Zoom DOCSIS 3.0 Manual

Zoom Router DOCSIS 3.0

Læs nedenfor 📖 manual på dansk for Zoom DOCSIS 3.0 (1 sider) i kategorien Router. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Problem: I have connected a router to the cable modem but cannot access the

Internet or send or receive email.

44 Plug the modem’s power cube into an outlet and then into the modem’s POWER jack. It

may take several minutes for the modem to register with the cable system. If the

modem’s front panel STATUS, US, and DS lights do not stay on steady after a

reasonable amount of time, go to Troubleshooting.

C A B L E M O D E M Q U I C K S T A R

C A B L E M O D E M Q U I C K S T A RC A B L E M O D E M Q U I C K S T A R T

Package Contents Solution: ¾ Connect the cable modem directly to a PC following the instructions

above. If the cable modem works properly when connected directly to

your computer, most likely the problem is caused by the router’s

configuration or installation.

• Cable Modem

• Modem Stand

55 Power-up the router. Wait for the router to complete its power-up sequence. The

modem’s LINK light should come on.

• Power Cube

• Ethernet Cable ¾ First try shutting down and restarting each computer connected to the

router. Power cycle your cable modem and allow time for it to

resynchronize with the cable system.

66 You may need to restart some or all of the computers attached to the router.

System Requirements

77 You should follow any directions that your cable provider has given to you. Your cable

company may instruct you to tell them your cable modem’s MAC address after you

complete the hardware installation.

• You need to connect the cable modem to a cable modem service that uses any of the

popular DOCSIS standards – 3.0, 2.0, 1.1, or 1.0. If you need to get cable modem

service, please speak with your cable service provider.

¾ You may also need to check that the DHCP client on the router’s WAN

port is enabled. If you need help, look in your router’s manual or

contact your router manufacturer.

88 Using a computer connected to the router, open the computer’s browser and go to a

website to check that the connection between your cable modem and router is working

properly.

• You need to connect a computer or router to the cable modem using an Ethernet cable.

The computer can be a Windows, Macintosh, or Linux computer. The router must have

one or more Ethernet ports, and may include wireless capability. Instructions for making

this connection are below.

¾ If that does not solve the problem, you may need to contact your cable

service provider and give them the MAC address of the router’s WAN

port.

Note: If you have a problem connecting to the router, please test the cable connection

by connecting the cable modem directly to a PC by following the instructions in the

previous section. If the cable modem worked properly when connected directly your

computer, most likely the problem is caused by the router’s configuration or installation.

Check your router’s documentation for help.

Getting Help

Locate Your Ethernet MAC Address If you need assistance, please go to www.zoom.com

Your cable company may ask for your cable modem’s MAC address. This is on the bottom

of your cable modem. You may want to write it down here for quick reference:

___________________________________.

and select Technical Support for help

via our Web SmartFacts system, email or phone.

Safety Issues & Warnings

Your cable service provider may provide a cable modem starter kit

Some cable service providers supply a cable modem starter kit that can be useful when

you install your cable modem. The kit may include a coaxial cable for connecting

between a wall jack and your cable modem. (These are also available at most

electronics retailers.) The kit will include instructions, and may also include a CD with

software. If you receive a kit like this, we recommend that you read the kit’s

instructions and use them to install your Zoom cable modem. This cable modem is

DOCSIS 3.0 certified by CableLabs, and connects like a normal cable modem. You will

need to plug in the cable modem’s power cube, connect to cable modem service using

a coaxial cable, and connect the included Ethernet cable between the cable modem

and a computer or router.

Power CATV Reset ETH

How to connect to a computer if you don’t have a cable company’s starter kit

11 Make sure that your computer is on.

22 Plug one end of the Ethernet cable into the modem’s ETH jack and plug the other end

into your computer’s Ethernet jack. The LINK light of the modem should be lit to show

the Ethernet connection.

33 Connect the modem to a coaxial cable for the cable service. The cable service is

carried on the same cables and connectors as your cable TV service.

¾ You can connect a coaxial cable between an open cable service wall jack

and the cable modem. (If no wall jack is open, you can use a coaxial T

connector.)

¾ Alternatively, there may already be a coaxial cable that is connected to

service and that has an open end for connecting to the cable modem.

44 Plug the power cube into an outlet and then into the modem’s POWER jack. It may take

several minutes for the modem to register with the cable system. If the modem’s front

panel STATUS, US, and DS lights do not stay on steady after a reasonable amount of

time, go to Troubleshooting.

55 You should follow any directions (including instructions for any software installation)

that your cable provider has given to you. Your cable company may instruct you to tell

them your cable modem’s MAC address after you complete the hardware installation.

66 Now that you have installed your Zoom cable modem and it has synchronized itself with

the cable network, your cable modem can connect you to the Internet. Open your

browser and go to a familiar Web site to check that the cable modem is working.

Congratulations! Installation is complete.

How to connect your cable modem to a router (not a computer)

11 The router should not be plugged in or powered up. If it is, unplug it.

22 Plug one end of the Ethernet cable into the modem’s ETH jack and the other end into

the router’s WAN Ethernet jack, typically labelled WAN or Internet.

33 Connect the modem to the cable outlet.

¾ If you have a wall outlet cable jack: Connect one end of the coaxial cable to the

modem’s CABLE connector and connect the other end to the wall jack.

¾ If you do not have a wall jack: You should have coaxial cable entering your

house close to where you want to locate your cable modem. Connect the end of

this cable to the modem’s CABLE connector.

Please note the following:

WARNING: Risk of electric shock. Do not expose to water or moisture.

• You can position the cable modem horizontally or vertically. The vertical position benefits

from the modem stand. • The Broadband Residential Cable Modem is a high-performance communications

device designed for home and office environments.

• Do not block the modem vents in any way.

• Do NOT use the cable modem outdoors. Keep the cable modem in an

environment that is between 0°C and 40°C (between 32°F and 104°F).

• Do not place the modem near a heating or air conditioning duct, in direct sunlight, or

anywhere susceptible to drastic temperature changes.

• To avoid overheating the cable modem, do NOT place any object on top of the

cable modem.

Troubleshooting

Your Zoom cable modem has several lights on its front panel to help you monitor the

modem’s status.

• Do not restrict the flow of air around the cable modem.

• The manufacturer assumes no liabilities for damage caused by any improper use

of the cable modem.

Light Name Mode Status

Disclaimer

POWER Solid Power is on.

Zoom Telephonics, Inc. (hereinafter “Zoom”) assumes no liabilities with respect to the contents of this

document. Zoom also reserves the right to revise this document or update occasionally the content

hereof without any obligation to notify any person of such revisions or amendments. Specifications subject

to change without notice.

Blinking Modem is establishing a connection from the Internet to the

computer.

Solid Connection from the computer to the Internet is established.

(downstream) Dark Not scanning.

Regulatory Information

FCC

Blinking Modem is establishing a connection from the computer to the

Internet.

Solid Connection from the computer to the Internet is established.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and,

(2) This device must accept any interference received, including interference that may cause undesired

operation.

Dark Not scanning.

(upstream)

Blinking Modem is establishing a connection to the cable provider.

UL Listing

This product is UL-Listed and complies with all applicable electrical and fire safety requirements.

Solid Modem connection to the cable provider is established.

STATUS

Limited Warranty

Blinking Data is flowing between the computer and the Internet.

Zoom Telephonics, Inc. (hereinafter “Zoom”) warrants this product against defects in material and

workmanship for a warranty period of 2 years. This warranty applies to the original end-user purchaser.

Powered-up modem is connected to LAN device (e.g. computer,

router).

Solid

LINK

For all Zoom products other than software, Zoom will, solely at its option, repair or replace this product

with a functionally equivalent new or factory-reconditioned product during the warranty period. The

consumer will deliver the product to Zoom. All transportation risks and costs in connection with this

warranty service are the responsibility of the consumer.

Problem: I cannot access my Internet service or send or receive email.

Solution: All the modem’s front panel lights—LINK, STATUS, US DS (upstream),

(downstream), and POWER—must be solidly lit before your modem will let

you connect to the Internet. If they are not:

Zoom will replace software at no charge if there is a defect in materials or workmanship for a period of 30

days from date of original retail purchase, provided the defective software is returned to Zoom. Shipments

from Zoom will normally be via U.S. Mail. Software products supplied by Zoom are sold “as is,” without

warranty, either expressed or implied, as to function, application, merchantability, performance, and

quality.

Check all modem connections (power

, Ethernet, and cable modem line).

¾ Unplug your cable modem and then plug it back in.

¾ Restart your computer.

¾ Check to see that your cable TV is working.

Check with your cable service prov

ider to make sure that high speed

access is available and running.

Zoom is not responsible for incidental or consequential damages, and is not responsible for damages

resulting from the breach of any expressed or implied warranty. Zoom is not responsible for any costs of

recovering, reprogramming, or reproducing any programs or data stored or used with the Zoom products,

damage to property, and to the extent permitted by law, damages for personal injury.

¾ In rare instances, the cable signal may be weak or noisy. If this is the

case, call your cable service provider.

¾ If you are using your PC’s Ethernet port, check that this port is

functioning correctly. If you are using wireless, check that your wireless

connection is functioning correctly. Refer to its documentation if

necessary.

This warranty is in lieu of all other warranties, expressed or implied. We do not assume or authorize

assumption for us of any other warranty expressed or implied. Some states and countries do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusions may

not apply to you.

¾ Check that your Web browser is configured correctly. It should be set to

use a network connection (this might be called a Local Area Network or

broadband connection).

This warranty does not apply if the Zoom product has been damaged by accident, abuse, lightning or

other natural disasters, misuse or misapplication, or if it has been modified without the written permission

of Zoom, or if any serial number has been removed or defaced.

¾ Check that your computer’s network settings are configured correctly. A

Windows computer should have a local area connection that should

normally be Internet Protocol version 4, Internet Protocol version 6, or

TCP/IP; not AOL, Dial-up, or Adapter. A Macintosh computer should be

configured for Built-in Ethernet, and TCP/IP should be set to Using

DHCP.

This warranty shall not be applicable to the extent that any provisions of this warranty are prohibited by

any federal, state, or municipal law that cannot be preempted. This warranty gives you specific legal

rights, and you may also have other rights that vary from state to state or country to country.

Produkt Specifikationer

Mærke:	Zoom
Kategori:	Router
Model:	DOCSIS 3.0
Vægt:	190 g
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 40 °C
Strømforsyningstype:	Vekselstrøm/jævnstrøm
Dimensioner (BxDxH):	140 x 120 x 30 mm
Certificering:	FCC, CE, UL
DC-in-stik:	Ja
Firewall sikkerhed:	BPI+, EAE, SSD
LED-indikatorer:	Ja
Kompatible operativsystemer:	Windows OS\r\nMac OS
Intern:	Ingen
Modulation:	128-QAM,16-QAM,256-QAM,32-QAM,64-QAM,8-QAM,QPSK
Strøm-LED:	Ja
Filtrering af MAC-adresser:	Ja
Overholdelse af branchestandarder:	802.3, 802.3u, 802.3ab
Understøttede dataoverførselshastigheder:	10, 100, 1000 Mbps
Båndbredde:	6.4 GHz
Upstream datahastighed:	143.36 Mbit/s
Downstream datahastighed:	171.537 Mbit/s
Chipsæt:	Texas Instruments Puma 5 TNETC4830 (4X4)