AJA 12G-AMA Manual
AJA
Audio/video konverter
12G-AMA
Læs nedenfor 📖 manual på dansk for AJA 12G-AMA (38 sider) i kategorien Audio/video konverter. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/38
12G-AMA Mini-Converter
4-Ch Balanced Embedder/Disembeder
Version 1.0
Published June 9, 2020
Installation and Operation Guide
12G-AMA v1.0 2 www.aja.com
Notices
Trademarks
AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.
for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for
use with recorder, router, software and camera products. Because it matters.™ is a
trademark of AJA Video Systems, Inc. for use with camera products.
Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered trademarks of
AJA Video Systems, Inc.
AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, V2Analog™ and
V2Digital™ are trademarks of AJA Video Systems, Inc.
All other trademarks are the property of their respective owners.
Copyright
Copyright © 2020 AJA Video Systems, Inc. All rights reserved. All information in
this manual is subject to change without notice. No part of the document may be
reproduced or transmitted in any form, or by any means, electronic or mechanical,
including photocopying or recording, without the express written permission of AJA
Video Systems, Inc.
Contacting SupportAJA
When calling for support, have all information at hand prior to calling. To contact AJA
for sales or support, use any of the following methods:
Telephone +1.530.271.3190
FAX +1.530.271.3140
Web https://www.aja.com
Support Email support@aja.com
Sales Email sales@aja.com
12G-AMA v1.0 3 www.aja.com
Contents
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Base Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Fiber Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
12G-AMA Simplied Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6
12G-AMA I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
User Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mini-Cong Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Breakout Cable Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Default Operational Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DIP Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DIP Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Switches 4 and 5 Channel Mapping For Embedded Groups . . . . . . . . . . 11
Switches 6 and 7 Channel Mapping For Disembedded Groups. . . . . . . . 12
USB Control and Setup—Using AJA Mini-Cong . . . . . . . . . . . . . . . . . . 12
Acquiring Mini-Cong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Running Mini-Cong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operating Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Tabbed Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Input Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Audio-1 Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Analog Audio Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Analog Audio Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Audio-2 Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Packet Processing Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Analog Audio Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
About Audio Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Update Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 22
12G-AMA Family Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . . 27
Warranty and Liability Information . . . . . . . . . . . . . . . . . . . . 36
Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Governing Law and Language; Your Rights . . . . . . . . . . . . . . . . . . . . . . 36
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12G-AMA v1.0 4 www.aja.com
Chapter 1 – Introduction
Overview
The 12G-AMA is a 4-channel analog audio embedder/disembedder Mini-
Converter. It supports 12G-SDI input and output up to 4K/UltraHD single link, with
fiber I/O including LC and ST options.
Analog audio can be embedded and disembedded simultaneously. Audio
disembedding is always functional, providing four analog outputs. Audio
embedding is user selectable, on a channel pair basis, to either pass SDI
embedded audio or to embed input analog audio from the breakout cable.
Analog audio operating levels are selectable, via USB connection and Mini-Config
software.
The ability to pass incoming ancillary data makes it possible to embed up to
16 channels of audio by cascading four units. Horizontal ancillary data (HANC)
packets in compliance with SMPTE 291M can also be passed through or removed
at the input.
The 12G-AMA automatically detects and configures to the input video standard.
12G-SDI formats up to and including 4096x2160p 60 YCbCr 4:2:2 are supported
(see "Appendix A Specifications" on page 22 for a complete listing). SDI video
passes through the device with minimal delay. Pass through embedded SDI audio
supports up to 16 channels.
NOTE: 2048x1080p/PsF 29.97 and 30 formats support a maximum of 8 channels of
embedded audio.
12G-AMA v1.0 5 www.aja.com
Base Model
The base model—12G-AMA—does not include a fiber SFP module.
Fiber Options
Five variations of the 12G-AMA include LC or ST fiber options:
LC Options
• 12G-AMA-T, includes a 1310 nm Single Mode optical transmitter, Tx 1260 nm
(min), 1310 nm (typ), 1360 nm (max)
• 12G-AMA-R, includes a 1260 nm (min), 1620 nm (max) Single Mode optical
receiver
• 12G-AMA-TR, includes a 1260 nm (min), 1620 nm (max) Single Mode optical
receiver, and a 1260 nm (min), 1310 nm (typ), 1360 nm (max) Single Mode
optical transmitter
ST Options
• 12G-AMA-T-ST, includes a 1260 nm (min), 1310 nm (typ), 1360 nm (max) Single
Mode optical transmitter
• 12G-AMA-R-ST, includes a 1260 nm (min), 1620 nm (max) Single Mode optical
receiver
Features
• 12G, 6G, 3G, HD, and SD-SDI Embedder/Disembedder
• 4 Channel Balanced Analog Audio I/O
• Supplied breakout cable for balanced analog audio - XLR connectors.
• 1 x BNC 12G-SDI input
• 1 x BNC 12G-SDI output
• Fiber SFP models available
• Setup via DIP switch or PC/Mac using USB port and supplied USB cable (Mini-
Config configuration software application available via download from AJA
website)
• Uses universal input +5V power supply AJA model DWP-U-R1 (included)
12G-AMA v1.0 6 www.aja.com
12G-AMA Simplified Block Diagram
EQ Cable Driver
Embed and Pass-through
Packet Processor
Analog Input 1
(Ch 1)
XLR Breakout Cable
XLR Breakout Cable
12G-SDI Out
12G-SDI In
Analog Input 2
(Ch 2)
Analog Input 3
(Ch 3)
Analog Input 4
(Ch 4)
Analog Output 1
(Ch 1)
Analog Output 2
(Ch 2)
Analog Output 3
(Ch 3)
Analog Output 4
(Ch 4)
Dis-
Embedder
DAC
DAC
DAC
DAC
ADC
USB Port
(connect to
PC or Mac)
Mini-Cong
Control
ADC
ADC
ADC
Optional SFP
Input with
Embedded Audio
SDI
RCVR
Optional SFP
Output
DIP Switch
User Interface
12G-AMA Simplied Block Diagram
12G-AMA I/O Connections
DC Power
Input
12G SDI
Output BNC
Analog I/O
D-Connector
(attaches to supplied
4 Input, 4 Output
Break-Out Cable with
XLR Balanced
Connectors)
USB Port
Lock LED
12G SDI
Input BNC
Lock LED
Optional
SFP
NOTE: The LOCK LED indicates valid input video by color. Off is no signal, green is SD
video, red is HD video, amber is 3G video, purple is 6G video, and blue is 12G
video.
12G-AMA v1.0 7 www.aja.com
User Controls
DIP Switches
The 12G-AMA has an 8 position DIP switch accessible through a cut-out in the
bottom of the unit. The DIP switches are used to configure the unit’s audio
embedding and disembedding, and control ancillary data.
Figure 1. 12G-AMA DIP Switches and Label
1 2 3 4 5 6 7 8
DIP Switch Setting
LEFT RIGHT
LOCAL
ON
ON
0
0
0
0
ON
CONTROL
EMBD 1/2
EMBD 3/4
EMBD GRP L
EMBD GRP H
DISEMBD GRP L
DISEMBD GRP H
PASS HANC
REMOTE
OFF
OFF
1
1
1
1
OFF
Factory default switch settings are all in the leftmost position.
The exact functions of the DIP switches are described in "DIP Switch Settings" on
page 10
Mini-Config Control
The Mini-Config application can also be used to configure the unit’s audio
embedding and disembedding functions. Configuration set via Mini-Config is
stored in the unit through subsequent power cycles.
Installing and using Mini-Config are described in "USB Control and Setup—Using
AJA Mini-Config" on page 12
NOTE: DIP switch 1 must be ON (Remote, Right) to permit Mini-Config control of the unit.
Installation
NOTE: AJA does not support third-party SFP modules. Use of a non-AJA SFP module will
void the warranty.
12G-AMA-T ships with a 12G-SDI Fiber LC single channel SFP transmitter.
12G-AMA-R ships with a 12G-SDI Fiber LC single channel SFP receiver.
12G-AMA-TR ships with a 12G-SDI Fiber LC channel SFP transceiver.
12G-AMA-T-ST ships with a 12G-SDI Fiber ST single channel SFP transmitter.
12G-AMA-R-ST ships with a 12G-SDI Fiber ST single channel SFP receiver.
Typically, 12G-AMA installation consists of the following steps:
1. Ensure the converter is disconnected from power.
2. Connect video equipment to the converter BNCs.
3. If applicable, connect ber to the 12G-SDI Fiber LC or ST single channel SFP
receiver, transmitter or transceiver.
12G-AMA v1.0 9 www.aja.com
Breakout Cable Pinouts
Figure 3. AES Breakout Cable Illustration, XLR Connectors
pin 13
End Vi
ew ewSide Vi
pi 1n
pin
14
pin
25
pi 1 pi 2n n
pi 3n
Inpu At
Inpu Bt
Inpu Ct
Inpu Dt
Outp Aut
Outp But
Outp Cut
Outp Dut
Channel Index
Inpu At
Inpu Bt
Inpu Ct
Inpu Dt
Outpu At
Outpu Bt
Output C
Output D
= Analog In Ch. 1
= Analog In Ch. 2
= Analog In Ch. 3
= Analog In Ch. 4
= Analog Out Ch. 1
= Analog Out Ch. 2
= Analog Out Ch. 3
= Analog Our Ch. 4
pin 2 pin 1
pin
3
Table 1. XLR DB25 Breakout Cable Pinouts
Pin Function Pin, <connector> Function Pin, <connector>Pin
1 In 4 + 2, XLR Input D In 4 - 3, XLR Input D14
2 In 4 GND 1, XLR Input D In 3 + 2, XLR Input C15
3 In 3 - 3, XLR Input C In 3 GND 1, XLR Input C16
4 2, XLR Input B In 2 - 3, XLR Input BIn 2+ 17
5 In 2 GND 1, XLR Input B In 1 + 2, XLR Input A18
6 In 1 - 3, XLR Input A In 1 GND 1, XLR Input A19
7 Out 4 + 2, XLR Output D Out 4 - 3, XLR Output D20
8 Out 4 GND 1, XLR Output D Out 3 + 2, XLR Output C21
9 Out 3 - 3, XLR Output C Out 3 GND 1, XLR Output C22
10 Out 2 + 2, XLR Output B Out 2 - 3, XLR Output B23
11 Out 2 GND 1, XLR Output B Out 1 + 2, XLR Output A24
12 Out 1 - 3, XLR Output A Out 1 GND 1, XLR Output A25
13 NC NC
12G-AMA v1.0 10 www.aja.com
Chapter 2 – Operation
Default Operational Settings
The 12G-AMA converter ships from the factory with the following configuration:
• Local (DIP switch) control.
• Input analog audio channels 1-4 are embedded to SDI output channels 1-4,
overwriting any existing embedded audio.
• Input SDI embedded audio channels 1-4 are disembedded to analog audio
output channels 1-4.
• All HANC packets pass from SDI input to output, except for embedded output
audio channels 1-4.
• Analog audio operating level is set to 0 dBfs = +24 dBu (Pro 1).
If these settings apply to your requirements, you can simply connect the video
and audio input and output signal cables and power up the unit.
For other applications, you can configure the unit using its DIP switch settings, or
by using the Mini-Config application and a PC or Mac via USB. Analog audio levels
as well as video input source and stream selection can only be set using Mini-
Config.
DIP Switches
The 12G-AMA DIP switches configure the audio embedding and disembedding
functions, and control ancillary data.
DIP Switch Settings
DIP switch settings used to configure various functions are described below.
Table 2. 12G-AMA DIP Switch Setting Descriptions
SWITCH FUNCTION DIP Set LEFT (default) DIP Set RIGHT
1 Selects Local (DIP), and Control
blocks Mini-Config control.
Selects Remote (Mini-Config),
and disables DIP switches 2-8.
2 Audio Embedding for
Channels 1/2 (EMBD 1/2)
(ON) Overwrite or embed
new channel 1/2 packets.
(OFF) If SW 8 is set to ON: Pass
any channel 1/2 packets from
input SDI.
If SW 8 is set to OFF: Delete all
packets from input SDI.
3 Audio Embedding for
Channels 3/4 (EMDB 3/4)
(ON) Overwrite or embed
new channel 3/4 packets.
(OFF) If SW 8 is set to ON: Pass
any channel 3/4 packets from
input SDI.
If SW 8 is set to OFF: Delete all
packets from input SDI.
4 Channel Mapping For
Low Embedded Groups
(EMBD GRP L)
Switches 4 and 5 operate together to determine Embedded
channel mapping.
0 represents a Left DIP switch position
1 represents a Right DIP switch position
Refer to "Embedded Output Channel Mapping" on page 11 for
specific settings.
5 Channel Mapping For
High Embedded Groups
(EMBD GRP H)
12G-AMA v1.0 11 www.aja.com
6 Channel Mapping For
Low Disembedding
Groups (DISEMBD GRP L)
Switches 6 and 7 operate together to determine Disembedded
channel mapping.
0 represents a Left DIP switch position
1 represents a Right DIP switch position
Refer to
"Disembedded Input Channel Mapping" on page 12
for specific settings.
7 Channel Mapping For
High Disembedding
Groups (DISEMBD GRP H)
8 Pass or Drop HANC input
packets. (PASS HANC)
(ON) All incoming HANC
packets are passed unless
the embedder settings
above require all or part of
them to be over-written.
(OFF) All incoming HANC
packets are dropped before
embedding any new audio
packets. Embedder settings
above determine all embedded
audio output. Disembedding is
not affected.
NOTE: 2048x1080p/psf 29.97 and 30 formats support a maximum of 8 channels of
embedded audio. When one of these formats is present and embedding is turned
on, the PASS HANC DIP switch will be ignored and all incoming packets will be
dropped before embedding any new audio packets.
Switches 4 and 5 Channel Mapping For Embedded Groups
The following table shows how combinations of setting these two switches
affects embedded channel mapping.
Table 3. Embedded Output Channel Mapping
DIP SW 4
EMBD GRP L
DIP SW 5
EMBD GRP H
Audio Input
Channel
SDI Embedded
Group
SDI Embedded
Output Channel
Left (0) Left (0) 1 —> 1 1
2 —> 2
3 —> 3
4 —> 4
Right (1) 2 5Left (0) 1 —>
2 —> 6
3 —> 7
4 —> 8
Left (0) Right (1) 3 91 —>
2 —> 10
3 —> 11
4 —> 12
Right (1) Right (1) 41 —> 13
2 —> 14
3 —> 15
4 —> 16
12G-AMA v1.0 12 www.aja.com
Switches 6 and 7 Channel Mapping For Disembedded
Groups
The following table shows how combinations of setting these two switches
affects disembedding channel mapping.
Table 4. Disembedded Input Channel Mapping
DIP SW 6
DISEMBD GRP L
DIP SW 7
DISEMBD GRP H
SDI Embedded
Input Group
SDI Embedded
Input Channel
Audio Output
Channel
Left (0) Left (0) 1 11 —>
2 —> 2
3 —> 3
4 —> 4
Right (1) 2 1Left (0) 5 —>
6 —> 2
7 —> 3
8 —> 4
Left (0) Right (1) 3 19 —>
10 —> 2
11 —> 3
12 —> 4
Right (1) Right (1) 4 113 —>
14 —> 2
15 —> 3
16 —> 4
USB Control and Setup—Using AJA Mini-Config
Your AJA Mini-Converter can be used right out of the box for some applications
since it is designed to recognize inputs and perform standard actions
automatically by default. However, to use its full capability, you must use AJA’s
Mini-Config software application for PCs and Macs. This same application can be
used to update to new Mini-Converter software released by AJA.
NOTE: DIP switch 1 must be ON (Remote, Right) to permit Mini-Config control of the
unit. If DIP switch 1 is set to OFF (Local, Left), Mini-Config will report status, but its
control functions will be locked out.
Acquiring Mini-Config
AJA’s Mini-Config application is available for download from the AJA website.
To download the latest Mini-Config package, which includes the Mini-Config
application, Mini-Converter firmware, and documentation, go to:
https://www.aja.com/products/mini-config-software
Select either the Windows or Mac icon to download the desired version.
12G-AMA v1.0 13 www.aja.com
Mini-Converter Documentation
Included with the Mini-Config package is a complete set of documentation for
all Mini-Converters supported by Mini-Config. A .PDF of the Installation and
Operation Guide for the currently connected Mini-Converter can be accessed from
the Mini-Config UI via the Help/Manual drop-down menu.
Documentation for all AJA Mini-Converters that use Mini-Config can also be
accessed directly in the Mini-Config download package Documentation folder,
and via the Documentation icon available on the Mac installer.
Documentation (and firmware) included with the Mini-Config application are the
versions available at the time of distribution. However, Mini-Converter software,
firmware and documentation are updated regularly, so newer versions may exist.
To download the latest documentation for an individual Mini-Converter, go to:
https://www.aja.com/family/mini-converters
and navigate to the Support web page of that Mini-Converter.
Installing Mini-Config
PC Installation
To install Mini-Config on a Windows PC:
1. Download the application from the AJA website (select the Windows icon
on the Mini-Config Support web page).
2. Open the AJA_MiniCong.zip le
3. Double-click on the MiniInstaller.msi le.
4. A Setup Wizard will guide you through the installation.
Figure 4. Mini-Config PC Setup Wizard
5. Click Next to begin. Answer the questions in the subsequent dialogs. When
nished, an AJA Mini-Cong shortcut will be installed on the desktop, and
you will be able to locate the Mini-Cong application in the AJA folder in
the Programs listing.
NOTE: If the Mini-Config application already exists on the PC, a different Setup Wizard
appears.
12G-AMA v1.0 14 www.aja.com
Figure 5. Mini-Config Setup Wizard, Reinstallation
With this screen you can Repair (reinstall) or (uninstall) Mini-Config on Remove
the PC.
Mac Installation
To install the application on a Mac:
NOTE: Mac computers must be Intel-based (G5, G4 and earlier models will not work
with Mini-Config).
1. Download the application from the AJA website (select the Apple icon on
the Mini-Config Support web page).
2. Open the AJA_MiniCong folder.
3. Double-click on the AJAMiniCong.dmg le.
4. Answer the prompt and a utility program will be launched.
Figure 6. Mini-Config Mac Installer
5. To complete the installation drag the icon to the MiniCong.app
Applications folder.
Running Mini-Config
Connect the Mini-Converter to the PC or Mac via the supplied USB cable. Connect
the external power supply (supplied) to the Mini-Converter.
12G-AMA v1.0 15 www.aja.com
PC Startup
To run Mini-Config on a PC, double-click on the AJA Mini-Config icon on your
desktop, or open the AJA folder in the program list and click on the AJA Mini-
Config application located inside the Mini-Config folder.
Mac Startup
To run Mini-Config on a Mac, open the Applications folder and locate the AJA
Mini-Config application. Double-click the application to launch it.
Saving Setups
A drop down menu on the Mini-Config application bar allows you to save the
File
current state of the Mini-Converter to a preset file for later recall.
Using this feature you can set up the converter for different applications, storing
each configuration ( ) with a unique name for easy recall (Save Preset As... Open
Preset...).
A Revert to Factory Settings menu item similarly allows you to change the
settings back to AJA’s factory defaults.
Operating Mini-Config
The Mini-Config application provides a graphic interface for viewing settings
and updating software. It consists of an information area at the top that shows
the available Mini-Converters attached to the computer via USB, with a graphical
rendering of the selected Mini-Converter showing all the connectors and their
current state.
Colored text next to the connectors indicates the signal type and what the Mini-
Converter is doing:
• Blue text indicates the values automatically selected
• Black text indicates values that you have manually selected
• Red text indicates the Mini-Converter is not detecting a signal, or cannot
operate with the current user settings.
NOTE: Even if no output device is detected, the SDI connector text still shows the signal it
is outputting.
12G-AMA v1.0 16 www.aja.com
NOTE: Configuration settings in red will change based on the attached output device as
well as input signals. For improved accuracy and reliability, you should configure
the Mini-Converter only when the target output device is attached and input
signals are supplied at the inputs.
Screens are virtually the same on both PC and Mac, with subtle differences that
reflect the general look of the platform environment.
Figure 7. Example Mini-Config Screen
Select a USB port and
an attached
Mini-Converter (name
in parentheses).
Each connector is
labeled with the
signals currently
detected or manually
selected.
Firmware Version
and Serial Number
Status Message
Tabbed Screens
Selecting a Mini-Converter with the pulldown menu causes this application to
connect to the selected converter. The graphic of Mini-Converter and text below
it provides:
• Type of converter
• Firmware version
• Serial number of the unit
A status field at the bottom of the screen shows if your application is connected
and communicating with the Mini-Converter.
When configuring the Mini-Converter, select it from the top pulldown, view the
current settings and change any values. Making a change communicates that
new value to the Mini-Converter’s non-volatile memory.
Tabbed Screens
The Tabs delineate control screens with groups of controls for each type of task to
be performed.
The controls for the actual configuration parameters are specific to each Mini-
Converter type. When you click on any of the tab buttons, the pane below
the tabs will change to match your tab selection. Any changes you make are
immediately applied and will be saved, overwriting previous settings.
12G-AMA v1.0 17 www.aja.com
Input Tab Screen
Click on the Input tab to view and make changes to the Input settings.
Input Select
Select the active video source:
• BNC
• SFP
3G-SDI Level B
For 3G Level B signals, selects either the 16 audio channels of input Stream A or
the 16 channels of input Stream B for disembedding. This setting also controls
whether output Stream A or output Stream B will receive embedded audio. This
control is active whenever a 3G-SDI Level B-DL or B-DS input signal is detected.
12G-AMA v1.0 18 www.aja.com
Audio-1 Tab Screen
Click on the Audio-1 tab to view and make changes to the audio embedding and
disembedding settings.
Analog Audio Inputs
Embed to:
Select the audio group to which you want to embed the incoming analog audio:
• Group 1 (Ch 1-4)
• Group 2 (Ch 5-8)
• Group 3 (Ch 9-12)
• Group 4 (Ch 13-16)
Ch 1/2 Embed:
• Selecting On embeds the analog audio Ch 1/2 pair in the first two channels of
the group selected above.
Ch 3/4 Embed:
• Selecting On embeds the analog audio Ch 3/4 pair in the last two channels of
the group selected above.
12G-AMA v1.0 19 www.aja.com
Analog Audio Outputs
Disembed from:
Choose which SDI embedded audio group will disembed its audio and send it to
the four analog audio outputs:
• Group 1 (Ch 1-4)
• Group 2 (Ch 5-8)
• Group 3 (Ch 9-12)
• Group 4 (Ch 13-16)
Audio-2 Tab Screen
Click on the Audio-2 tab to view and make changes to the packet processing and
audio level settings.
Packet Processing Control
HANC Data:
• Pass – All incoming HANC packets are passed unless the embedder settings
require all or part of them to be over-written.
• Remove – All incoming HANC packets are dropped before embedding any
new audio packets. The embedder settings determine all embedded audio
output. Disembedding is not affected.
NOTE: 2048x1080p/psf 29.97 and 30 formats support a maximum of 8 channels of
embedded audio. When one of these formats is present and embedding is turned
on, the PASS HANC setting will be ignored and all incoming packets will be
dropped before embedding any new audio packets.
12G-AMA v1.0 20 www.aja.com
Analog Audio Levels
• Select from Full Scale Digital settings of +24, +18, +15 (professional), or +12dBu
(consumer).
About Audio Levels
Professional audio equipment has much higher levels than consumer equipment:
a 0 VU reading corresponds to +4 dBu. Connecting a professional +4 dBu device
to a consumer audio input (-7 to -8 dBu) may produce overloading, whereas the
output of a consumer device probably does not have sufficient power to drive a
professional audio input. With consumer and semi-professional audio equipment,
a VU reading of 0 dB is typically referenced to -10 dBV, which is equivalent to -7.78
dBu.
Update Tab Screen
Use this Update tab screen to view the software version currently installed on the
converter or install new software.
NOTE: When discussing Mini-Converters, “Firmware” is software that will be stored in
the Mini-Converter’s non-volatile memory and used when it is powered up. This
is something different than the Mini-Config application software. The version
numbers shown in the Update screen refer only to the firmware.
Installed
This field shows the version of the firmware currently installed inside the Mini-
Converter.
Desired
This field shows the version of firmware embedded in the Mini-Config application
which you can install into the Mini-Converter by clicking the Update button.
12G-AMA v1.0 21 www.aja.com
Update
This button initiates a software update operation loading the “Desired” version of
firmware into the Mini-Converter’s non-volatile memory.
Progress
This indicator bar shows the progress of firmware installation.
See "Acquiring Mini-Config" on page "Installing Mini-Config" on page 12 and 13
for more information.
Info Tab Screen
This screen provides basic information about the Mini-Converter. This information
is mostly useful when calling AJA Support for service or technical support.
Name
This field allows you to give your Mini-Converter a name. This can be useful if you
have several Mini-Converters attached to a Mac/PC via USB so you can distinguish
between them easily (especially if they’re the same model).
Type
This is the factory set model name of the Mini-Converter.
Assembly
This is the factory assembly number.
Serial Number
This is the factory set unique serial number of your Mini-Converter. If you ever call
AJA Support for service, you may be asked for this number.
12G-AMA v1.0 22 www.aja.com
Appendix A – Specifications
12G-AMA Family Tech Specs
Video Formats
• (4K) 4096x2160p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• (UltraHD) 3840x2160p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• (2K) 2048x1080p 50, 59.94, 60
• (HD) 1920x1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• (HD) 1920x1080i 50, 59.94, 60
• (HD) 1280x720p 50, 59.94, 60*
• (SD) 625i 50
• (SD) 525i 59.94
• RGB and YCbCr, 4:4:4/4:2:2, 10-bit
*1280x720p is Level A Only
NOTE: Raster and frame rate dependent, please see 12G-AMA Video Formats in
Documents and Manual.
Video Input Digital
• 1x 12G-SDI BNC, SMPTE 259/292/424/2081/2082
• Single Link SD/HD/2K/UltraHD/4K
• Single Link 3G-SDI Level A, B-DL, or B-DS, SMPTE 425
Video Input Digital - Additional for 12G-AMA-R and 12G-AMA-TR Only
• 1x 12G-SDI Fiber LC connector, SMPTE 297/259/292/424/2081/2082
• Wavelength: Rx 1260 nm (min), 1620 nm (max)
• Optical Sensitivity: -10 dBm (min 12 Gbps), -14 dBm (min 3 Gbps)
• Overload Power: -2 dBm (min)
Video Input Digital - Additional for 12G-AMA-R-ST Only
• 1x 12G-SDI Fiber ST connector, SMPTE 297/259/292/424/2081/2082
• Wavelength: Rx 1260 nm (min), 1620 nm (max)
• Optical Sensitivity: -10 dBm (min 12 Gbps), -14 dBm (min 3 Gbps)
• Overload Power: -2 dBm (min)
Video Output Digital
• 1x 12G-SDI BNC, SMPTE 259/292/424/2081/2082
• Single Link SD/HD/2K/UltraHD/4K
• Single Link 3G-SDI Level A, B-DL, or B-DS, SMPTE 425
Video Output Digital - Additional for 12G-AMA-T, and 12G-AMA-TR Only
• 1x 12G-SDI Fiber LC connector, SMPTE 297/259/292/424/2081/2082
• Nominal Wavelength: Tx 1260 nm (min), 1310 nm (typ), 1360 nm (max)
• Optical Power: -5 dBm (min), 0.5 dBm (max)
• Extinction Ratio: 5.4 dB (min)
Video Output Digital - Additional for 12G-AMA-T-ST Only
• 1x 12G-SDI Fiber ST connector, SMPTE 297/259/292/424/2081/2082
• Nominal Wavelength: Tx 1260 nm (min), 1310 nm (typ), 1360 nm (max)
12G-AMA v1.0 23 www.aja.com
• Optical Power: -5 dBm (min), 2 dBm (max)
• Extinction Ratio: 3.4 dB (min)
Cable Equalization
(Belden 1694A coax)
• 12 Gbps, 65m
• 6 Gbps, 125m
• 3 Gbps, 190m
• 1.5 Gbps, 200m
• 270 Mbps, 405m
Audio Inputs and Outputs
• Balanced Analog Audio, 1x 25 pin D female connector on the converter,
4-channels in, 4-channels out
• Breakout cable provided with 1x 25 pin D male connector:
• 4x XLR female input breakout connectors
• 4x XLR male output breakout connectors
Digital Audio Converters
• 24-bit
Embedded Audio
• SMPTE 272M (SD): 20-bit, 48 kHz synchronous
• SMPTE 299M (12G/6G/3G/1.5G): 24-bit, 48 kHz synchronous
• Incoming embedded audio can be passed, removed, or overridden
• Up to 16 channels supported
NOTE: 2048x1080p/PsF 29.97 and 30 formats support a maximum of 8-channels
embedded audio.
Audio Latency
• Embed Path 1100 µsec
• Disembed Path 1200 µsec
Analog Audio Levels
Configured via Mini-Config software:
• Pro 1: 0 dBfs = +24 dBu
• Pro 2: 0 dBfs = +18 dBu
• Pro 3: 0 dBfs = +15 dBu
• Consumer 1: 0 dBfs = +12 dBu
User Interface
• External DIP switch
• USB port used with Mini-Config software application to configure the device
via PC/Mac
Size (w x d x h)
• 5.8" x 3.1" x 1.0" (147.32 x 78.74 x 25.4 mm)
Weight
• 0.6 lb (0.3 kg)
Power
• +5-16VDC, 10 watts. power supply required, included with purchase
12G-AMA v1.0 24 www.aja.com
Environment
• Safe Operating Temperature: 0 to 40 C (32 to 104 F)
• Safe Storage Temperature (Power OFF): -40 to 60 C (-40 to 140 F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
12G-AMA v1.0 25 www.aja.com
12G-AMA Video I/O Formats
4K/UltraHD Inputs Supported
1x 12Gb SDI:
Format Frame Rate Colorspace Sampling Bit Depth
• 3840x2160p 23.98, 24, 25, 29.97, 30 YCbCr/RGB 4:4:4 10
• 3840x2160p 50, 59.94, 60 YCbCr 4:2:2 10
• 4096x2160p 23.98, 24, 25, 29.97, 30 YCbCr/RGB 4:4:4 10
• 4096x2160p 50, 59.94, 60 YCbCr 4:2:2 10
1x 6Gb SDI:
Format Frame Rate Colorspace Sampling Bit Depth
• 3840x2160p 23.98, 24, 25, 29.97, 30 YCbCr 4:2:2 10
• 4096x2160p 23.98, 24, 25, 29.97, 30 YCbCr 4:2:2 10
2K/HD Inputs Supported
1x 3Gb SDI:
Format Frame Rate
Level A/B Colorspace Sampling Bit Depth
• 1280x720p 50, 59.94, 60 A YCbCr/RGB 4:4:4 10
• 1920x1080i 50, 59.94, 60 A or B-DL YCbCr/RGB 4:4:4 10
• 1920x1080p 23.98, 24, 25, 29.97, 30 A or B-DL YCbCr/RGB 4:4:4 10
• 1920x1080p 50, 59.94, 60 A or B-DL YCbCr 4:2:2 10
• 1920x1080PsF 23.98, 24, 25, 29.97, 30 A or B-DL YCbCr/RGB 4:4:4 10
• 2048x1080p 23.98, 24, 25, 29.97, 30 A or B-DL YCbCr/RGB 4:4:4 10
• 2048x1080p 50, 59.94, 60 A or B-DL YCbCr 4:2:2 10
• 2048x1080PsF 23.98, 24, 25, 29.97, 30 A or B-DL YCbCr/RGB 4:4:4 10
1x 1.5Gb SDI:
Format Frame Rate Colorspace Sampling Bit Depth
• 1280x720p 50, 59.94, 60 YCbCr 4:2:2 10
• 1920x1080i 50, 59.94, 60 YCbCr 4:2:2 10
• 1920x1080p 23.98, 24, 25, 29.97, 30 YCbCr 4:2:2 10
• 1920x1080PsF 23.98, 24, 25, 29.97, 30 YCbCr 4:2:2 10
12G-AMA v1.0 26 www.aja.com
• 2048x1080p 23.98, 24, 25, 29.97, 30 YCbCr 4:2:2 10
• 2048x1080PsF 23.98, 24, 25, 29.97, 30 YCbCr 4:2:2 10
SD Inputs Supported
1x 270Mb SDI
Format Frame Rate Colorspace Sampling Bit Depth
• 525i 59.94 YCbCr 4:2:2 10
• 625i 50 YCbCr 4:2:2 10
12G-AMA v1.0 27 www.aja.com
Appendix B – Safety and Compliance
Federal Communications Commission (FCC) Compliance Notices
Class A Interference Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15, Subpart B of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Canadian ICES Statement
Canadian Department of Communications Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio-noise emissions
from a digital apparatus as set out in the Radio Interference Regulations of
the Canadian Department of Communications. This Class A digital apparatus
complies with Canadian ICES-003.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique respecte les limites de bruits radioélectriques visant les
appareils numériques de classe A prescrites dans le Règlement sur le brouillage
radioélectrique du ministère des Communications du Canada. Cet appareil
numérique de la Classe A est conforme à la norme NMB-003 du Canada.
European Union and European Free Trade Association (EFTA)
Regulatory Compliance
This equipment may be operated in the countries that comprise the member
countries of the European Union and the European Free Trade Association. These
countries, listed in the following paragraph, are referred to as The European
Community throughout this document:
AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA,
FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA,
LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL,
ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, ICELAND,
LICHTENSTEIN, NORWAY, SWITZERLAND
12G-AMA v1.0 28 www.aja.com
Declaration of Conformity
Marking by this symbol indicates compliance with the Essential Requirements of
the EMC Directive of the European Union 2014/30/EU.
This equipment meets the following conformance standards:
Safety
EN 60065: 2014 (T-Mark License)
IEC 60065: 2014 (CB Scheme Report/Certificate)
EN 62368-1: 2014 + A11 (T-Mark License)
IEC 62368-1: 2014 (CB Scheme Certificate)
Additional licenses issued for specific countries available on request.
Emissions
EN 55032: 2012 + AC: 2013, CISPR 32: 2015,
EN 61000-3-2: 2014, EN 61000-3-3: 2013
Immunity
EN 55103-2: 2009
EN 61000-4-2:2009, EN 61000-4-3:2006 +A1:2008 +A2:2010,
EN 61000-4-4:2004 +A1:2010, EN 61000-4-5:2006, EN 61000-4-6: 2009
EN 61000-4-11:2004
Environments: E2, E3 and E4
Laser
EN 60825-1: 2007 and EN 60825-2: 2004 +A2: 2010,
CDRH Compliant Class 1 (TUV Cert No. 50135086)
Also Licensed for Standards: FDA 21 CFR 1040.10 and 1040.11
The product is also licensed for additional country specific standards as required
for the International Marketplace.
Warning! This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case, the user may be required to take
appropriate measures.
Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen
können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in welchen
Fällen der Benutzer für entsprechende Gegenmaßnahmen verantwortlich ist.
Attention! Ceci est un produit de Classe A. Dans un environnement domestique,
ce produit risque de créer des interférences radioélectriques, il appartiendra
alors à l?utilisateur de prendre les mesures spécifiques appropriées..
Recycling Notice
This symbol on the product or its packaging indicates that this product
must not be disposed of with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment
at the time of disposal will help conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste for recycling,
please contact your local authority, or where you purchased your product.
12G-AMA v1.0 29 www.aja.com
Korea KCC Compliance Statement
ꩡ끞녅껽驩ꓭ
넩 韥韥鱉 꽺ꓩ끞 쀍陲꾅 ꩡ끞뼕 놶뼞ꫦ뵾閵ꌱ ꗐ냵 韥韥ꈑ ꑞ놶냱ꈑ 閵뇊
끞 쀍陲꾅 ꩡ끞뼍鱉 陲끥 놹볁閹ꫢ넍 끥ꇙ閵 넽걪鱽鲙.
Taiwan Compliance Statement
This is a Class A product based on the standard of the Bureau of Standards,
Metrology and Inspection (BSMI) CNS 13438, Class A. In a domestic environment
this product may cause radio interference in which case the user may be required
to take adequate measures.
Japan Compliance Statement
This is a Class A product based on the standard of the VCCI Council (VCCI-32:
2016). If this equipment is used in a domestic environment, radio interference
may occur, in which case, the user may be required to take corrective actions.
Translated Warning and Caution Messages
The following caution statements, warning conventions, and warning messages
apply to this product and manual.
12G-AMA v1.0 30 www.aja.com
Before Operation Please Read These Instructions
Warning! Read and follow all warning notices and instructions marked on the
product or included in the documentation.
Avertissement! Lisez et conformez-vous à tous les avis et instructions
d'avertissement indiqués sur le produit ou dans la documentation.
Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf
dem Produkt angebracht oder in der Dokumentation enthalten sind.
¡Advertencia! Lea y siga todas las instrucciones y advertencias marcadas en el
producto o incluidas en la documentación.
Aviso! Leia e siga todos os avisos e instruções assinalados no produto ou incluídos
na documentação.
Avviso! Leggere e seguire tutti gli avvisi e le istruzioni presenti sul prodotto o
inclusi nella documentazione.
Warning! Do not use this device near water and clean only with a dry cloth.
Avertissement! N'utilisez pas cet appareil près de l'eau et nettoyez-le seulement
avec un tissu sec.
Warnung! Das Gerät nicht in der Nähe von Wasser verwenden und nur mit einem
trockenen Tuch säubern.
¡Advertencia! No utilice este dispositivo cerca del agua y límpielo solamente con
un paño seco.
Aviso! Não utilize este dispositivo perto da água e limpe-o somente com um pano
seco.
Avviso! Non utilizzare questo dispositivo vicino all'acqua e pulirlo soltanto con un
panno asciutto.
Warning! Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Avertissement! Ne bloquez aucune ouverture de ventilation. Suivez les
instructions du fabricant lors de l'installation.
Warnung! Die Lüftungsöffnungen dürfen nicht blockiert werden. Nur gemäß den
Anweisungen des Herstellers installieren.
¡Advertencia! No bloquee ninguna de las aberturas de la ventilación. Instale de
acuerdo con las instrucciones del fabricante.
Aviso! Não obstrua nenhuma das aberturas de ventilação. Instale de acordo com as
instruções do fabricante.
Avviso! Non ostruire le aperture di ventilazione. Installare in conformità con le
istruzioni del fornitore.
Warning! Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Avertissement! N'installez pas l'appareil près d'une source de chaleur telle que des
radiateurs, des bouches d'air de chauffage, des fourneaux ou d'autres appareils
(amplificateurs compris) qui produisent de la chaleur.
Warnung! Nicht in der Nähe von Wärmequellen wie Heizkörpern, Heizregistern,
Öfen oder anderen Wärme erzeugenden Geräten (einschließlich Verstärkern)
aufstellen.
¡Advertencia! No instale cerca de fuentes de calor tales como radiadores, registros
de calor, estufas u otros aparatos (incluidos amplificadores) que generan calor.
Aviso! Não instale perto de nenhuma fonte de calor tal como radiadores, saídas
de calor, fogões ou outros aparelhos (incluindo amplificadores) que produzam
calor.
Avviso! Non installare vicino a fonti di calore come termosifoni, diffusori di aria
calda, stufe o altri apparecchi (amplificatori compresi) che emettono calore
12G-AMA v1.0 31 www.aja.com
Warning! Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
Avertissement! La sécurité de la prise polarisée ou de la prise de type mise à la
terre ne doit en aucun cas être empêchée de fonctionner. Une prise polarisée
a deux broches, l'une étant plus large que l'autre. Une prise de type mise à la
terre a deux broches et une troisième broche pour la mise à la terre. La broche
large ou la troisième broche sont fournies pour votre sécurité. Si la prise
fournie ne s'insère pas dans votre prise femelle, consultez un électricien pour le
remplacement de la prise femelle obsolète.
Warnung! Der Sicherheitszweck des gepolten bzw. Schukosteckers ist zu
berücksichtigen. Ein gepolter Stecker verfügt über zwei Pole, von denen einer
breiter als der andere ist. Ein Schukostecker verfügt neben den zwei Polen noch
über einen dritten Pol zur Erdung. Der breite Pol bzw. der Erdungspol dienen der
Sicherheit. Wenn der zur Verfügung gestellte Stecker nicht in Ihren Anschluss
passt, konsultieren Sie einen Elektriker, um den veralteten Anschluss zu ersetzen.
¡Advertencia! No eche por tierra la finalidad del tipo de enchufe polarizado con
conexión a tierra. Un enchufe polarizado tiene dos espigas, una más ancha
que la otra. Un enchufe con conexión a tierra tiene dos espigas iguales y una
tercera espiga que sirve para la conexión a tierra. La expiga ancha, o la tercera
espiga, sirven para su seguridad. Si el enchufe suministrado no encaja en el
tomacorriente, consulte con un electricista para reemplazar el tomacorriente
obsoleto.
Aviso! Não anule a finalidade da segurança da ficha polarizada ou do tipo ligação
terra. Uma ficha polarizada tem duas lâminas sendo uma mais larga do que
a outra. Uma ficha do tipo de ligação à terra tem duas lâminas e um terceiro
terminal de ligação à terra. A lâmina larga ou o terceiro terminal são fornecidos
para sua segurança. Se a ficha fornecida não couber na sua tomada, consulte um
electricista para a substituição da tomada obsoleta.
Avviso! Non compromettere la sicurezza della spina polarizzata o con messa a
terra. Una spina polarizzata ha due spinotti, di cui uno più largo. Una spina con
messa a terra ha due spinotti e un terzo polo per la messa a terra. Lo spinotto
largo o il terzo polo sono forniti per motivi di sicurezza. Se la spina fornita non
si inserisce nella presa di corrente, contattare un elettricista per la sostituzione
della presa obsoleta.
Warning! Since the Mains plug is used as the disconnection for the device, it must
remain readily accessible and operable.
Avertissement! Puisque la prise principale est utilisée pour débrancher l'appareil,
elle doit rester aisément accessible et fonctionnelle.
Warnung! Da der Netzstecker als Trennvorrichtung dient, muss er stets zugänglich
und funktionsfähig sein.
¡Advertencia! Puesto que el enchufe de la red eléctrica se utiliza como dispositivo
de desconexión, debe seguir siendo fácilmente accesible y operable.
Aviso! Dado que a ficha principal é utilizada como a desconexão para o dispositivo,
esta deve manter-se prontamente acessível e funcional.
Avviso! Poiché il cavo di alimentazione viene usato come dispositivo di
sconnessione, deve rimane prontamente accessibile e operabile.
12G-AMA v1.0 32 www.aja.com
Warning! Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the device.
Avertissement! Protégez le cordon d'alimentation pour que l'on ne marche
pas dessus ou qu'on le pince, en particulier au niveau des prises mâles, des
réceptacles de convenance, et à l'endroit où il sort de l'appareil.
Warnung! Vermeiden Sie, dass auf das Netzkabel getreten oder das Kabel geknickt
wird, insbesondere an den Steckern, den Steckdosen und am Kabelausgang am
Gerät.
¡Advertencia! Proteja el cable de energía para que no se le pise ni apriete, en
especial cerca del enchufe, los receptáculos de conveniencia y el punto del que
salen del equipo.
Aviso! Proteja o cabo de alimentação de ser pisado ou de ser comprimido
particularmente nas fichas, em tomadas de parede de conveniência e no ponto
de onde sai do dispositivo.
Avviso! Proteggere il cavo di alimentazione in modo che nessuno ci cammini sopra
e che non venga schiacciato soprattutto in corrispondenza delle spine e del
punto in cui esce dal dispositivo.
Warning! Unplug this device during lightning storms or when unused for long
periods of time.
Avertissement! Débranchez cet appareil pendant les orages avec éclairsou s'il est
inutilisé pendant de longues périodes.
Warnung! Das Gerät ist bei Gewitterstürmen oder wenn es über lange Zeiträume
ungenutzt bleibt vom Netz zu trennen.
¡Advertencia! Desenchufe este dispositivo durante tormentas eléctricas o cuando
no se lo utilice por largos periodos del tiempo.
Aviso! Desconecte este dispositivo da tomada durante trovoadas ou quando não é
utilizado durante longos períodos de tempo.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal
produttore, quali il treppiedi e l'esoscheletro.
12G-AMA v1.0 34 www.aja.com
Warning! Disconnect the external AC power supply line cord(s) from the mains
power before moving the unit.
Avertissement! Retirez le ou les cordons d’alimentation en CA de la source
d’alimentation principale lorsque vous déplacez l’appareil.
Warnung! Trennen Sie die Wechselstrom-Versorgungskabel vom Netzstrom, bevor
Sie das Gerät verschieben.
¡Advertencia! Cuando mueva la unidad desenchufe de la red eléctrica el/los
cable(s) de la fuente de alimentación CA tipo brick.
Advertência! Remova os cabos CA de alimentação brick da rede elétrica ao mover
a unidade.
Avvertenza! Scollegare il cavo dell’alimentatore quando si sposta l’unità.
Warning! Only use attachments and accessories specified and/or sold by the
manufacturer.
Avertissement! Utilisez seulement les attaches et accessoires spécifiés et/ou
vendus par le fabricant.
Warnung! Verwenden Sie nur Zusatzgeräte und Zubehör angegeben und / oder
verkauft wurde durch den Hersteller.
¡Advertencia! Utilice solamente los accesorios y conexiones especificados y/o
vendidos por el fabricante.
Aviso! Utilize apenas equipamentos/acessórios especificados e/ou vendidos pelo
fabricante.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal
produttore.
Caution! 12G-AMA devices require the use of “single mode 1310nm compatible”
fiber optic cable.
Aviso! Dispositivos 12G-AMA exigem a utilização de cabo de fibra ótica
"compatível com monomodo 1310nm ".
Attention! Les équipements 12G-AMA doivent être utilisés avec un câble en fibre
optique monomode compatible 1310 nm.
Attenzione I dispositivi 12G-AMA richiedono l'uso di un cavo a fibre ottiche
"compatibile con 1310 nm monomodo".
¡Precaución! 12G-AMA dispositivos requieren el uso de cable de fibra óptica
"mono modo 1310nm compatibles".
Vorsicht! 12G-AMA-Geräte erfordern den Gebrauch von "Einzelmodus 1310nm
kompatiblen" Faseroptik-Kabeln.
12G-AMA v1.0 35 www.aja.com
CLASS 1
LASER
PRODU CT
PRODUTO
LASER DE
CLASSE 1
PRODUITS
LASER DE
CLASSE 1
PRODOTTO
LASER DI
CLASSE 1
CLASE 1
LASER
PRODUCTO
KLASSE 1
LASER-
PRODUKT
Warning! Active fiber-optic cables emit radiation invisible to the human eye.
Do not look directly at the end of an active fiber-optic cable; the 12G-AMA is
a Class 1 Laser Product.
Advertência! Cabos de fibra ótica ativos emitem radiação invisível ao olho
humano. Não olhe diretamente para a extremidade de um cabo de fibra óptica
ativo; o 12G-AMA é um produto laser de classe 1.
Avertissement! Lorsqu'ils sont actifs, les câbles en fibre optique émettent
des radiations que l'oeil humain ne peut voir. Ne regardez pas directement
l'extrémité d'un câble en fibre optique en cours d'utilisation ; les équipements
12G-AMA sont des produits laser de classe 1.
Avvertenza I cavi a fibre ottiche attivi (ossia in cui si propagano segnali) emettono
radiazioni invisibili. Non fissare lo sguardo direttamente sull'estremità di un cavo
a fibre ottiche attivo; il cavo 12G-AMA è un prodotto laser di Classe 1.
¡Advertencia! Active los cables de fibra óptica de emitir radiación invisible para
el ojo humano. No mire directamente en el extremo de un cable de fibra óptica
activa; el 12G-AMA es un producto láser de Clase 1.
Achtung! Aktive Faseroptik-Kabel geben eine Strahlung ab, die für das
menschliche Auge unsichtbar ist. Das Ende eines aktiven Faseroptik-Kabels
niemals direkt ansehen; die 12G-AMA ist ein Laser-Produkt der Klasse 1.
12G-AMA v1.0 38 www.aja.com
Index
Symbols
3G-AMA I/O Connections 6
3G-AMA Simplified Block Diagram 6
A
AJA Support 2
Audio-1 Tab Screen 18
Audio-2 Tab Screen 19
B
Breakout Cable Pinouts 9
D
Default Operational Settings 10
DIP Switches 7
DIP Switch Settings 10
Documentation
Downloading 13
Mini-Converter 13
I
Info Tab Screen 21
Input Tab Screen 17
Installation 7
M
Mini-Config
Installation on Mac 14
Installation on PC 13
Operation 15
Screen Description 16
Startup on Mac 15
Startup on PC 15
Mini-Config Screen
Info Tab Screen 21
Update Tab Screen 20
Mini-Converter Documentation 13
O
Overview 4
S
Saving Setups 15
T
Technical Support 2
U
Update Tab Screen 20
X
XLR DB25 Breakout Cable 9
Produkt Specifikationer
Mærke: | AJA |
Kategori: | Audio/video konverter |
Model: | 12G-AMA |
Har du brug for hjælp?
Hvis du har brug for hjælp til AJA 12G-AMA stil et spørgsmål nedenfor, og andre brugere vil svare dig
Audio/video konverter AJA Manualer
15 Januar 2025
15 Januar 2025
15 Januar 2025
15 Januar 2025
15 Januar 2025
15 Januar 2025
22 September 2024
13 September 2024
24 August 2024
20 August 2024
Audio/video konverter Manualer
- Audio/video konverter Pro-Ject
- Audio/video konverter TP-Link
- Audio/video konverter Philips
- Audio/video konverter Pioneer
- Audio/video konverter Behringer
- Audio/video konverter D-Link
- Audio/video konverter Roland
- Audio/video konverter Pyle
- Audio/video konverter Yamaha
- Audio/video konverter Nedis
- Audio/video konverter Abus
- Audio/video konverter Planet
- Audio/video konverter Optoma
- Audio/video konverter Hama
- Audio/video konverter Rega
- Audio/video konverter Black Box
- Audio/video konverter DataVideo
- Audio/video konverter TRENDnet
- Audio/video konverter Vivanco
- Audio/video konverter Cambridge
- Audio/video konverter König
- Audio/video konverter Gembird
- Audio/video konverter Bose
- Audio/video konverter Tripp Lite
- Audio/video konverter Genie
- Audio/video konverter Digitus
- Audio/video konverter Techly
- Audio/video konverter EnerGenie
- Audio/video konverter Marmitek
- Audio/video konverter Thor
- Audio/video konverter Kathrein
- Audio/video konverter NAD
- Audio/video konverter Tascam
- Audio/video konverter LevelOne
- Audio/video konverter Zoom
- Audio/video konverter JUNG
- Audio/video konverter RME
- Audio/video konverter Focal
- Audio/video konverter Teac
- Audio/video konverter Tenda
- Audio/video konverter Vogel's
- Audio/video konverter Monacor
- Audio/video konverter JL Audio
- Audio/video konverter AVerMedia
- Audio/video konverter FiiO
- Audio/video konverter Renkforce
- Audio/video konverter Manhattan
- Audio/video konverter Eminent
- Audio/video konverter Kramer
- Audio/video konverter Metra
- Audio/video konverter Naim
- Audio/video konverter Mean Well
- Audio/video konverter VIZIO
- Audio/video konverter Evolution
- Audio/video konverter MuxLab
- Audio/video konverter Wavtech
- Audio/video konverter Iogear
- Audio/video konverter ATen
- Audio/video konverter Shure
- Audio/video konverter Power Dynamics
- Audio/video konverter Rockford Fosgate
- Audio/video konverter Aluratek
- Audio/video konverter Smart-AVI
- Audio/video konverter Scosche
- Audio/video konverter StarTech.com
- Audio/video konverter Rocstor
- Audio/video konverter GEM
- Audio/video konverter Adder
- Audio/video konverter Crestron
- Audio/video konverter Lindy
- Audio/video konverter Audison
- Audio/video konverter Audac
- Audio/video konverter FSR
- Audio/video konverter CYP
- Audio/video konverter Sitecom
- Audio/video konverter AMX
- Audio/video konverter Intellinet
- Audio/video konverter AudioControl
- Audio/video konverter Audiotec Fischer
- Audio/video konverter Silverstone
- Audio/video konverter Steren
- Audio/video konverter Ocean Matrix
- Audio/video konverter Comprehensive
- Audio/video konverter Intelix
- Audio/video konverter Digitalinx
- Audio/video konverter Audioengine
- Audio/video konverter Speaka
- Audio/video konverter Data-Tronix
- Audio/video konverter Key Digital
- Audio/video konverter KanexPro
- Audio/video konverter Gefen
- Audio/video konverter TV One
- Audio/video konverter Sescom
- Audio/video konverter Apantac
- Audio/video konverter RGBlink
- Audio/video konverter Blustream
- Audio/video konverter C2G
- Audio/video konverter WyreStorm
- Audio/video konverter Twelve South
- Audio/video konverter Ewent
- Audio/video konverter PAC
- Audio/video konverter Wentronic
- Audio/video konverter Luxman
- Audio/video konverter Monoprice
- Audio/video konverter SIIG
- Audio/video konverter Televés
- Audio/video konverter Micro Connect
- Audio/video konverter Extron
- Audio/video konverter PureLink
- Audio/video konverter Sunix
- Audio/video konverter Ebode
- Audio/video konverter INOGENI
- Audio/video konverter Antelope Audio
- Audio/video konverter CE Labs
- Audio/video konverter Epcom
- Audio/video konverter Karma
- Audio/video konverter SmartAVI
- Audio/video konverter Puls Dimension
- Audio/video konverter AVPro Edge
- Audio/video konverter Cudy
- Audio/video konverter Sabrent
- Audio/video konverter FoneStar
- Audio/video konverter Atlona
- Audio/video konverter HELGI
- Audio/video konverter Sharper Image
- Audio/video konverter A-NeuVideo
- Audio/video konverter SWIT
- Audio/video konverter I-Tec
- Audio/video konverter Newell
- Audio/video konverter Kanex
- Audio/video konverter TechLogix Networx
- Audio/video konverter Audibax
- Audio/video konverter Atlantis Land
- Audio/video konverter PTN-electronics
- Audio/video konverter Spatz
- Audio/video konverter PulseAudio
- Audio/video konverter ShieldRock
- Audio/video konverter Decimator
- Audio/video konverter Ferrofish
Nyeste Audio/video konverter Manualer
13 Januar 2025
12 Januar 2025
8 Januar 2025
5 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025