn off this way, try pressing whileENT

pressing PIP.

Note

If you have programmed the Channel Macro function for TV operation, the

button used as a macro key cannot be used for PIP operation.

Operating a digital satellite receiver

Operating a tape deck

3 4 5, , and

Tape operation buttons.

For dual cassette decks,

operation buttons for Deck A

(for Sony-brand dual cassette

deck, buttons for Deck B).

PIP: To reverse.

N: To play.

m: To rewind.

M: To fast-forward.

z NREC: To record, press

while pressing REC.z

First release , thenN

release REC.z

x: To stop.

X: To pause

6 7 qf, , , and qg

Operation buttons for Deck B

(for Sony-brand dual cassette

deck, buttons for Deck A).

3To use the “FAVORITE”

function.

6To scroll through the Master

Guide.

7To call up the MENU display.

8To bring up the Master Guide.

qd and qf

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

qg To select the channel that's

highlighted. To bring up the

Station Index when a program

guide is not displayed.

qh To bring up the Station Index.

qj Channel up: +

Channel down: –

To page through the guide

when a program guide is

displayed.

qk To tune to the last tuned

station.

ql To switch the output of the

digital satellite receiver to the

TV. (When you connect a TV

cable or antenna to the receiver,

the output switches between a

TV and SAT program.)

Operating a receiver/amplifier

4Work as , , , , N M m x X

buttons of the CD player.

(When a CD player is set up on

the CD button.)

qd To select the input source:

1 selects VIDEO 1

2 selects VIDEO 2

3 selects AUX

4 selects TUNER

5 selects CD

6 selects TAPE

7 selects MD

8 selects TV

9 selects PHONO

0 selects DVD

qj Presetting frequency up: +,

down: –

Tuning frequency up: +,

down: –

qk To shift band (FM/AM).

ql To switch input source by each

pressing.

Operating a CD player, an MD deck, or a DAT deck

3To select numbers 10 and

above. For example, to select

track 15, press and thenPIP

press 5.

4N: To play.

m: To select previous track.

M: To select next track.

x: To stop.

X: To pause.

5MD deck/DAT deck: To record,

press /N while pressing z

First release , then release .N z

qd To select the track number. 0

selects track 10. To select track

numbers above 10, see the

descriptions on the buttonPIP

above.

qk CD player/MD deck: To select

next disc.

ENT: To reverse.

: To play.

: To rewind.

: To fast-forward.

: To stop.

MENU: To record, press

while pressing MENU.

First release , and

then release MENU.

OK: To pause.

qk To select Deck A or Deck B

(dual cassette deck only).

If your tape deck’s commander has

one set of tape operating buttons, and

has an A/B button for the deck

selection, use the button toRECALL

select Deck A or Deck B.

Produkt Specifikationer

Mærke:	Sony
Kategori:	Fjernbetjening
Model:	RM-V401

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony RM-V401 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Sony Manualer

16 September 2024

15 September 2024

14 September 2024

9 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

Sony RM-VS10TV Manual

2 September 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Nanlite BT-BCS-48V3.5mm Manual

21 December 2024

SMK-Link VP3700 Manual

17 December 2024

Metronic ZAP 2 Unic - 495399 Manual

17 December 2024

Metronic ZAP 3 - 495373 Manual

17 December 2024

Metronic ZAP 3 - 495309 Manual

17 December 2024

Metronic ZAP 3 - 495308 Manual

17 December 2024

Metronic 495390 Manual

17 December 2024

Metronic 495387 ZAP 3 Manual

17 December 2024

Metronic ZAP 6 Manual

17 December 2024

EQ-3 HM-RC-19-B Manual

16 December 2024