Watts BT-DPRF-02 Manual

Watts Thermostaat BT-DPRF-02

Læs nedenfor 📖 manual på dansk for Watts BT-DPRF-02 (2 sider) i kategorien Thermostaat. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

PPLIMW15175Ba

BT-DPRF-02

IMPORTANT!

Before starting work the installer should carefully read this

Installation & Operation Manual, and make sure all instructions

contained therein are understood and observed.

- The thermostat should be mounted, operated and maintained

by specially trained personnel only. Personnel in the course of

training are only allowed to handle the product under the

supervision of an experienced fitter. Subject to observation of

the above terms, the manufacture shall assume the liability for

the equipment as provided by legal stipulations.

- All instructions in this Installation & Operation manual should

be observed when working with the controller. Any other

application shall not comply with the regulations. The

manufacturer shall not be liable in case of incompetent use of

the control. Any modifications and amendments are not allowed

for safety reasons.

The maintenance may be performed by service shops

approved by the manufacturer only.

- The functionality of the controller depends on the model and

equipment. This installation leaflet is part of the product and

has to be obtained.

APPLICATION

- The thermostats range “BT-DPRF-02” has been developed to

control and manage all type of Electrical heating system or

materials.

- The controllers have been designed for use in residential

rooms and industrial facilities.

Verify that the installation complies with existing regulations

before operation to ensure proper use of the installation.

Please find the Watts Vision system configuration

documentation on: http://www.wattselectronics.com

Table des matières

1 Presentation

1.1 Keyboard

1.2 LED & Display

2 First installation

2.1 Batteries installation

2.2 Time and Date adjustment

2.3 RF installation

2.4 Starting

3 Working mode definition

3.1 Manual mode Comfort

3.2 Manual mode ECO

3.3 OFF mode

3.4 Automatic mode

3.5 Program mode

3.6 Holiday mode

3.7 Timer mode

3.8 Reversible mode

4 Special functions

4.1 Key lock

4.2 Open window function

4.3 Humidity measurement (*)

4.4 Visualization

5 Parameter's menu

6 Technical characteristics

7 Troubleshooting & Solution

8 Advanced Installer's parameter menu

1. Presentation

Electronic programmable thermostat with LCD display specially

designed to control different type of heating systems.

It will be your best partner to optimize your energy consumption

and increase your comfort.

- Modern design with soft touch material

- Wireless Bidirectional communication 868 MHz

- “Easy program creation” function

- Weekly programmable by step of 30min

- Temporary override function

- Holiday or Reception function

- EEPROM nonvolatile memory

- 2 AAA batteries

- 2 parameter menus (User and Installer)

- Humidity measurement (*)

In option

External sensor with several possibilities of regulation. (Floor,

combined…)

1.1. Keyboard

Left Navigation key (◄)

Right navigation key (►)

Escape key ( )

Edition key ( )

1.2. LED & Display

LED Color when backlight is lit up:

Red Fix: Heating demand (**)

Green Fix : Cooling demand (**)

Green flash: validation is required

Red flash: Error on sensor or batteries

1: Current day of the week (1=Monday,...)

2: Operating mode menu (active mode is framed).

3 4: Program number or parameter number if “ ” is

displayed.

4: Installation Parameter menu.

5: RF transmission logo.

6: Type of sensor used and temperature displayed.

Regulation => Internal sensor.

Regulation => Floor sensor.

(Only available with receiver)

Regulation => Internal sensor with Floor

limitation.(Only available with receiver)

Regulation => outside temperature measured by external

sensor (connected on the back of thermostat)

Humidity value

7: Low batteries indicator

8: °C or °F unit indicator

9 6: Setting or measured temperature if “ ” is displayed.

Parameter value if “ ” is displayed. 4

10: Cooling demand indication (**)

11: Heating demand indication (**)

12: Temporary override function activated

13 4: Time or parameter title if “ ” is displayed

14: Program of the current day (the current time bar blinks)

15: Pictogram for program creation, program state in normal

operating mode.

16: Key lock indicator.

2. First Installation

This section will guide you to set up your thermostat for the first

time.

2.1. Batteries installation

- Open the two side’s covers and Insert the 2 AAA Alkaline

supplied batteries (or remove the small protection sticker if the

batteries are already installed in the compartment)

- Close the two side’s covers

- Now your thermostat will propose you to adjust the current

time and date

2.2. Time and Date adjustment

Each time a value blinks, you can adjust it with the and (-) (+)

keys, once the value is chosen, validate it with the key. (OK)

The thermostat will jump automatically to the next value.

Remark: you can always come back to the previous value by

pressing the escape key . ( )

List order of the time and date adjustments:

Time and day:

Adjustment of the hours,

Adjustment of the minutes

Adjustment of the day (1 = Monday)

Date:

Adjustment of the day number

Adjustment of the month number (01 to 12)

Adjustment of the year

Then the message “ ” and blinking green LED appears, Save

press to validate the adjusted time and date. (OK)

You can always reach the time and date adjustments, by

pressing and maintaining the edition key during 2 seconds ( )

in normal operating modes.

Remark: when a central (BT-CT02) is linked to your

installation, thermostat will use the Time set in the Central

2.3. RF installation

Please have a look at the list of all receivers compatible with

this thermostat in Technical Characteristics section.

2.3.1. With receivers

- First of all to configure your thermostat with the receiver, you

must put your receiver in « » mode (refer to the receiver RF init

leaflet, only the RF receiver of the same range are

compatibles).

- Now on the thermostat press and maintain the edition key

( ) during 5s, then the parameter « RF ini » must be

display.

The thermostat will send now the radio configuration signal to

the receiver.

- After few seconds the thermostat and receiver should exit by

their self the mode, this is the normal procedure to RF init

confirm a correct pairing.

- Now you can check the RF distance, go to the room which

must be regulated. Put your thermostat on the final position (On

the wall or table...), then put the thermostat in Comfort mode

(setting temperature position 37°C). Close the door and go to

the receiver to check if the new status of the thermostat has

received.

- Now return to the thermostat and switch off it. Check on the

receiver again if it’s also switched off.

If the RF signals were received correctly, adjust your setting

temperature as you want.

If the RF signals weren’t received correctly, check the

installation (Receiver position, distance...) or restart the RF init

rules to be sure.

Remark: To make the installation easier, it will be better to

have the thermostat near to the receiver during the

configuration mode. (A minimal distance of 1 meter must be

respected)

2.3.2. Case of Central (BT-CT02)

Procedure is the same as in 2.3.1 but link is done with central

(BT-CT02). At this moment, Central creates a new zone.

2.4. Starting

The thermostat is now ready to work. The default working

mode is Manual Comfort

At any time, when the backlight is extinct, press the (OK)

key to lit-up the backlight.

3. Working mode definition

Your thermostat has several different working modes to allow

you to adjust your unit according to your life habitudes.

To change the working mode,

open the small center cover to

have access to the navigation

keys or . Move the frame (◄) (►)

cursor on the desired working

mode and press to enter in (OK)

the operating mode you have

chosen.

3.1. Manual mode Confort

Manual working mode, the comfort setting temperature will be

followed all the time.

By pressing or keys, the comfort setting temperature (-) (+)

starts to blink and can be adjusted.

3.2. Manual mode ECO

Manual working mode, the reduced setting temperature will be

followed all the time.

By pressing or keys, the reduced setting temperature (-) (+)

starts to blink and can be adjusted.

Remark: In cooling mode, Reduced mode acts like the OFF

mode (system is stopped)

3.3. OFF mode

Use this mode if you need to switch off your installation.

Be Careful: In this mode your installation can freeze.

At any time, when display is off, press on the key to (Ok)

display a few seconds the current temperature and time.

Remark: To restart your installation, use the navigation keys

(◄) (►) or .

3.4. Automatic mode

In this mode the thermostat will follow the chosen program

(Built-in or customized) according to the actual time and the

Comfort and Reduced setting temperatures.

By default, mode automatic

follows the standard built-in

program “ ”: P1

Monday to Friday

Saturday and Sunday

Note:

You can customise your program. See the next part “Working

mode definition Program” chapter “ ” for more explanation.

You can easily override temporarily the current program by

pressing or . The thermostat jumps to Timer mode in (-) (+)

which you select a setpoint and a time. The thermostat returns

automatically to the Automatic mode at the end of the time.

3.5. Program mode

When you enter in the Program mode, the first operation is to

choose the program number with or keys. (-) (+)

You can choose between a built-in program to or a user P1 P9

program to . U1 U4

If you chose a Built-in program to , P1 P9

You can only see and chose the program.

P1: Morning, Evening & Weekend

P2: Morning, Midday, Evening & Weekend

P3: Day & Weekend

P4: Evening & Weekend

P5: Morning, Evening (Bathroom)

P6: Morning, afternoon & Weekend

P7: 7H – 19H (Office)

P8: 8H – 19H & Saturday (Shop)

P9: Weekend (Secondary house)

- Use the navigation keys or to view other days of the (◄) (►)

program.

- Press the key to confirm your choice and come back to (OK)

the main screen (in AUTO mode)

If you chose a user program U1 to U4, you can also customise

it.

Default setting:

U1, U2, U3, U4 = ECO all week

- Press on the edition key to customise a user program. ( )

Symbols and explanation for program creation:

First step of the day ( Comfort temp.)

The wakeup hour need to be adjusted.

Middle step of the day ( Reduced temp.)

The leaving hour need to be adjusted

Middle step of the day (

Comfort temp.)

The comeback hour will need to be adjusted

Last step of the day ( Reduced temp.)

The sleeping hour need to be adjusted

- The program step is 30 minutes

- Each time a value or icon blinks you are invited to make a

choice with or keys, once the choice is made press the (-) (+)

(OK) key to jump to the following step.

- The program creation will always start with the day 1

(Monday).

Once you have pressed the key, the following display will ( )

appear:

Now you are invited to adjust the hour of the first step of the

program with or , (-) (+)

Press to validate and go to the following step. (OK)

Now you are invited to choose the type of the next step of the

program (blinking icons). Two choices will be possible:

- 1

choice is to choose the sleep icon. (End of the day)

- 2

choice is to choose the leaving icon, to add one step to the

program during the day.

When the choice is made, press to validate. Then you can (OK)

adjust the step hour with or , (-) (+)

When step hour is set press to jump to the next step. (OK)

You will be directly invited to adjust with or the hour of (-) (+)

the comeback step.

Press to validate and go to the following step. (OK)

You are again invited to choose the type of the next step of the

program (blinking icons), two choices will be possible:

- 1

choice is to choose the sleep icons. (End of the day)

- 2

choice is to choose the leaving icons, to add another step

to the program during the day.

When the choice is made, press to valid and you can (OK)

adjust the hour of this step with or , (-) (+)

Press to validate and finish the edition of the first day. (OK)

Now you can choose to copy the program day just created to

subsequent days

Change the choice “ ” or “ ” with or and validate Yes no (-) (+)

your choice with . (OK)

- If you select “ ”, you will be invited to create a program for no

Tuesday (repeat the previous method to build it.)

- If you select “ ”, you will have the possibility to copy the Yes

program to the following day (on Tuesday on Wednesday... up

to the last day of the week (7=Sunday).

When you press on the last day (7=Sunday) you will be (OK)

invited to “ ” your program. SAVE

Then the message “ ” and blinking green LED appears: Save

Press key to save your program and return to (OK) AUTO

operating mode following your user program.

Press the escape key to erase your user program ( )

changes and come back to operating mode.

Remark: when a central is linked to your installation, program

is done on the Central.

3.6. Holiday mode

The Holiday mode allows you to set the anti-freeze temperature

for a selected number of days

You can adjust, the duration in day “ ” with or , pressd (-) (+)

(OK) to start (Adjustable 1 to 44 days).

The anti-freeze setting temperature is fixed and can be

adjusted in the parameter menu number , refer to 06 HG‘ ’

chapter 5.

The logo will blink and the number of days left is displayed

until the end of the period.

If you want to stop the Holiday function before the end, set

the duration period to “ ” with key. no (-)

Remarks:

- In cooling mode, this mode acts like an OFF mode

- When a central is linked to your installation, this mode is

permanent (or set directly via the Central BT-CT02)

3.7. Timer mode

The Timer mode allows you to adjust, the temperature for a

special time. After this time, thermostat will go to older current

mode.

- You can first adjust, the duration in hours “H” if below 24H,

then in day “ ” with or , press to validate. d (-) (+) (OK)

(Adjustable 1 Hour to 44 days)

Current

stage of the

program

Program

followed

Currrent

Produkt Specifikationer

Mærke:	Watts
Kategori:	Thermostaat
Model:	BT-DPRF-02

Har du brug for hjælp?

Hvis du har brug for hjælp til Watts BT-DPRF-02 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Thermostaat Watts Manualer

Watts BT-DPRF-02 Manual

23 Juli 2024

Thermostaat Manualer

Nyeste Thermostaat Manualer

Drayton RTS2 Manual

16 September 2024

AWB ExaControl VM-1 Manual

16 September 2024

Siemens RAA31 Manual

16 September 2024

Honeywell SMHOM8610KIT Manual

15 September 2024

Theben RAM 797 HF set 4 Manual

15 September 2024

Theben RAMSES 725 Thermostaat Manual

15 September 2024

Theben RAMSES 798 Thermostaat Manual

15 September 2024

Theben RAMSES 707 Thermostaat Manual

15 September 2024

Theben RAMSES 746 Thermostaat Manual

15 September 2024

Theben RAM 785 Manual

15 September 2024