Star Micronics TSP100III Manual


Læs nedenfor 📖 manual på dansk for Star Micronics TSP100III (3 sider) i kategorien Printer. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
Set Up the Printer
For customers using Windows TabletPC < What to Do First >
For customers using iPad / iPhone / iPod touchAndroid <Optional>
What's Included
If contents are missing or damaged, please contact the reseller that sold you
the printer.
*accessories vary depending on the region where the printer was purchased.
iPad, iPhone, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning are trademarks of Apple Inc. IOS is a trademark or registered trademark of Cisco in the U.S.
and other countries and is used under license.
Android is a trademark of Google Inc.
Windows is a registered trademark of Microsoft Corporation.
For more information please visit our FAQ site at: http://www.starmicronics.com/support/faq.aspx
Download the TSP100 Windows Driver “futurePRNT
Extract the futurePRNT software and run Autorun.
exe”
Follow the wizard and install the software.
The connection will be completed by simply
connecting the USB cable.
A TSP100III utility is available from the following link which will
allow you to check printer operation or change settings.
iPad / iPhone / iPod touch
Windows
Android
Using the lighting cable provided with your apple product, connect it to the port on
the left (type A) and secure it with the cable lock. Connect the opposite end to
your Apple product .
Using the supplied USB cable, connect it to the port in the middle (type B) and
secure it with the cable lock . Connect the opposite end to the PC.
Using your USB to type B cable, connect it to the port in the middle (type B) and
secure it with the cable lock. Connect the opposite end to your Android device .
Easy Setup Guide
Copyright © 2017 Star Micronics Co., Ltd. 80877840
TSP100IIIU
Install it before connecting a USB cable.
3
Turn ON the Main Unit
Power
Connect the included power cable to the inlet
on the back side of the TSP100III. Connect the
plug of the power cable to the outlet.
Turn on the power to the TSP100III , and check
the blue LED lights up .
2 Inserting a Paper Roll
Push the cover opening lever and then
open the rear cover .
1 Connect a USB cable
When using a paper roll with 58 mm
width, install the supplied paper
guide into the printer.
To change the paper width, the
memory switch must be set. Refer to
the online manual for details.
Insert a paper roll in the direction shown
in the illustration.
Pull the end of the paper out straight ,
and push down both sides of the printer
cover to close .
Installing the Windows driver
This completes printer setup.
On Windows, the device driver software will
be installed automatically. Shortly thereafter,
your device will be ready to use.
There are various plugs
for Android devices
www.star-m.jp/
tsp100iiiu-oml.html
TSP100IIIU online manual
This document explains the setup procedure for the TSP100IIIU.
For further instructions, please refer to the TSP100IIIU online manual.
Please read the instructions before using the printer.
Introduction
The drivers can be downloaded using the link below:
www.star-m.jp/tsp100iii-wsw.html
Download the TSP100 futurePRNT Driver
The Windows drivers are included in futurePRNT.
When futurePRNT is used, the printer settings can be
configured and an operation test can be performed.
You will need:
USB cable included with the
printer
You will need:
Lightning cable included with
your apple product
You will need:
 USB cable (sold commercially or
one that comes with a tablet)
A specific USB On-the-Go adapter
may be required for your Android
product, please contact your
tablet manufacturer.
3
3
3
DK
5V
5V DK
1
2
DK
5V
5V DK
1
2
DK
5V
5V DK
1
2
www.star-m.jp/tsp100iii-app.html
Access if from your iOS or Android device.
TSP100III Utility Download
3
4
OFF ON
I
O
FEE D
ERROR
4
3
1
2
RST
2
1
TSP100III
Paper Roll Guide
Paper RollUSB Cable
Easy Setup Guide
This Sheet
Safety InstructionsPower Cable* Holder Plate
Rubber Feet Screws(2)Switch Cover
Plugfortheprinter
(TypeB)
Plugfortheprinter
(TypeA)
Plugfortheprinter
(TypeB)


Produkt Specifikationer

Mærke: Star Micronics
Kategori: Printer
Model: TSP100III

Har du brug for hjælp?

Hvis du har brug for hjælp til Star Micronics TSP100III stil et spørgsmål nedenfor, og andre brugere vil svare dig




Printer Star Micronics Manualer

Printer Manualer

Nyeste Printer Manualer