Toshiba TDP-P7 Manual

Toshiba videoprojektorer TDP-P7

Læs nedenfor 📖 manual på dansk for Toshiba TDP-P7 (64 sider) i kategorien videoprojektorer. Denne guide var nyttig for 24 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/64
T D P - P 7
FREEZE
MUTE
LASER
AUTO
TIM
ER
RG BVIDEO
R-CLICK/
CANCEL
QU
IC K
M
EN U
EN TER
STA
NDBY
Q
1 2
34
VOL Z OOM
IMPORTANT
* DLP™ (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instru-
ments Incorporated (U.S.A.).
* VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U.S.A.).
* S-VGA is a registered trademark of Video Electronics Standards Association.
* Microsoft, Windows, and PowerPoint are registered trademarks of Microsoft Corporation (U.S.A. and other countries).
* Macintosh is a trademark of Apple Computer Inc. (U.S.A.).
Note that even in the absence of explanatory notes, serious attention is paid to the trademarks of the various companies
and to the product trademarks.
DATA PROJECTOR
TDP-P7
OWNER’S MANUAL
DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
U.S. Responsible Party:
Address:
Tel. No.:
PLUS Vision Corp. of America
9610 SW Sunshine Court Suite 800 Beaverton,
OR 97005
(503) 748 8700
Type of Product:
Equipment Classification:
Models:
Projector
Class B Peripheral
V-332
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
RF Interference
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorientate or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regula-
tions.
E-1
E-2
IMPORTANT SAFETY INFORMATION
Precautions
Please read this manual carefully before using your PLUS Data Projector and keep the manual handy for future
reference.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude
to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside
of this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of
this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
The above cautions are given on the bottom of the product.
Hg: Lamp in This Product Contains Mercury. Dispose of Lamp According to Local, State or Federal Law.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE
THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE
PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM-
PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED PLUS SERVICE PERSONNEL.
CAUTION
Do not look at the laser pointer’s light source.
Be sure to heed the following. Pointing the laser beam at
the eyes could lead to reduced vision or vision impairment.
• Never look at the laser pointer’s light source.
• Do not point the laser beam at people.
• Do not let children use the laser pointer. This label is located on the side of the remote control.
E-3
Important Safeguards
These safety instructions are to ensure the long life of the unit and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
• For best results, use the unit in a darkened room.
• Place the unit on a flat, level surface in a dry area away from dust and moisture.
• Do not place the unit in direct sunlight, near heaters or heat radiating appliances.
• Exposure to direct sunlight, smoke or steam can harm internal components.
• Handle the unit carefully. Dropping or jarring can damage internal components.
• Do not place heavy objects on top of the unit.
Power Supply
• The unit is designed to operate on a power supply of 100 - 240 V 50/60 Hz AC. Ensure that your power supply
fits these requirements before attempting to use the unit.
• Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or
fire.
• Disconnect the power cable (main’s lead) from the power outlet after using the unit.
Before disconnecting the power cable, make sure that the STANDBY indicator lights in amber (not blinking or
in green).
Cleaning
• Disconnect the power cable (main’s lead) from the unit.
• Clean the cabinet of the unit periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use
strong detergents or solvents such as alcohol or thinner.
• Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
• Clean the ventilation slots and speaker grills on the unit periodically using a vacuum cleaner. If accumulated
dust blocks the ventilation slots, the unit will overheat, which may cause the unit to malfunction.
Use a soft brush attachment when using the vacuum cleaner. Do not use a hard attachment, such as a crevice
tool, to prevent the damage to the unit.
Lamp Replacement
• Be sure to replace the lamp when the Status indicator comes on. If you continue to use the lamp after 2000
hours of usage, the lamp will turn off.
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the buildup of heat inside
the unit. Allow at least 10 cm (4 inches) of space between the unit and walls.
• Prevent foreign objects such as paper clips and bits of paper from falling into the unit. Do not attempt to retrieve
any objects that fell into the unit. Do not insert any metal objects such as a wire or screwdriver into the unit. If
something should fall into the unit, immediately disconnect the power cable from the unit and have the object
removed by a qualified PLUS service person.
• Do not place any liquids on top of the unit.
Carrying around
When carrying the unit around, please use the storage case that comes with it and, to protect the lens from
scratches, always shut the Iris Lens Cover. Also, do not subject the unit to strong mechanical shock.
CAUTION – HOT!
The area around the exhaust vents is hot during and immediately after image projection.
To avoid burns, keep your hands away from this area.
Wait until the exhaust vents area cools off before touching it.
Do not look into the lens while the unit is on. Serious damage to your eyes could result.
IMPORTANT SAFETY INFORMATION
E-4
Major Features
䡵 The evolution in mobile projectors
Mobile projectors can be taken and used anywhere. The TDL-P7 takes the convenience of the mobile projector even further,
offering a high brightness of 1,100 lm and a high contrast ratio of 2000:1 despite its compact size and light weight. A rotating
type lens cover that protects the lens when the projector is being carried and stored. A wireless remote control unit with lens
pointer enables impressive presentations in many situations.
䡵 Sharp, clear picture
The DLP™ display system affords RGB color fidelity and inconspicuous gaps between the individual dots, thereby permitting
the display of small characters and diagrams with distinct clarity.
䡵 High contrast ration of 2000:1
Use of a new generation of DMD devices has given birth to an amazing 2000:1 high contrast ratio.
By widening the difference of brightness between black and white, you can see a degree of sharpness that is greater than just
the brightness based on specifications.
䡵 Powerful functions for presentations
A wide variety of easy-to-set functions have been built into the projector, from a digital keystone correction function (used
when making settings) that corrects picture distortion, to an auto adjustment function that automatically identifies the PC
signal.
There is also a built-in “Presentation Timer” function for further presentation convenience.
䡵 Great moving image playback capabilities using the same principles as DLP Cinema
technology
Plus DLP type projectors have the same makings as the DLP Cinema technology used in movie theaters. Because of their
extremely fast response, even images with much movement – sports, movies – play smoothly without blurring.
䡵 Security lock function
The lock can be set so that a password must be input when the projector is started up. Without the correct password, no
operations other than turning the power on and off can be performed. This function effectively protects the projector from
unauthorized use.
䡵 Eco-mode switch function for the lamp output
Using the lamp Eco-mode will extend the life of the lamp and lower the power consumption.
By switching the lamp mode to suit your operating environment, you will save on lamp cost as well as contribute to energy
conservation and ecology.
E-5
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................................... E-2
Major Features ....................................................................................................................... E-4
Table of Contents ................................................................................................................... E-5
Checking the Supplied Accessories .................................................................................... E-7
Names of the Main Unit Parts ............................................................................................... E-8
Names of the Remote Control Parts .................................................................................. E-10
Preparing the Remote Control ............................................................................................. E-11
Button Battery Replacement ...................................................................................... E-11
Remote Control Range .............................................................................................. E-11
The Procedure Up to Projecting to the Screen ................................................................. E-12
Placement Guide .................................................................................................................. E-13
Screen Size and Projection Distance ........................................................................ E-13
Connecting Personal Computers and Video Equipment ................................................. E-14
Connections with Personal Computer ....................................................................... E-14
Connect the projector’s RBG connector using the included RGB signal cable. . E-14
To Output the External Output Signal of a Notebook Computer ......................... E-15
Connections with Composite Signals ........................................................................ E-16
Video Equipment with VIDEO Connectors .......................................................... E-16
Video Equipment with S-VIDEO Connectors ...................................................... E-16
Connections with Component Signals ....................................................................... E-17
When the Video Equipment Has a YCbCr Connector or YPbPr Connector ....... E-17
Connections with the AUDIO Jack ............................................................................ E-18
Power Cable Connections and Switching the Power On/Off ........................................... E-19
Operating................................................................................................................... E-19
Finishing .................................................................................................................... E-21
Adjustment of the Projection Screen ................................................................................. E-22
Adjustment of the Projection Screen ......................................................................... E-22
Making Adjustments with the Adjusters ............................................................... E-23
General Operation ................................................................................................................ E-24
Input Selection .......................................................................................................... E-24
Automatic Adjustment ............................................................................................... E-24
Freezing a Moving Picture ......................................................................................... E-26
Cancelling Video and Audio Temporarily ................................................................... E-26
Adjustment of the Volume .......................................................................................... E-27
Enlargement of the Image and Video Movement ...................................................... E-28
Using the Presentation Timer .................................................................................... E-29
Protecting the Projector with the Security Lock ......................................................... E-30
Using the Quick Menu ............................................................................................... E-32
Menu Operation Method ...................................................................................................... E-33
Performing Menu Operations .................................................................................... E-35
List of Item Names Offering Input Selection and Adjustments/Settings .................... E-38
Image ..................................................................................................................................... E-40
Brightness / Contrast / Color / Tint / Sharpness ........................................................ E-40
Picture Adj. / Fine Picture / H Position / V Position ................................................... E-40
Reset ......................................................................................................................... E-41
Color ...................................................................................................................................... E-42
Quick Color Adj. ........................................................................................................ E-42
Gamma ..................................................................................................................... E-42
Color Temp. ............................................................................................................... E-43
White ......................................................................................................................... E-43
Color Space .............................................................................................................. E-43
White Balance ........................................................................................................... E-44
E-6
Table of Contents
View ....................................................................................................................................... E-45
Aspect ....................................................................................................................... E-45
Filter .......................................................................................................................... E-45
Vertical Flip / Horizontal Flip ...................................................................................... E-46
Keystone ................................................................................................................... E-46
Keystone Save .......................................................................................................... E-46
Setup ..................................................................................................................................... E-47
Auto Source .............................................................................................................. E-47
Auto Power Off .......................................................................................................... E-47
Menu Position ........................................................................................................... E-48
Lamp Mode ............................................................................................................... E-48
Input Format .............................................................................................................. E-49
Presentation Timer .................................................................................................... E-49
Option ................................................................................................................................... E-50
Language .................................................................................................................. E-50
On Screen ................................................................................................................. E-50
Background ............................................................................................................... E-50
Startup Screen .......................................................................................................... E-51
Security Lock ............................................................................................................. E-51
Info. ....................................................................................................................................... E-52
Status ........................................................................................................................ E-52
Factory Default .......................................................................................................... E-52
Lamp Timer Reset ..................................................................................................... E-52
Resolution / Frequency ............................................................................................. E-53
Lamp Timer ............................................................................................................... E-53
When an Indicator is Lit or Flashing .................................................................................. E-54
Troubleshooting ................................................................................................................... E-55
Cleaning ................................................................................................................................ E-56
Replacing the Lamp Cartridge ............................................................................................ E-57
Specifications ....................................................................................................................... E-60
Table of Supported Frequency ........................................................................................... E-61
Cabinet Dimensions ............................................................................................................ E-62
E-7
Checking the Supplied Accessories
Remove the main unit and the accessories from the box and check that the following items are included.
Carrying case (for projector and accessories) [1]
This is a case designed for storing the projector and its acces-
sories.
Use this carrying case when storing or moving the projector.
RGB signal cable
(Mini D-sub 15-pin, 2 m / 6.6 feet) [1]
This is used in making connections with a personal computer.
See Page about connections.E-14
No. 773711000
Power cable (1.8 m / 5.9 feet) [1]
This power cable supplies power to the unit. See Page E-19
about connections.
OWNER’S MANUAL (CD-ROM edition) [1]
OWNER’S MANUAL (Simplified Edition) [1]
Security Sheet [1]
Security Label [1]
“ WARN ING”
Handling the cables supplied with this product, will expose you to lead, a
chemical known to the State of California to cause birth defects or other
reproductive harm.
Wash hands after handling.
ST
A
NDBY
STA
TUS
M
ENUQ
UIC K
M
ENU
Small inside
pocket
Outside pocket
HOW TO PUT THE PROJECTOR INTO THE STORAGE CASE
Close the lens cover of the projector and then put the pro-
jector into the case.
Put the remote control unit and the included cables in the
outside pocket.
Wireless remote control unit with laser pointer [1] /
Size AAA batteries [2]
This controls the projector. (See Page .)E-11
FREEZE
MUTE
LASER
AUTO
TIMER
VOL ZOOM
RGB VIDEO
R-CL
IC K/
CAN
CEL
QUICK
MENU
ENTER
STANDBY
Q
1 2
34
USB cable (type A, 2 m / 6.6 feet) [1]
Used to perform mouse operations on a computer using the
projector’s remote control unit. Connections are described on
Page .E-35
No. 777707000
E-8
Names of the Main Unit Parts
STA
NDBY
S
TAT
US
MENUQU
ICK
MENU
S
O
U
R
C
E
A
U
T
O
E
C LOZ
Adjuster button [E-23]
(Also on opposite side)
Focus ring [E-23]
Exhaust vents
Front adjusters [E-23]
Lamp cover [E-58]
Ventilation slots
Remote control
sensor [E-11]
Lens
Ventilation slots
Rear adjusters [ ]E-23
Speaker
Lens cover
Zoom ring [E-22]
Built-in security slot
(See description below.)
Built-in Security Slot
This security slot supports the MicroSaver Security System manufactured by
Kensington Microware Inc.
E-9
Names of the Main Unit Parts
STAN DBY
STAT US
MENUQUICK
MENU
AUDIO
MOUSE S-VIDEO VIDEO
RGB
S
O
U
R
C
E
A
U
T
O
STANDBYSTATUS
MENU QUICK
MENU
S
O
U
R
C
E
A
U
T
O
AUDIOMOUSE S-VIDEO VIDEORGB
Ventilation slots
AC IN connector [E-19]
Remote control sensor [E-11]
RGB connector [E-14, 17]
S-VIDEO connector [E-16]
VIDEO connector [E-16]
AUDIO connector [E-18]
Ventilation slot
STATUS indicator [E-19, 54]
Buttons used in menu and
quick menu operations
[ ]E-32, 33
SOURCE button [E-24]
MENU button [E-33]
STANDBY indicator [E-19, 54]
AUTO button [E-24]
ENTER button [E-20]
STANDBY button [E-19]
SELECT ( ) buttons왖왔왗왘
QUICK MENU button [E-32]
MOUSE connector [E-16]
E-10
Names of the Remote Control Parts/Preparing the Remote Control
Refer to the description (and diagram) for the remote control unit included with your projector.
Names of Parts/Preparing the Remote Control Unit
FREEZE
MUTE
LASER
AUTO
TIMER
VOL ZOOM
RGB VIDEO
R-CLICK/
CANCEL
QUICKMENU
ENTER
STANDBY
Q
1 2
3 4
VOL button [E-31]
(Volume adjustment)
STANDBY button [E-23, 25]
This button is used to switch ON
the power aand set the unit to the
STANDBY mode.
AUTO button [E-28]
(Automatic adjustment of the RGB
moving image)
Buttons used for menu operations
[ ]E-40
The , , and
buttons are
the select (왖왔왗, , and 왘) buttons.
FREEZE button [E-30]
(Freezes moving pictures) MUTE button [E-30]
(Temporarily cancels the video and
audio)
TIMER button [E-33]
(Presentation timer time setting
display)
ZOOM button [E-32]
(Digital zoom adjustment)
Buttons used for input selection
[ ]E-28
RGB button and VIDEO button
(VIDEO / S-VIDEO)
LASER button [E-34]
(Turns the laser point on and off)
QUICK button [E-39]
(Displays a simplified menu)
Buttons used for the PC mouse
function [E-35]
(JOG button and R-CLICK button)
Number buttons [E-37]
(Used for the security lock.)
Names of the Remote Control Parts
Note:
If a button on the remote control unit is held in continuously for approximately 30 seconds, signal transfer will be suspended. To resume
transferring signals, press the button again.
Also, to use the jog button after signal transfer has been suspended, first press any other button, then press the jog button.
Infrared transmitter [E-13]
Laser transmitter [E-34 E-35] L-CLICK button [ ]
E-11
Preparing the Remote Control
STANDBYSTATUS
MENU QUICKMENU
30°
50°
50°
4m/13.1 feet
4m/13.1 feet
7m/23.0 feet
7m/23.0 feet
20°20°
30°
Remote Control Range
Point the infrared transmitter of the remote control toward the remote control sensor located at the front or rear of the main unit
and operate.
Reception of the remote control signal should generally be possible within the range illustrated below.
Side View
Top View
Remote control in-
frared transmitter
Remote control sensor
Remote control
sensor
Remote control in-
frared transmitter
Note
* Exposure of the main unit's remote control sensor or the remote control infrared transmitter to bright light or the obstruction of the signal
by an obstacle located in the pathway may prevent operation.
* The remote control will not function when the battery is exhausted.
CAUTION
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Inserting the Batteries
When using the remote control for the first time, install the batteries that were supplied.
2Insert the batteries to match
the "+" and "–" as indicated in-
side the compartment.
1Slide the battery compartment
cover (located on the bottom of
the remote control) and pull off.
* When replacing batteries, purchase two of the same type of AAA battery.
* DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
(B)
(C)
(A)
3(A) Leaving a little space in the front,
close the lid, (B) then with the back
pressed tightly, (C) press the lid towards
the front.
E-12
The Procedure Up to Projecting to the Screen
Perform setup adjustments in the following order.
1 Position the projector
Determine the locations to set up the screen and the projector.
See “Placement Guide” on Page E-13.
2 Connect the video equipment and personal computer
Connect your equipment to the projector.
When making connections with the personal computer’s RGB connector, see “Connections with
Personal Computer” on Page E-14.
When making connections with the video equipment’s video connector or an S-video connector,
see “Connections with Composite Signals” on Page E-16.
When making connections with the video equipment’s YCbCr connector or YPbPr connector,
see “Connections with Component Signals” on Page E-17.
When playing the audio through the built-in speaker of the projector, see “Connections with the
AUDIO Jack” on Page E-18.
About DLP projectors
Though careful attention is paid to providing optimum quality, please note that with DLP type projectors, in rare cases there may
be black spots or bright spots among the picture elements.
Note:
* Please purchase a screen.
* A component cable (order code 28-690), which is available separately, is required to connect a DVD player or other equipment with YCbCr
connectors.
* A component cable (order code 28-690), which is available separately, is required to connect high definition (HD) video equipment or other
equipment with YPbPr connectors.
3 Connect the power cable and open the lens cover.
See “Operating” on Page E-19.
See “Finishing” on Page E-21.
4 When selecting the language of menu displays, etc.
(Only when the power is first switched on following purchase)
See “When [Menu Language Select] is Displayed Upon Switching On the Power” on Page E-20.
5 Switching on the power of the personal computer and video equipment
6 Properly adjust the projection image to the screen
See “Adjustment of the Projection Screen” on Page E-22.
7 Selecting input equipment
See “Input Selection” on Page E-24.
8 Adjust the screen or video image
Adjust the image to the optimum condition as required.
See the Table of Contents for the adjustment items.
E-13
Placement Guide
• Use this information as a guide to find out about the screen size when the projector is placed at a certain location, or
to find out the approximate size of a screen that will be required.
• The projection distance over which focussing is adjustable is 1.20 m (3.9 feet) to 14.17 m (46.50 feet). The projector
should be placed within this range.
Screen Size and Projection Distance
Unit: m (feet)
26"
40"
60"
80"
100"
120"
150"
180"
200"
250"
1.20 (3.94)
1.54– 1.85
(5.05–6.07)
2.33– 2.80
(7.64–9.19)
3.12– 3.75 (10.24 –12.30)
3.91– 4.70 (12.83 –15.42)
4.70– 5.64 (15.42 –18.50)
5.89– 7.07 (19.32 –23.20)
7.07–8.49 (23.20–27.84)
7.86– 9.44 (25.79 –30.95)
9.84–11.81 (32.28– 38.73)
11.81–14.17 (38.76–46.50)
h2
h1
300"
STAN
DBY
STATU
S
MENU QUICKMENU
AUDIO
MO
USE
S-VIDEO VIDEO
R
GB
S
O
U
R
C
E
A
U
T
O
Height from center of
lens to bottom edge
of the projection
Height from center of
lens to top edge of
the projection
Lens surface of
the main unit
Screen Size Designation (Inches)
* There is a tolerance of ±5% due to design values.
* This table uses the lens apex and lens center as references and requires that the projector be in a
horizontal condition (with front and rear adjusters fully withdrawn).
26"
40"
60"
80"
100"
120"
150"
180"
200"
250"
300"
0.53 0.40⳯
0.81 0.61⳯
1.22 0.91⳯
1.63 1.22⳯
2.03 1.52⳯
2.44 1.83⳯
3.05 2.29⳯
3.66 2.74⳯
4.06 3.05⳯
5.08 3.81⳯
6.10 4.57⳯
— – 1.20
1.54 – 1.85
2.33 – 2.80
3.12 – 3.75
3.91 – 4.70
4.70 – 5.64
5.89 – 7.07
7.07 – 8.49
7.86 – 9.44
9.84 – 11.81
11.81 –14.17
0.47
0.71
1.07
1.43
1.78
2.14
2.68
3.21
3.57
4.46
5.35
0.07
0.10
0.16
0.21
0.26
0.31
0.39
0.47
0.52
0.65
0.78
Screen Size
Designation (Inches)
Screen Size Width x Height Projection Distance Height h1 Height h2
1.73 1.30⳯
2.67 2.00⳯
4.00 3.00⳯
5.33 4.00⳯
6.67 5.00⳯
8.00 6.00⳯
10.00 ⳯7.50
12.00 ⳯9.00
13.33 10.00⳯
16.67 12.50⳯
20.00 15.00⳯
(m) (feet)
— – 3.94
5.04 – 6.08
7.64 – 9.19
10.23 – 12.30
12.82 – 15.41
15.42 – 18.52
19.31 – 23.18
23.20 – 27.84
25.79 – 30.95
32.28 – 38.73
38.76 – 46.50
1.52
2.34
3.51
4.68
5.85
7.02
8.78
10.53
11.70
14.63
17.55
(m) (feet) (m) (feet) (m) (feet)
Wide – Tele Wide – Tele
Width
Height
Screen size (Diagonal)
0.22
0.34
0.51
0.68
0.85
1.02
1.28
1.53
1.70
2.13
2.55
E-14
Connecting Personal Computers and Video Equipment
Connecting this unit with a personal computer permits presentation data to be projected as a large screen display at
conferences, lectures, and on other occasions. Furthermore, connecting this unit to a DVD player or other video equip-
ment source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home
theater.
Connections with Personal Computer
Please check the following before making connections with the personal computer.
• A suitable resolution for this projector is 1024 x 768 dots (XGA). The maximum displayable resolution is 1280 x 1024 dots (S-
XGA).
Make changes to a displayable resolution at the personal computer side. Please check with “Table of Supported Frequency”
on Page E-61.
• The setting method for the personal computer will differ depending on the specific model. Please read the personal computer
instruction manual or the on-line help information, or contact the manufacturer of your personal computer.
Connect the projector’s RBG connector using the included RGB signal cable.
• When making connections with the RGB connector of the projector, please make the connection via the supplied RGB signal
cable.
• The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “RGB”
using the menu sequence of [Setup] [Input Format] [RGB].→ →
See “Input Format” on Page E-49.
MONITOR OUT
Personal
computer
RGB signal cable (Supplied item)
Note:
* Before making connections, check the power of the projector and the equipment to be connected is switched off.
* omputerWhen projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook c
startup procedure as well as the operation that follows startup. Please consult the instruction manual of your notebook computer or the on-
line help.
E-15
Connecting Personal Computers and Video Equipment
To Output the External Output Signal of a Notebook Computer
When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook
computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your
notebook computer or the on-line help while performing the following procedure.
1Check whether a signal is being sent from the notebook computer to the projector.
An indication appearing on the liquid crystal display of the notebook computer does not necessarily mean that an external
output signal is being output.
REFERENCE: When “Resolution” or “Frequency” is not displayed under “Info.” on the menu of the projector, this means that
the external output signal is not being output from the personal computer. See “Resolution/Frequency” on Page E-53.
2Should a sign not be output from the notebook computer, please try the operation described below.
For an IBM PC/AT compatible computer, press the [Fn] key plus any one of the [F1] to [F10] keys. (See the table below.)
Note:
When the liquid crystal display of the notebook computer and the projector are displayed at the same time, the projected image might not be
correct even though the liquid crystal display shows a correct indication. Should this occur, stop the simultaneous display of the notebook
computer and try the mode with external output only. Try an operation such as that described in aforementioned Step 2 and try closing the
liquid crystal panel which might result in external output only.
Manufacturer Model Key
DELL All computers Fn + F8
EPSON All computers Fn + F8
FUJITSU All computers Fn + F10
iiyama All computers Fn + F3
IBM All computers Fn + F7
NEC All computers Fn + F3
Panasonic All computers Fn + F3
SHARP All computers Fn + F5
SONY All computers Fn + F7
SOTEC All computers Fn + F3–F5
TOSHIBA All computers Fn + F5
Victor All computers Fn + F10
Note: Table information is current to December 2003.
E-16
VIDEO S-VIDEO
Connecting Personal Computers and Video Equipment
Connections with Composite Signals
Video Equipment with VIDEO Connectors
• Connect to the projector’s VIDEO connector using a commercially available video cable.
• The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project,
please change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input
Format] [Video].→
See “Input Format” on Page E-49.
Video Equipment with S-VIDEO Connectors
• Connect to the projector’s S-VIDEO connector using a commercially available S-Video cable.
• The input setting of the S-VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project,
please change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input
format] [→S-Video].
See “Input Format” on Page E-49.
Video deck, DVD player, document
camera, etc.
Video cable (RCA pin plug)
(Commercially available)
S-Video cable (Mini DIN 4-pin plug)
(Commercially available)
E-17
CrCbY
PrPbY
COMPONENT
COMPONENT
Connecting Personal Computers and Video Equipment
Connections with Component Signals
When the Video Equipment Has a YCbCr Connector or YPbPr Connector
• The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Compo-
nent” using the menu sequence of [Setup] [Input Format] → → [RGB].
See “Input Format” on Page E-49.
• When projecting the YCbCr signal or YPbPr signal, if the color of the overall image strongly leans toward being greenish or
another color, change the setting under the menu of [Color] → [Color Space].
See “Color Space” on Page E-43.
Component cable (Available as an option)
(Mini D-sub 15-pin to RCA⳯3)
(Order code: 28-690)
Component cable (Available as an option)
(Mini D-sub 15-pin to RCA⳯3)
(Order code: 28-690)
Green
Blue
Red
Green
Blue
Red
E-18
Connecting Personal Computers and Video Equipment
Connections with the AUDIO Jack
* Connect to the projector’s AUDIO jack using a commercially available audio cable. If the other device has an RCA phono type
audio jack, connect via a commercially available audio converter cable.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio output of the video equipment to your audio system.
* The built-in speaker outputs the audio of the equipment connected to the AUDIO jack.
R
L
AUDIO OUT
White
Red
Audio conversion cable
(Mini-jack/ RCA pin plug)
(Commercially available)
Audio cable (Mini plug)
(Commercially available)
Audio cable (Mini plug)
(Commercially available)
E-19
S
O
U
R
C
E
A
U
T
O
ST
ANDBY
ST
ATU
S
M
ENU QUIC
K
M
ENU
AUDIO
M
OUS
ERGBS-V
ID EOVIDEO
Firmly plug in all the
way.
To wall outlet
Power Cable Connections and Switching the Power On/Off
There is an order in which the power cable is connected and the power is switched on/off.
Operating
3Switch on the projector power
Press the STANDBY button.
The first time the power is switched on after purchase, [Menu
Language Select] will be displayed. See Page E-20 for infor-
mation about language selection.
• When the power is turned on, the STANDBY indicator starts
flashing green, then stops flashing after about 60 seconds. If
the STATUS indicator lights green at this time, the lamp mode
is set to “Eco”. See and 48 for instructions on selecting.E-26
• If the power does not come on, see “When the STATUS Indica-
tor is Lit or Flashing” on Page E-54.
If the “Password” input window is displayed: See E-31.
A password is set for this projector.
The projector cannot be used unless the correct password is in-
put.
To turn off the power: See E-21.
The projector is now capable of regular projection.
4Switch on the power of the connected equipment
Note:
• When the power plug will be unplugged from the power outlet, please place the projector near the power outlet so that it may be reached
easily.
• Press the STANDBY button after the STANDBY indicator is lit in amber.
2 햲 Turn the lens cover clockwise.
햳 When the lens cover stops with a click, the projector is ready for projection.
1Connect the AC IN connector of the projector and the power outlet using the supplied power cable.
The STANDBY indicator will light in amber, and the unit will enter the standby mode.
STA
N
ST A
TUS
E
1
ST ANDB
Y
STATUS
M
E
C
E
2
STANDBYSTATUS
Lit amber
STANDBYSTATUS
(button on main unit)
STANDBYSTATUS STANDBYSTATUS STANDBYSTATUS
This indicator is also lit green in Eco-mode.
Flashing green
(Approximately 60
seconds)
Lit green
Power is on
Lit amber
LASER
AUTORGB VIDEO
QUICKMENU
Q
STANDBY
E-20
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-22.
1Press the SELECT 왖왔 buttons of the Remote con-
trol and align the deep blue cursor with [English].
Cursor
2Press the ENTER button to set.
This will set the language and [Menu Language Select] will close.
This completes the selection of the display language.
Caution:
[Menu Language Select] will not appear the next time the power is switched on.
Should a change of language become necessary, see “Language” on Page E-50.
Power Cable Connections and Switching the Power On/Off
FREEZE
MUTE
LASER
AUTO
TIMER
VOL ZOOM
RGB VIDEO
R-CLICK/
CANCEL
QUICKMENU
ENTER
STANDBY
Q
1 2
3 4
FREEZE
MUTE TIMER
VOL ZOOM
R-CLICK/
CANCEL
ENTER
1 2
3 4
E-21
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equip-
ment
2Switch off the power of the projector
Press the STANDBY button.
The [Power Off] display appears.
When the level gauge reaches maximum, the projection screen
will go off (in about 5 seconds) and the projector will enter the
power-off operation.
Note:
* The operation can be cancelled by pressing a button other than the
STANDBY button.
* One more press of the STANDBY button will switch off the power.
The STANDBY indicator changes to flashing amber and lights a
steady amber after about 90 seconds (when the unit enters the
standby mode).
Warrning
Do not unplug the power cable while the STANDBY indicator is flashing amber. Doing so may shorten the life of the lamp
or damage the projector.
Power Off
OK
?
STANDBYSTATUS
(button on main unit)
Flashing amber
(Approximately 90
seconds)
Lit amber
Standby mode
STANDBYSTATUS STANDBYSTATUS STANDBYSTATUS
Lit green
3Unplug the power cable
Check that the STANDBY indicator is lit in amber and then
unplug the power cable.
The STANDBY indicator will go off when the power cable is un-
plugged.
4 햲 Turn the lens cover counterclockwise until it stops.
햳 The lens cover will stop with a click.
ST ANDB
Y
ST A
TUS
MENU
E
E
CL OZ
1
ST ANDBY
ST AT US
MENU
E
2
LASER
AUTORGB VIDEO
QUICKMENU
Q
STANDBY
E-22
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
2
(2)
(1)
(3) (4)
(5)
(3)
(4)
Adjust the projection image to the screen.
Check that the screen is set level and vertically.
(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the screen and the center of
the projector lens.)
(2) If the image is shifted vertically, move the image up or down with the adjuster. See “Making Adjustments with the Adjust-
ers” on Page E-23.
(3) If the image is slanted, adjust by turning the right or left adjuster. See “Making Adjustments with the Adjusters” on Page
E-23.
(4) A projection image such as that illustrated in the diagram is the result of the projector not being perpendicular to the
screen. Set the projector so that it is pointing straight toward the screen.
(5) If the image shows keystone distortion, adjust using remote control or menu operations. See “Keystone” on Page E-46.
Turn the zoom ring to adjust the screen size of the projection image.
Adjust the image to match the desired screen size. When outside of the adjustment range, move the projector to the rear or
forward.
STANDBY
STATUS
MENU
E
CLO Z
1
Zoom ring
E-23
Adjustment of the Projection Screen
STAN
DBY
STATUS
ME NU QUICK
MENU
S
O
U
R
C
E
A
U
T
O
E
CL OZ
(1)
(2)
(1)
Note:
When the projector has a rear installation is used, the orientation of the projection will need to be changed.
Please see “Vertical Flip” on Page E-46.
Adjuster button
Making Adjustments with the Adjusters
Raising the projection image
While viewing the projection image, (1) press and hold
the front adjuster buttons located at the left and right and,
(2) raise the projector to align the image with the screen,
then release your fingers.
Turn the left and right front adjusters for fine adjustment.
Adjust so that there is no shaking of the projector.
Lowering the projection image
Lower the front adjusters using the operation described
above.
To lower the projection screen further, raise the rear ad-
juster. Fine adjustments are made by turning the left and
right front adjusters. Make adjustments so that there is
no rattling.
STANDBY
STATUS
MENU QUICK
MENU
AUDIO
MOUSE RGB S-VIDEO VIDEO
S
O
U
R
C
E
A
U
T
O
3Turn the focus ring and adjust the focus of the screen
STANDBY
STATUS
MENU
E
CL
O Z
Focus ring
E-24
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-33 and the various items on
Pages to E-40 E-53.
Input Selection
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while the menu or the quick menu is displayed.)
When Auto Source is On
Whenever the SOURCE button is pressed, the projector automatically selects
another source that has the next input signal.
When Auto Source is Off
The input selection condition used last time will be set.
Each press of the button moves the selection one step in the sequence of RGB →
VIDEO →S-VIDEO. Note that the various input signals will become the signal
type set with [Input Format] See “Input Format” on page E-49.
Remote control operation: Press the desired input selection button.
RGB button ........ Switches the RGB input.
VIDEO button ..... The input switches between VIDEO and S-VIDEO each time the button is
pressed.
When Auto Source is On
When an input signal is not present at the selected source, the projector automati-
cally selects the next source that has an input signal.
When Auto Source is Off
The projector switches to the selected source regardless of whether an input sig-
nal is present.
Note:
* When you do not operate source selection, the projector will assume the input selec-
tion condition that was previously used.
* See “Auto Source” on Page E-47 for information about the Auto Source on and off
conditions.
S
O
U
R
C
E
A
U
T
O
Automatic Adjustment
This function automatically adjusts the position shift, screen size, vertical stripes,
and color infidelity of the projected analog RGB input signal.
Normally automatic adjustment is performed at the time of signal selection.
Main unit operation/Remote control operation: Press the AUTO button.
(This will not function while the menu or the quick menu is displayed.)
A press of the AUTO button starts the automatic adjustment.
Note:
* If the display position is shifted, vertical lines appear on the picture, or the projection
is not good even after using automatic adjustment, please perform image adjustment
manually. See “Picture Adj. / Fine Picture / H Position / V Position” on Page E-40.
* When the image extends beyond the boundaries of the screen or is smaller than the
screen, set Aspect to “Auto”. See “Selection of Aspect Ratio” on Page E-25 and “As-
pect” on Page E-45.
S
O
U
R
C
E
A
U
T
O
FREEZE
MUTE
LASER
AUTO
TIMER
VOL ZOOM
R-CLICK/
CANCEL
QUICKMENU
ENTER
STANDBY
Q
1 2
3 4
RGB VIDEO
FREEZE
MUTE
LASER
TIMER
RGB VIDEO
R-CLICK/
CANCEL
QUICKMENU
ENTER
STANDBY
Q
AUTO
E-26
General Operation
Enlargement of the Image and Video Movement
This function digitally enlarges the personal computer image and video
image.
(1) Press the ZOOM button to enlarge the image.
The zoom display appears when the ZOOM button is pressed.
Each press of the 왖 button enlarges the image and each press of the
왔 button makes the image smaller (returning it to 1:1).
(No enlargement) (Approximately 2 times enlargement)
The image can also be moved in the following circumstances.
• When “Aspect” is set to “Real” by the signal of the personal computer, and the input resolution is
higher than the display resolution of the projector.
• When “Aspect” is set to “Zoom” by the video signal.
Note:
* Zoom and image movement functions are cancelled when the input is switched.
* The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected
so that they are not conspicuous.
* Movement of the screen will not be possible when the menu screen is being displayed.
Zoom
0
Zoom
21
(3) Press the CANCEL button to immediately close the display.
The display will close when there has not been an operation in about
10 seconds.
(2) Pressing the SELECT 왖왔왗왘 buttons on the remote control at
the time of the zoom operation will cause the display position to
move.
(There will not be any movement when zoom is at 0.)
(Approximately 2 times enlargement) (Movement)
Zoom
21
Zoom
21
Note:
After magnifying the image, be sure to use the ZOOM button to bring the gauge
value back to “0”.
(3)
(1)
(2)
FREEZE
MUTE
LASER
AUTO
TIMER
VOL
RGB VIDEO
R-CLICK/
CANCEL
QUICKMENU
ENTER
STANDBY
Q
1
3
ZOOM
2
4
E-27
General Operation
Using the Presentation Timer
Note:
* The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will
still be operating at such times. Also, the timer will not be displayed unless a signal is being input.
* While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.
[Timer settings display]
The presentation is given while checking the timer displayed
on the screen.
The gauge display allows the remaining time to be known at
a glance.
(1) Press the TIMER button to show the settings display.
The display will close when an operation has not been made
for about 10 seconds.
Press the CANCEL button to close the display immediately.
(2) Use the 왗 왘 and SELECT buttons to set the time.
The setting contents are “Off” and from 10 to 60 minutes (in
10-minute intervals)
Settings can also be made with the SELECT 왗왘 buttons.
Gauge (Blue)
• Press the ENTER button to restart the timer. The timer will
start with the same time setting.
• Press the CANCEL button to close the timer display. The
timer setting will return to “Off”.
Moving the Position of the Timer Display
The SELECT 왖왔왗왘 buttons on the remote control permit move-
ment within the movable range of the timer display.
(3) Press the ENTER button and start the timer.
• The display of the timer setting will close, the display of the
timer will appear and simultaneously the timer will start.
The blue gauge indicates the remaining time. When the
gauge disappears,the time is up.
The gauge continues to be displayed when the timer is
stopped.
[Timer Display]
When the remaining time is
“0” (Gray)
Movable Range of the Timer Display
FREEZE
MUTE
LASER
AUTO
VOL ZOOM
RGB VIDEO
R-CLICK/
CANCEL
QUICKMENU
STANDBY
Q
1 2
3 4
TIMER
ENTER
(1)
(2)
(3)
CANCEL button
E-28
General Operation
Using the Laser Pointer
The remote control unit’s laser pointer can be used to point to the section currently being explained, making presenta-
tions more effective.
Operation
The red laser beam is emitted from the tip of the remote control
unit while the LASER button is pressed in. Point the remote con-
trol unit’s transmitter in the direction you want to indicate.
The laser beam turns off when you release your finger from the
LASER button.
FRE
EZE
M
UT
E
LA S
ER
A
UTO
T
IM E
R
V
OLZ
OOM
RG BV
ID E
O
R-CLICK/
CANCEL
QU
ICK
M
EN
U
EN
TE
R
S
TA N
DB Y
Q
1 2
3 4
LASER
CAUTION
Do not look at the laser pointer’s light source.
Be sure to heed the following. Pointing the laser beam at
the eyes could lead to reduced vision or vision impairment.
• Never look at the laser pointer’s light source.
• Do not point the laser beam at people.
• Do not let children use the laser pointer. This label is located on the side of the remote control.
Note:
If a button on the remote control unit is held in continuously for approximately 30 seconds, signal transfer will be suspended. To resume
transferring signals, press the button again.
Also, to use the jog button after signal transfer has been suspended, first press any other button, then press the jog button.
E-29
General Operation
Performing Mouse Operations on the Computer
with the Remote Control Unit
When a computer and the projector are connected, mouse operations can be performed on the computer using the
projector’s remote control unit. When projecting images from the computer, the projector can be operated and mouse
operations on the computer performed with the same remote control unit, making for efficient presentations.
Connecting the computer and projector
Use the USB cable included with the projector to connect the computer’s USB (type A) connector to the projector’s MOUSE
connector.
Note:
* Be sure to plug the cable in securely.
* Depending on the type of connection, the computer’s operating system, etc., it may be necessary to change settings or restart the com-
puter after making the connections.
USB cable (mini B to A type) (Supplied item)
Functions of the mouse function buttons
When operating, point the remote control unit’s transmitter towards the remote control sensor on the projector.
Note:
Connections with USB Cables
* For PC/AT compatible computers, this function cannot be used with operating systems other than Windows 98SE, Me, 2000 and XP. For
Macintosh computers, this function cannot be used with operating systems other than OS 9 and later.
* jector,When the cable is disconnected and then reconnected to the USB port of the personal computer or the MOUSE connector of the pro
allow at least 5 seconds before reconnecting. Do not repeatedly disconnect and reconnect the cable in a momentary fashion. The personal
computer may not be able to correctly identify the projector as a result.
* The supplied USB cable is a dedicated cable for this projector. There is no guaranty that it will work in connections with other USB
equipment.
* This function may not work with some computers.
FREEZE
MUTE
LASER
AUTO
TIMER
VOL ZOOM
RGB VIDEO
QUICKMENU
ENTER
STANDBY
Q
1 2
3 4
R-CLICK/
CANCEL
L-CLICK button (on back)
Press this to perform the left-click operation.
JOG buttons
These move the computer’s pointer in the corresponding direction.
R-CLICK button
Press this to perform the right-click operation.
INFORMATION
The R-CLICK/CANCEL button is used for both the projector and mouse func-
tion. When the R-CLICK/CANCEL button is pressed while a menu is open, the
menu is closed.
USB connector
E-31
General Operation
If the password input display appears when the power is turned on
When a password has been registered, the “Password” input window appears on the projected image when the power is turned
on. The projector continues projecting this image until the correct password is input. At this time, only the STANDBY button
(power off) works. Use the procedure described below to input the registered password. For instructions on registering the
password, see E-30.
Input the password using the number buttons (1 to 4).
Be sure to input the registered 4-digit number.
Example: To input the password “2441”
Press number button “2”. An “*” (asterisk) appears at the first place.
Next press number buttons “4”, “4” and “1” in that order. Asterisks appear in all
four places.
If the password matches, the window turns off and the projector can be used
normally.
Canceling the password/Changing the password
The password is canceled and changed using the menus. For instructions on operating the menus, see “Menu Operation Method”
on E-33.
Canceling the password
Select “Security Lock” in the “Option” menu and set it to “Disable”.
This clears the password and disables the security lock.
The password input display no longer appears when the power is turned on.
Changing the password
After setting “Security Lock” to “Disable” as described above, set it back to “En-
able”. The menu closes and the password registration display appears.
Register the new password. See “Registering the password” on E-30.
[Password input window]
E-32
General Operation
Using the Quick Menu
This function permits frequently used adjustments to be performed
quickly.
Note that the Quick Menu will not be displayed unless the signal of the con-
nected equipment is input. Please select the input that you wish to adjust.
Main unit operation
(1) Press the QUICK MENU button to display the quick adjustment dis-
play.
Further presses cause the adjustment display to change in sequence.
Press the SELECT button to switch to the desired adjustment dis-왖 왔 or
play.
(2) Press the SELECT 왗 or 왘 button to adjust.
Remote control operation
(1) A press of the QUICK MENU button brings up the quick adjustment
display.
Further presses cause the adjustment display to change in sequence.
The adjustment display can be selected with use of either the SELECT 왖 or
왔 button.
(2) Press the cursor or 왗 왘 button to make the adjustment.
(3) To close the display immediately, press the CANCEL button.
In the absence of operations for a period of about 10 seconds, the display
will close automatically.
Brightness Adjusts the brightness of the image. See page E-40.
Contrast Adjusts the contrast of the image. See page E-40.
Keystone Corrects (vertical) keystone distortion of the screen. See page E-27.
Volume This function adjusts the volume of the built-in speaker. See page E-27.
Presentation timer Sets the time of the presentation timer. See page E-29.
Quick Color Adj. Select the preset color mode. See page E-42.
Content of Adjustments and Settings
Example: Brightness adjustment display
Display Item Adjustment/Setting
STANDBY
QUICK
MENU
S
O
U
R
C
E
A
U
T
O
(2)(1)
FREEZE
MUTE
LASER
AUTO
TIMER
VOL ZOOM
RGB VIDEO
R-CLICK/
CANCEL
MENU
ENTER
STANDBY
1 2
3 4
R-CLICK/
CANCEL
QUICK
Q
(1)
(2)
(3)
E-33
Menu Operation Method
• This section describes only the menu operation method. Please see this item should you need information while
performing menu operations.
• For information about a menu function, adjustment, or setting, please see one of the pages containing such descrip-
tions.
• Adjustments and settings are made by projecting an image and adjusting to an optimum condition.
• The remote control should be pointed toward the remote control sensor of the projector and operated.
• To return the various items that have been changed via the menu to their standard values (i.e., default values at time
of shipping from the factory), see “Factory Default” on Page (Some items will not return to their initial values.)E-52.
• The adjustment/setting items and contents will differ depending on the input selection and the adjustment/setting
items that can be used with the input signal are displayed on the menu.
Names and Functions of Buttons Used for Menu Operations
(Remote Control)
SELECT 왖왔왗왘 buttons
STANDBYSTATUS
MENU QUICK
MENU
S
O
U
R
C
E
A
U
T
O
(Main Unit)
ENTER button
MENU button
Used to display menus, to return to menu name selections,
and to close menus (i.e., closing sub menu displays).
FREEZE
MUTE
LASER
AUTO
TIMER
VOL ZOOM
RGB VIDEO
QUICK
STANDBY
Q
1 2
3 4
R-CLICK/
CANCEL
MENU
ENTER
MENU button
Used for menu display and menu closure.
SELECT buttons왖왔왗왘
Used in the selection of menu names and item names as
well as in setting and adjusting the item contents.
CANCEL button
Used to return to menu name selection as well as to close
the menu (and the sub menu display).
ENTER button
Used to set the verification display.
E-34
Menu Operation Method
Menu Screen Names and Functions
Menu Name
This is the title of the menu.
There is a change to the title screen
when the menu is selected.
The cursor moves to the selected menu
name.
Cursor (Deep Blue)
This permits setting/adjustment of the
item located at the cursor position.
Item Name
This is the name of the ad-
justment or setting.
Icon: Pressing the ENTER but-
ton displays the sub menu or set-
ting contents.
Settings ContentsItem Name
Sub menu
Adjustment Bar
Adjustment Bar and Settings Contents
Adjustment Bar: The increases and decreases in bar length ex-
press the adjustment condition.
Setting Contents: Displays the contents that have been set.
E-35
Menu Operation Method
Performing Menu Operations
• Only “Setup”, “Options” and “Info.” can be selected when no signal is being input.
• The menu display will close if, after pressing a button, the next button operation is not made within 30 seconds.
• The adjustment and the setting values are stored even when the power is switched off or the plug is disconnected
from the power outlet.
(Note that some items are not stored.)
Preparation Switch on the power of the connected equipment, start the play operation or another operation, and
input the signal to the projector.
Select the input that you wish to adjust.
The menu display of the description diagram depicts an example in which the “Keystone” item name is selected.
1Press the MENU button to display the menu
Menu Display
The menu name that existed when the menu was closed previously will be displayed.
Note:
Please check that the cursor of the item name has disappeared at the time of menu name selection.
Press the CANCEL button to make the cursor disappear.
2Press the SELECT button to select the menu name왗왘
Selection of the Menu Name
Each press of the SELECT utton advances the selection one step in the sequence of “Color” 왘 b → “View” “Setup” → →
“Option” →
“Info.”
→ “Image”. Each press of the SELECT 왗 button causes a return of one step.
The cursor moves to the selected menu name.
FREEZE
MUTE
LASER
AUTO
TIMER
RGB VIDEO
R-CLICK/
CANCEL
QUICK
ENTER
STANDBY
Q
MENU
FREEZE
MUTE
LASER
AUTO
TIMER
RGB VIDEO
R-CLICK/
CANCEL
QUICKMENU
ENTER
STANDBY
Q
E-37
Menu Operation Method
6Press the MENU button and close the menu display
Closing the Menu
Selecting Another Menu Name with Remote Control Operation
When a sub menu is displayed, press the CANCEL but-
ton and close the sub menu.
Press the CANCEL button again to turn off the item name
cursor.
Press the SELECT 왗왘 button and select the menu name.
(Menu names cannot be selected when the item name
cursor is displayed.)
Note:
A press of the QUICK button while the menu is displayed will close the menu and display the quick menu. A press of the MENU button while
the quick menu is displayed will close the quick menu and display the menu.
FREEZE
MUTE
LASER
AUTO
TIMER
RGB VIDEO
R-CLICK/
CANCEL
QUICK
ENTER
STANDBY
Q
MENU
FREEZE
MUTE
LASER
AUTO
TIMER
RGB VIDEO
QUICKMENU
ENTER
STANDBY
Q
R-CLICK/
CANCEL
FREEZE
MUTE
LASER
AUTO
TIMER
RGB VIDEO
R-CLICK/
CANCEL
QUICKMENU
ENTER
STANDBY
Q
E-38
List of Item Names Offering Input Selection and Adjustments/Settings
The item names that can be adjusted/set will differ depending on the input signal.
“Tint” can be adjusted only at the time of NTSC composite/S signal input.
Menu Operation Method
[Example of Menu Display Items at the Time of Input Signal RGB Selection]
RGB
Component
VIDEO
S-VIDEO
Menu name
Image
Color
View
Brightness E-40
嘷嘷嘷嘷
Item Name Sub Menu
Item Name
Contrast E-40
嘷
嘷
嘷嘷嘷
Picture Adj.
Fine Picture
E-40
H Position
E-41
V Position
E-41
嘷
嘷
嘷
嘷E-41
Reset E-41
嘷嘷嘷嘷
Gamma E-42
嘷嘷嘷嘷
Quick Color Adj. E-42
嘷
Color Temp. E-43
嘷嘷嘷嘷
White E-43
嘷嘷嘷嘷
Color Space
E-43
嘷
White Balance E-44
嘷
Aspect E-45
嘷嘷嘷嘷
Filter E-45
嘷嘷嘷嘷
Vertical Flip E-46
嘷嘷嘷嘷
Horizontal Flip E-46
嘷嘷嘷嘷
Keystone E-46
嘷嘷嘷嘷
Keystone Save E-46
嘷嘷嘷嘷
Reference
Page
Input Signal
Color
Tint
E-40
嘷 嘷
Sharpness
E-40
嘷 嘷
E-40
嘷 嘷
E-39
RGB
Component
VIDEO
S-VIDEO
Menu name
Setup
Info.
Auto Source
E-47
嘷嘷嘷嘷
Item Name
Reference
Page
Sub Menu
Item Name
Auto Power Off
E-47
嘷嘷嘷嘷
嘷 嘷 嘷
嘷 嘷 嘷
Menu Position
Lamp Mode
E-48
Input Format
E-48
RGB
嘷
嘷
嘷 嘷 嘷嘷
嘷 嘷 嘷嘷
嘷 嘷 嘷嘷
嘷 嘷
Video
E-49
S-Video
E-49
Presentation Timer
E-49
E-49
嘷 嘷
Language
On Screen
Background
Startup Screen
Option E-50
嘷嘷嘷嘷
E-50
嘷嘷嘷嘷
E-50
嘷嘷嘷嘷
E-51
嘷嘷嘷嘷
Security Lock
E-51
嘷嘷嘷嘷
Status
E-52
嘷嘷嘷嘷
Factory Default
E-52
嘷嘷嘷嘷
Lamp Timer Reset
E-52
嘷嘷嘷嘷
嘷 嘷 嘷
嘷 嘷 嘷
Resolution
E-53
嘷
Frequency
E-53
嘷
Lamp Timer
E-53
嘷嘷嘷嘷
Input Signal
Menu Operation Method
E-40
Image
• Perform this operation while projecting the picture for which the adjustment/setting will be made.
• Select the menu name “Image”.
See “Menu Operation Method” on Page E-33 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-38.
Brightness / Contrast / Color / Tint / Sharpness
Picture qualities such as brightness and contrast will change depend-
ing on the whether the room is bright or dark. Please adjust to suit your
preference.
Select the desired item name and then adjust with the SELECT 왗왘 buttons.
Item Name
Brightness
Contrast
Color
Tint
Sharpness
SELECT 䊴 Button SELECT 䊳 Button
Darker
Less contrast
Less dense color
More red
Softer image
Brighter
More contrast
Denser color
More green
Sharper image
Note:
* The adjustment values of the adjustable items are stored according to input source.
* “Tint” can only be adjusted when inputting NTSC composite/S-Video signals or
component signals.
Picture Adj. / Fine Picture / H Position / V Position
Usually, automatic adjustment is performed at the time of signal selec-
tion, but when automatic adjustment is not effective, these adjustments
can be performed.
Note:
When the image extends beyond the boundaries of the screen or is smaller than the
screen, check that the “View”
→
“Aspect” setting is set to “Auto”. See “Aspect” on
Page .E-45
Picture Adj. (Picture Adjustment)
Adjust this when bright and dark vertical bands appear on the screen.
Select the “Picture Adj.” item name and adjust with the SELECT 왗왘 buttons
so that the vertical bands disappear and brightness becomes uniform across
the screen.
E-41
Fine Picture
Adjust this when the picture shows a lack of color fidelity or flickering.
Select the “Fine Picture” item name and adjust with the SELECT 왗왘 buttons
so that the lack of color fidelity or the flickering disappears.
Image
H Position
Adjust this when the picture is shifted to the left or right.
Select the “H Position” item name and adjust with the SELECT 왗왘 buttons.
V Position
Adjust this when the picture is shifted up or down.
Select the “V Position” item name and adjust with the SELECT 왗왘 buttons.
Reset
This function resets (i.e., returns to the standard settings) the adjust-
ment/setting value of the “Image” menu name.
A press of the ENTER button forces the reset.
Note:
* The item name “Fine Picture” at the time of RGB input will not be reset.
* “Reset” of the menu name “Image” can be reset for each input source.
* To reset the adjustments/settings of all the menu items (while noting that there are some items that cannot be reset), see “Factory Default”
on Page E-52.
E-42
Color
• Do the following operation while displaying the image you want to adjust or set.
• Select the menu name “Color”.
See “Menu Operation Method” on Page E-33 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Pages
E-38.
Gamma
Gamma corrects the proportion of change of the dark portions from the
bright portions of the input signal.
Set this to reproduce natural color tone or to distinctly project a per-
sonal computer picture in a bright conference room.
Select the “Gamma” item name and select the setting contents with the SE-
LECT buttons.왗왘
Normal ....... Correction with standard settings
Natural ........ Corrects for natural color tones
Real ............ Corrects with emphasis on brightness
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “Gamma” adjust-
ment item is displayed in gray and cannot be selected or adjusted.
Quick Color Adj.
Select the preset color mode.
Select the “Quick Color Adj.” item name and select the setting contents with
the SELECT 왗왘 buttons.
Color ........... Select this to prioritize color.
Standard ..... Select this to prioritize brightness.
* When “Color” or “Standard” is selected, the “Gamma”, “Color Temp.” and “White” adjustment
items are displayed in gray and cannot be selected or adjusted.
Custom ....... “Gamma”, “Color Temp.” and “White” adjustment items can be selected
and adjusted
* The selected values for the different adjustment items are stored in the memory so the desired
color adjustments can be set.
E-43
Color Space
Set this function when a component signal (YPbPr) is projected and the
image is extremely red or extremely green.
Select the item name “Color Space” and use the SELECT buttons to왗왘
select a color space setting that provides a normal image.
Selection contents at the time of YPbPr input
BT.709, SMPTE240
Note:
* When the component signal undergoes conversion processing to red, green,
and blue which express the image of the projector, the correct color cannot be
reproduced unless a system compliant with the color difference conversion sys-
tem of the input signal is used. Color Space serves to make this selection.
* The color space can only be adjusted with high definition TVs.
Color
Color Temp.
The screen color is affected by the color of the illumination and other
extraneous light.
This function adjusts the white, which is the reference color for video
equipment, and improves the quality of color reproduction. Adjustment
can also be used to enhance skin colors.
Select the item name “Color Temp.” and select the setting contents with the
SELECT buttons.왗왘
Low ............ Produces warm whites (reddish)
Medium ...... Produces warm whites (yellowish)
Normal ....... Produces the white of sunlight
High ............ Produces cool whites (bluish)
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “Color Temp.”
adjustment item is displayed in gray and cannot be selected or adjusted. See “Quick
Color Adj.” on E-42.
White
When projecting, this function is used to emphasize the whites of text or
diagrams on the personal computer.
Select the item name “White” and use the SELECT buttons to select the왗왘
setting contents.
Select the desired degree of white from among “Low”, “Medium”, and “High”.
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “White” adjust-
ment item is displayed in gray and cannot be selected or adjusted. See “Quick Color
Adj.” on E-42.
E-44
White Balance
This function automatically adjusts the black level and the white level of
the analog RGB input signal to suit the personal computer.
1 Select the item name [White Balance] and press the ENTER button.
The display will change to [Input Black Signal].
2 The screen background color of the connected personal computer
will be set to black.
3. Press the ENTER button. The display will change to [Adjusting Black]
and the black level will be adjusted.
4 The adjustment of the black level is completed and the display
changes to [Input White Signal].
5 The screen background color of the connected personal computer
will be set to white.
6 Press the ENTER button. The display will change to [Adjusting White]
and the white level will be adjusted.
[White balance complete] is displayed for a while and the adjustment is
completed.
Color
E-45
View
• Perform this operation while projecting the picture for which the adjustment/setting will be made.
• Select the menu name “View”.
See “Menu Operation Method” on Page E-40 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-45.
Aspect
This function sets the horizontal and vertical picture proportions of the
input signal.
Select the item name “Aspect” and select the setting contents with the SE-
LECT 왗왘 buttons.
Filter
This function sets the sharpness when the input signal is adjusted to
the resolution of the projector and enlarged or reduced.
Select the item name “Filter” and select the setting contents with the SELECT
왗왘 buttons.
Smaller numerical values result in a sharper picture and larger values result in
a softer picture. Please select your desired setting value.
Video Signals
Auto ............ While maintaining the aspect ratio, projects a full screen
so that no portions extend beyond the boundaries of the
screen. The top and bottom of the 16:9 image becomes
black.
Wide ........... Projects to fill the full width with the entire image at 16:9.
(This feature is used to project a squeezed image in a
proper aspect ratio.)
Zoom .......... Projects only the 4:3 portion within 16:9 image to fill the
screen. (Portion that extend off screen is cut.)
Aspect ratio selection Auto Wide Zoom
4:3 screen
16:9 screen
Personal Computer Signal
Auto ............ Automatically enlarges or reduces the image to project
a full screen in a ratio of 4:3
Direct .......... Maintains the aspect ratio and projects a picture of the
maximum displayable size
Real ............ Projects the input signal without pixel conversion
Input Signal Auto Direct Real
The setting is higher
than the display reso-
lution of the projector.
The setting is lower
than the display reso-
lution of the projector.
See “Selection of Aspect Ratio” on Page E-29 for diagrams of projection screen
images that correspond to the input signals.
Note:
Please note that using this monitor for the purpose of commercial gain or the at-
traction of public attention in a venue such as a coffee shop or hotel and projecting
a 4:3 screen in wide mode or leaving a squeezed screen as a compressed image
raises concern about the infringement of the copyright holder’s rights which are
protected by copyright law.
Note:
When selection has been made for the “Real” setting of the personal computer
signal (i.e., when the input signal and the projector display resolution are high) and
the “Zoom” setting of the video signal, pressing the SELECT
왖왔왗왘
buttons on
the remote control will permit movement of the display position. Note that there will
not be any movement when the menu or the quick menu is displayed.

Produkt Specifikationer

Mærke: Toshiba
Kategori: videoprojektorer
Model: TDP-P7

Har du brug for hjælp?

Hvis du har brug for hjælp til Toshiba TDP-P7 stil et spørgsmål nedenfor, og andre brugere vil svare dig


videoprojektorer Toshiba Manualer

Toshiba

Toshiba TLP-WX200 Manual

13 Maj 2024
Toshiba

Toshiba NPS10A Manual

2 Maj 2024
Toshiba

Toshiba TLP-MT3E Manual

19 April 2024
Toshiba

Toshiba TLP-S40 Manual

10 April 2024
Toshiba

Toshiba TLP-781U Manual

14 Marts 2024
Toshiba

Toshiba TLP-X150 Manual

9 Marts 2024
Toshiba

Toshiba TLP-680U Manual

5 Marts 2024
Toshiba

Toshiba TLP-MT7E Manual

25 Januar 2024
Toshiba

Toshiba TXP-651 Manual

20 Januar 2024
Toshiba

Toshiba TDP-TW350 Manual

16 Januar 2024

videoprojektorer Manualer

Nyeste videoprojektorer Manualer

Epson

Epson ELPCB03N Manual

13 Marts 2025
InFocus

InFocus Genesis IN0024ST Manual

26 Februar 2025
BenQ

BenQ W2720i Manual

26 Februar 2025
InFocus

InFocus Genesis IN0026SL Manual

25 Februar 2025
Nebula

Nebula Capsule Air Manual

21 Februar 2025
Sony

Sony Bravia VPL-XW8100 Manual

21 Februar 2025
Christie

Christie Inspire DWU760-iS Manual

21 Februar 2025
Acer

Acer V65Wp Manual

18 Februar 2025
NEC

NEC NP-PA804UL Manual

18 Februar 2025
Eurolite

Eurolite LED PARty Manual

18 Februar 2025