Techly I-CASE TRAY-ORG800 Manual

Techly Ikke kategoriseret I-CASE TRAY-ORG800

Læs nedenfor 📖 manual på dansk for Techly I-CASE TRAY-ORG800 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
WWW.TECHLY.COM
CABLE MANAGEMENT TRAY
USER'S
MANUAL
INTRODUCTION
This rack cable management system is a smart solution for tidying up cables and neatly managing
cabling inside a 19” rack.
Ideal for keeping the wiring tidy and clean, essential for checking and replacing the cables.
FUNCTION DESCRIPTION
Clear identification:
With layer identification, connection relationship identification, line direction identification
INSTALLATION AND OPERATION INSTRUCTIONS
Item Name Picture Qty Remark
Cable
Management
1
M6*16 Cabinet
Screws
2
Used for fixing the front
of the cable tray
M6*40 Cabinet
Screws
2
Used for fixing the side
of the cable tray
Spacers*
2
Used for fixing the side
of the cable tray for 800
and 1000mm versions
Cable
Channel*
6
For cables routing, only for
800 and 1000mm versions
Connecting
Rod*
2
Used for cabinets with a
depth of 800mm / 1000mm
Foam Stick
1
Auxiliary tools to ensure
that the bending radians
of the network cables are
consistent
Cable Tie
2
Used for cabinets with a
depth of more than 800mm
Low cost of repeated cable management:
When a line is messy, it does not affect the overall
line direction, convenient and quick recovery
Standardized and cost-effective construction
One-to-one channel routing, non-professional
can achieve standardized wiring
STRUTTURA DEL
Connection
Relationship
Identification
Line Direction
Identification
Layer
Identification
Insert the cable management system into the rack cabinet in the direction indicated by the arrow in
figure 1
Fix to the front rails of the rack in the desired position using M6x16 screws
Secure laterally to the rack using the M6x40 screws that will lock the cable management tray to the
rear rails** (figure 2)
Insert the cable in the desired position and slide it into the guide until it comes out on the other side
of the panel; it is possible to insert the cable both from the front and from the side holes
After cable installation, it is possible to block the cable by inserting the rubber cable clamp on the
front hole of the organizer
For more careful and precise cable management, you can use the supplied foam tube to create an
even bend for all cables. After extracting the cable from the hole, pass it on the surface of the foam
stick and connect it to the equipment to give the correct bending radius, once this step has been
carried out for all the cables, remove the foam stick
One or more organizers can be used within the same rack cabinet depending on the installation
requirements
** For models with depths of 800 and 1000mm it is necessary to install the connection bracket using
the 4 screws supplied; to fix the bracket to the rail, use the spacers and cable ties provided
PACKING LIST
PRODUCT STRUCTURE AND COMPONENT NAMES
Cable Management
Connecting Rod Support Column
Cable Channel
Cabinet Screws
Figure 1 Figure 2
Foam Stick Cable Channel
Support Column
Buckle Position
Cabinet
Screws
* Only for 800 and 1000mm deep version, not included for 600mm version


Produkt Specifikationer

Mærke: Techly
Kategori: Ikke kategoriseret
Model: I-CASE TRAY-ORG800

Har du brug for hjælp?

Hvis du har brug for hjælp til Techly I-CASE TRAY-ORG800 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Techly Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer