Vtech VC7003 Manual

Vtech Overvågningskamera VC7003

Læs nedenfor 📖 manual på dansk for Vtech VC7003 (4 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/4
Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This manual has instructions on how to
set up and register your new sensor. For
instructions on sensor settings, see the
user’s manual that came with your ULE
compatible products. Visit
www.vtechcanada.com for a list of the
latest ULE compatible products.
You may also view or download the online
User’s manual of the respective product
for a full set of installation and operation
instructions at www.vtechcanada.com.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Motion Sensor overview
1 – Screw cover
Slide to open or close the screw cover
to reveal the battery compartment
case and button.PAIRING
2 – Back cover
3 – LED light
Briefly flashes red when the sensor is
first powered on.
Flash red once, when motion is
detected.
Flashes green when the sensor is in
registration mode.
4 – Motion detector
5 – PAIRING button
Press and hold to enter the
registration mode.
6 – Battery compartment case
•
•
•
•
•
Before use
Open the battery compartment case
Slide to open the screw cover and
unscrew the screw until the battery
compartment case is separable from the
back cover.
Separate the battery compartment case
from the back cover.
Install Motion Sensor Battery
NOTES
Use only CR123A Lithium Battery.
When inserting battery, ensure polarities are
correct.
For proper operation, use battery within the
following temperature range: 0°F (-18°C) and
120°F (49°C).
Pull the ribbon tightly across the battery
compartment.
Insert the battery into the battery
compartment.
Add and register a sensor
Your new Motion Sensor can be VC7003
registered to any ULE compatible product
Register each sensor individually to the
respective ULE compatible product before
use.
1.
2.
•
•
•
1.
2.
Register a Motion Sensor:
If you have just inserted the battery,
wait for the red LED to stop flashing.
Enter the registration mode by selecting
the option for adding a sensor to your
ULE compatible product. Refer to the
user’s manual of your ULE compatible
product for more detailed instructions.
Use a narrow pointed object such as
a pen to press and hold the PAIRING
button on the Motion Sensor, until the
LED light at the front side flashes green.
The sensor is now registering to the
ULE compatible product.
The registration process takes about 90
seconds to complete. When this registration
process completes, the green LED light
on the sensor will remain steadily on for
approximately two seconds then, will turn off.
If registration fails, remove battery from the
sensor and wait for a few seconds. Then,
re-install battery and wait until the red LED
stops flashing. After that, begin registration
process again.
NOTES
You can also download online User’s manuals at
www.vtechcanada.com.
If you are going to mount the sensor with screws or
mounting bracket, the back cover has to be mounted
before you assemble the battery compartment
case back to it (see Mount the sensor).
Replacing a sensor
If you have purchased this new VC7003
accessory sensor to replace an old sensor,
you must deregister the registered sensor
first, and then register this new sensor to your
ULE compatible product.
Deregister a sensor or all sensors:
Refer to the User’s manual of your ULE
compatible products to deregister a sensor
or all sensors.
1.
2.
3.
•
•
•
Motion detection
The Motion Sensor detects motion with
one-minute cool off time. Once motion is
detected, the sensor will start detecting
motions again only after one minute.
The Motion Sensor is more sensitive in
detecting motions crossing the space in front
of the sensor than that moving towards the
sensor.
The Motion Sensor can detect motion
occurring at distances up to 40 feet (12
meters) when it is mounted at a height of 7.9
feet (2.4 meters).
It is recommended to mount the sensor at the
height between 6.2 feet (1.9 meters) and 7.5 feet
(2.3 meters) for optimal detection coverage.
For motion detection of babies or pets:
If you use the Motion Sensor only to detect
the motion of babies or pets, you can mount
the sensor at a lower position to shorten
the minimum distance before reaching the
detection area. It is recommended to mount
it at the height for optimal 3.3 feet (1 meters)
detection of babies and pets.
NOTE
The numerical values in the illustrations are for
conceptual reference only. The actual angles
and distances may vary upon the change in the
mounted height of the sensor.
•
Check the sensor before use
1. Place the sensor about 3.3 feet (1 meter)
from the ULE compatible product.
2. Waive your hand or walk across the area
in front of the sensor.
You will receive alerts at your ULE
compatible product. Refer to the
Installation guide or user’s manual of
your ULE compatible product for the
sensor alerts.
The LED light on the Motion Sensor will
flash red once.
NOTE
Once motion is detected, the sensor will only
start to detect motion again after one minute.
When you have received alerts already, you will
only receive alerts again for motion detected
after one minute.
•
•
•
Test the sensor signal strength
You can mount the Motion Sensor at a
location where family members or unwanted
visitors are likely to be coming and going.
1. Take the sensor to the desired mounting
location and then, hold it at the desired
height (Refer to Motion detection
section). Use adhesive tape to hold the
sensor temporarily in place.
2. Enter the signal checking or testing mode
at your ULE compatible product to test the
sensor signal strength.
3. Waive your hand or walk across the area
in front of the sensor again and check
whether a good signal is received at your
ULE compatible product.
NOTES
Once motion is detected, the sensor will only
start to detect motion again after one minute.
When you have received alerts already, you will
only receive alerts again for motion detected
after one minute.
If there is no alert received when you walk
across the area in front of the sensor, move
your ULE compatible product closer to the
mounting location or move the sensor closer to
the respective product.
Depending on surroundings and obstructing
factors, like walls or cabinets, the sensor may
not transmit to the ULE compatible product
properly.
•
•
•
VC7003
Accessory Motion Sensor
for use with
ULE certified systems*
Motion Sensor
Mounting bracket
on mounting base
with screw
Lithium battery
Mount the sensor
NOTES
This sensor must be mounted vertically on wall. Do not mount the Motion Sensor in a horizontal
orientation, or flat on the ceiling.
Make sure the mounting surface is clean. A textured surface or any imperfections to a smooth surface
can keep the mounting tape from making a strong bond.
This device detects or performs better when provided with a constant and stable environment.
Avoid placing the sensor at a location which faces direct sunlight, or exposes to areas that may change
temperature rapidly, or where there are air ducts or substantial airflows.
The recommended mounting height for motion detection of adults is between and6.2 feet (1.9 meters)
7.5 feet (2.3 meters) 3.3 feet (1 meter), and that for babies or pets is about .
If you drill the holes into an object other than a stud, insert the screw anchors into the holes and tap
gently on the ends with a hammer until the screw anchors are flush with the wall or ceiling.
TIP
You can choose to mount the sensor with the mounting tape first. Remove the mounting tape and use
screws later if you decide to mount it at that location for long term.
•
•
•
•
•
•
User’s
manual
User’s manual
2 3
4
1
Screw for
mounting
brackets x 2
Screw for
back cover x 3
Mount on the wall - with fixed angle
Mount on the wall - with rotated detection angle
1
2 3
5
f
(Optional)
Insert screw
anchors if
necessary.
* Visit for the latest ULE compatible products.www.vtechcanada.com
Anchor for
back cover x 3
Anchor for
mounting
brackets x 2
Double-sided
mounting tape
Mount with tape
Mount on the wall - with fixed angle
Mount with screws
4 5
2
3
1
Drill a hole
here.
Up to 34.4 feet
(10.5 meters)
Side view
Detection
area
78o
Top view
87o
Detection area
1.3 feet
(0.4 meter)
10o
Height: 6.9 feet (2.1 meters)
Height: 6.9 feet (2.1 meters)
Side view
Detection
area
78o
Top view
87o
Detection area
0.7 feet
(0.2 meter)
10o
Height: 3.3 feet (1 meter)
Up to 16.4 feet
(5 meters)
Height: 3.3 feet (1 meter)
TIP
You can rotate the sensor 45 degree, and then mount the sensor next to the corner of wall for optimal
detection coverage.
•
NOTE
This product requires professional installation.•
2
1
This screw should only
be fully secured after you
adjusted the angle.
Unscrew first.
4
5 6 7 Tighten the screws after
you slided the sensor
over them.
(Optional)
Insert screw
anchors if
necessary.
Tighten
the scew.
Tighten
the scew.
Tighten
the scew.
2
1
Go to www.vtechcanada.com
to register your product for
enhanced warranty support and
the latest VTech product news.
User’s manual
(Canada version)

Produkt Specifikationer

Mærke: Vtech
Kategori: Overvågningskamera
Model: VC7003

Har du brug for hjælp?

Hvis du har brug for hjælp til Vtech VC7003 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Vtech Manualer

Vtech

Vtech VC7003 Manual

14 December 2024
Vtech

Vtech VC7002 Manual

13 December 2024
Vtech

Vtech VC7001 Manual

13 December 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Vimar

Vimar ELVOX 693T Manual

15 December 2024
D-Link

D-Link DCS-8330LH Manual

13 December 2024
I-PRO

I-PRO WV-S66300-Z3N Manual

13 December 2024
I-PRO

I-PRO WV-X66600-Z3LK Manual

13 December 2024
I-PRO

I-PRO WV-S66300-Z4 Manual

13 December 2024
I-PRO

I-PRO WV-S61602-Z3 Manual

13 December 2024
I-PRO

I-PRO WV-S66300-Z4L Manual

13 December 2024
I-PRO

I-PRO WV-S66700-Z3LN Manual

13 December 2024
I-PRO

I-PRO WV-S66700-Z3N Manual

13 December 2024
I-PRO

I-PRO WV-U65301-Z1G Manual

13 December 2024