Boss BRRC34 Manual

Boss Soundbar BRRC34

Læs nedenfor 📖 manual på dansk for Boss BRRC34 (1 sider) i kategorien Soundbar. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

THIS PACKAGE CONTAINS

1 - BRRC34 Soundbar Speaker System

1 - Bluetooth Multi-Function Controller Kit

1 - 1.50” Rollbar Mounting Kit

1 - 1.75” / 2.00” Rollbar Mounting Kit

1 - Quick Connect Power Cable

1 - User Manual Quick Start Guide / Poster

1 - Warranty Card / Facebook Card

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other

antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by

user. This equipment complies with FCC/ IC radiation exposure limits set forth for

an uncontrolled environment and meets the FCC radio frequency (RF) Exposure

Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment has very low levels of RF energy that it deemed to comply without

maximum permissive exposure evaluation (MPE). But it is desirable that it should

be installed and operated keeping the radiator at least 20 cm or more away from

person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration

or modications carried out without appropriate authorization may invalidate the

user’s right to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guar-

antee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

□ Relocate or reorient the receiving antenna.

□ Increase the separation between the equipment and receiver.

□ Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

□ Consult the dealer or an experienced radio/TV technician for help.

USER MANUAL

QUICK START GUIDE

Thank you for purchasing this

BRRC34 Soundbar Sound System

Please read through these instructions carefully so you will know

how to operate your model properly.

After you have nished reading the instructions, keep this document

in a safe place for future reference.

INFORMATION TO THE USER

The Bluetooth® word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks is under license.

Other trademarks and trade names are those of their respective owners.

CAUTION!!

ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

GETTING TO KNOW YOUR

BRRC34 MULTIFUNCTION CONTROLLER (MFC)

BEFORE YOU START

IMPORTANT SAFETY PRECAUTIONS

■ Do not operate mobile equipment while driving a motorized vehicle – safe driving and

safety consideration of others should always be your highest priority

■ In the event you should notice smoke, strange noises or odor from this product, or any

other abnormal signs, immediately turn o the power and consult your dealer or the nearest

authorized BOSS AUDIO Service Center. Using this product in this condition may result in

permanent damage to the system

■ Set your volume control at a low setting, then slowly increase the sound until you can

hear it comfortably without distortion, or ear discomfort

■ :BE SURE TO OBSERVE THE FOLLOWING GUIDELINES

- Do not turn up the volume so high that you can’t hear what’s around you

- Use caution or temporarily discontinue use in potentially hazardous situations

INSTALLATION PRECAUTIONS

WARNING - Always consult a professional installer

■ Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without professional training and experience in electronic equipment

and motorized vehicle accessories may be dangerous and could expose you to the risk of

electric shock, injury or other hazards

■ Refer any repairs to a qualied BOSS AUDIO SYSTEMS Service Center

■ The BRRC34 should be hard wired directly to the main vehicle battery

■ When wiring directly to the vehicles battery, be sure to disconnect the batteries negative

terminal wire before starting any wiring procedures

■ The ground cable length should be short as possible (See wiring diagram)

■ The BRRC34 has a weather resistant design, it should not be under any circumstances

submerged in, or under water

■ Use only the supplied installation parts provided with the BRRC34

■ Wash with a mild detergent and lukewarm water using a clean sponge or a soft cloth

■ Rinse well with clean water

“DO NOT’S” - Very Important

■ DON’T clean in hot sun or on very hot days

■ DON’T use abrasive or highly alkaline cleaners on the main body

■ DON’T scrape the main body with razor blades, or other sharp instruments

■ DON’T ever use, gasoline, acetone or carbon tetrachloride

■ DON’T ever use a pressure washer aimed at the speakers

GETTING STARTED

MFC - MULTIFUNCTION CONTROLLER

DOME LIGHT ON/OFF - (Auto 10 minute timer when MFC ACC is turned OFF)

POWER ON - Press and hold for 3 seconds

EQ - EQ1 | EQ2 | EQ3 | FLAT - EQ1 Default Press and hold for 3 seconds

NEXT TRACK - FF press and hold

PLAY/PAUSE - AUX MUTE

BLUETOOTH PAIRING INDICATOR LED - BLUE / AUX RED COLOR

PREVIOUS TRACK - FR press and hold

VOLUME DOWN - Ramp DOWN press and hold

VOLUME UP - Ramp UP press and hold

CAUTION!! Using other mounting methods may void this warranty

PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION

1) Power on the by long-pressing the MFC 3 for 3 seconds, long-press the Power button

6 button for 3 seconds, the Bluetooth BLUE LED will start to rapidly ash, signalling that

the is now ready for pairingMFC Bluetooth

NOTE: You have 2 minutes before you must restart this procedure over again.

2) The MFC is now in pairing mode:

ANDROID users:

a. Go into the of your deviceSettings Menu

b. Enter the Bluetooth Menu

TURN ON Bluetooth SCANc. and press

d. “BOSS REBEL UTV” AVAILABLE DEVICESwill now be displayed under

e. If prompted, enter passcode: “ ”0000

iOS users:

a. Go into the of your deviceSettings Menu iOS

b. Enter the Bluetooth Menu

. TURN ON Bluetoothc

d. “BOSS REBEL UTV” will now be displayed

e. If prompted, enter passcode: “ ”0000

3) If is not seen, repeat the above steps to refresh the “BOSS REBEL UTV Device List”

4) When the connection is successful a tone will be heard, and the LED indicator Bluetooth

will light solid, you are now ready to stream music from your favorite media player to the MFC

Using this product without running the engine can drain the battery.

To avoid battery exhaustion, be sure to occasionally run the

vehicles engine while using this product.

BLUETOOTH OPERATION STREAMING MUSIC

RECONNECTION

1) Power on the and your last paired device Bluetooth.MFC

2) Ensure you are within range of the , the unit will now automatically reconnectMFC

3) If the device is out of range from the , it will disconnect automatically:MFC

a. The MFC will reconnect automatically to your device when in range

4) If your device was previously paired with the , but it wasn’t the last paired device:MFC

a. Ensure no other devices are currently paired

b. Enter the on your device being pairedBluetooth Menu

c. “BOSS REBEL UTV” AVAILABLE DEVICES will display under

d. Choose the to reconnect“BOSS REBEL UTV”

5) To clear all previously paired devices from memory, press and hold the MFC Bluetooth

button for 10 seconds

NOTE: Some devices may require a manual reconnection once the devices Bluetooth

Bluetooth OFF / ON BOSS REBEL UTVis powered and/or back in range, repress the

button in BLUETOOTH settings on your device

Tips:

MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION

1) Press the 5 PLAY/PAUSE PLAYonce to start playing music or press the button from

your devices touch screen

2) To skip songs or advance, press the 4 buttonNEXT TRACK

3) To select the previous song, press the 7 buttonPREVIOUS TRACK

VOLUME CONTROL

4) To raise the volume press the 9 VOLUME UP button or use your devices controls

5) To lower the volume press the 8 button or use your devices controls VOLUME DOWN

NOTE: If or is disconnected for more than 10 minutes the will BLUETOOTH AUX MFC

automatically turn , however, when not in use the switch should be manually OFF ACC

turned to keep the vehicles main battery from drainingOFF

MULTIFUNCTION CONTROLLER AUX-IN OPERATION

1) Power on the by pressing and holding down the MFC 3POWER button for 3 seconds

2) Disconnect any paired in your devices Bluetooth Bluetooth device by turning o

Settings Menu

3) Connect your 3.5mm cable located on front side of the to your devices AUX-IN MFC

headphone jack

4) Route the wire back to , secure your device in a safe locationMFC

VOLUME CONTROL

5) To raise the volume press the 9 VOLUME UP button

6) To lower the volume press the 8 button VOLUME DOWN

7) To MUTE the volume press the 5 PLAY/PAUSE button

AUX-INPUT

Make sure your device Bluetooth volume is set at 100% level

before stowing your device

BEFORE YOU START INSTALLATION

Make sure your device headphone volume is set at 100% level

before stowing your device

MFC can play audio from

any device that has a 3.5mm

headphone audio jack.

INSERT

(Cable not included)

YOUR

DEVICE

Tips:

MULTI-FUNCTION CONTROLLER MOUNTING

TOOLS NEEDED:

- Crimp Tool

- Wrench or Pliers

- 3mm Allen Wrench

MOUNTING THE SOUNDBAR

When replacing the fuse, be sure to only use a fuse of the rating specied on

this product. To avoid short-circuiting, cover any disconnected leads with insulating

tape. It is especially important to insulate any unused wires, which if left uncovered

may cause a short circuit. When connecting other devices to this product, refer to

the manual for the product to be connected. The black cable is ground, make sure

to connect the ground wire rst. Ensure that the ground wire is properly connected

to metal parts of the vehicles body frame or direct to the battery if your vehicle

does not have a grounded chassis frame The ground wire of this units power amp

and a second powered system must be connected to the frame separately with

dierent screws. If the screw for the ground wire loosens or falls out, it could result

in re or malfunction.

To avoid potential shorts in the electrical

system, be sure to disconnect the (–)

battery cable before installation. Use this

unit with a 12-Volt battery and negative

grounding only. Failure to do so may result

in a re or malfunction.

BRRC34

RECOIL SERIES

BLUETOOTH® | 34” AMPLIFIED SOUNDBAR SYSTEM

USER’S MANUAL

QUICK START GUIDE

BRRC34

USER’S MANUAL

RECOIL SERIES

34” AMPLIFIED SOUNDBAR SOUND SYSTEM

WITH BLUETOOTH REMOTE CONTROLLER

PRINTED IN CHINAVER:1.1 EN

iPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other countries

Android is a trademarks of Google Inc. registered in the U.S. and other countries.

BOSS Audio Systems is not aliated with Apple Inc. or Google Inc.

317

BOSS Audio Systems

3451 Lunar Court • Oxnard, CA 93030

www.bossaudio.com | 805-322-8794

Tech Support: www.bossaudio.com/support/technical-support

BLUETOOTH

• Version: 4.1

• A2DP / AVRCP / GATT

• Range: 33ft (10m) Class 2

• 20-Band DSP: 4 Preset EQ

• RCA Line Output: 2V RMS

SPEAKERS

• Dimension: 3.0”

• Cone Type: PP CARBON

• Tweeter Size: 1” SOFT DOME

AMPLIFIER

• Maximum Output Power: 700 Watts

• Input Impedance: 10kΩ

• Frequency Response: 45Hz-25kHz

GENERAL

• Operational Power: 14.4VDC (10-16V allowable)

• MAX Current Draw: 12.7A

• USB Charging: 1A @ 5VDC +/- 5%

• Replacement Fuse: 15A ATO TYPE

• Cabinet Material: Aluminum Extrusion

SPECIFICATIONS

WIRE DIAGRAM

5.55"

(141mm)

5.55"

(141mm)

33.77"

(858mm)

4.98"

Dimensions:

33.77" (858mm) x 4.98" (126.5 mm) x 5.55" (141mm)

Weight:

19.84 lbs (9 kg)

15A

Fuse and fuse holder

Chassis

ground

point

BATTERY Replace with 15A only

INSERT

DIRECT BATTERY WIRING CIRCUIT

RED

BLACK

Chassis

ground

point

MFC

Ground wire

Metal frame

( AUX Cable not included)

INSERT

RED

BLACK

ACC SWITCH

LINE OUT

(-) ORANGE

(+) BLUE

DOME LIGHT

AMP REMOTE INPUT

RIGHT

LEFT

GROUND

CRIMP

DAISY CHAIN

LINE OUTPUTS

LINE IN

(-) MOMENTARY TO ACTIVATE

• Color: Black Powder Coating

• Weight: 19.84lbs / 9.00kg

• Dimensions Inches WxHxD: 33.77 x 4.98 x 5.55

• Dimensions cm WxHxD: 85.8 x 12.6 x 14.1

• Storage Temperature: 5oF to 175oF / -15oC to 80oC

• Operation Temperature: 32 oF to 140oF / 0oC to 60oC

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO Inc.

BLUETOOTH OPERATION

CAUTION!!

Mounting brackets should be periodically checked to be sure they are tight

and secure before use of the vehicle.

CABLE NOT INCLUDED

1) Determine the size for your vehicle, install rubber on rollbar bushings rollbar

2) Insert and align notch of into the rubber bushings aluminum brackets

3) Apply supplied Loc-Tight allen bolt to tips, let dry for 20 minutes, then align

the and allen bolts T-nuts T-channel into the , rmly tighten

4) Recheck all are tight, ensure allen bolts T-nut’s are properly seated in the

T-channel correctly

Your Rollbar

Rubber Bushing

INSTALLATION PARTS

1.5”

1.75”

2”

RUBBER BUSHINGS

1.5”

1.75” or 2”

BRACKETS

ROLLBAR / CAGE MOUNT

ALIGN CONNECTOR

PINS, INSERT and

HAND TIGHTEN

1.5” 1.75” 2.00”

FLUSH MOUNT

SURFACE MOUNT

NEVER CONNECT +12V

TO THE DOME WIRE

LED DOME - ON/OFFMUTE - ON/OFF STATUS INDICATOR

WHITE = ON

RED = STANDBY

CAUTION:

NEVER CONNECT THE DIRECTLY MFC

TO THE BATTERY, ALWAYS USE AN

ACCESSORY SWITCH

CAUTION!!

Never use USB

or while in AUX

mud and/or water

Close USB cover

when not in use

ONBOARD CONTROL PANEL

Some applications may require

optional friction tape between

rubber bushings for a secure,

tight t, this can be found at

most local hardware stores

1) Always check mounting depth before cutting

2) Use the ush bezel as template

3) Cutout hole exactly

4) Insert ush mount bezel, push side tabs outwards

5) Use optional silicon glue to give extra hold

6) Insert MFC

1) Check mounting depth before drilling

2) Use the ush bezel as template

3) Drill or cut wire hole exactly

4) Insert rubber trim around ush bezel,

screw in place

5) Insert MFC

MFC can rotate 90o for the

best mounting position

3mm Allen Head

T-nut must be assembled

in this conguration

Align notch

OPTIONAL

OPTIONAL TOOLS NEEDED:

- Hand saw or Jigsaw

NOTE!!

To conserve battery life, the LED Dome light will automatically turn o after

10 minutes when MFC ACC is turned OFF

BOSS REFLEX SERIES

OPTIONAL SYSTEM

EXPANSIBILITY

3.5mm AUX-INPUT

USB 1A

CHARGING

NOT FOR AUDIO PLAYBACK

OPEN

ALWAYS CLOSE COVER WHEN

NOT IN USE NEVER USE WHEN

IN MUD and/or WATER

MFC RESET

LONG PRESS BOSS

LOGO FOR 10 SECONDS

Produkt Specifikationer

Mærke:	Boss
Kategori:	Soundbar
Model:	BRRC34

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss BRRC34 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Soundbar Boss Manualer

Boss BRRF46A Manual

14 August 2024

Boss BRT26RGB Manual

14 August 2024

Boss ATV30BRGB Manual

13 August 2024

11 August 2024

11 August 2024

11 August 2024

11 August 2024

10 August 2024

10 August 2024

10 August 2024

Soundbar Manualer

Nyeste Soundbar Manualer

Pyle PWPSB2403 Manual

14 November 2024

Pyle PWPSB1103 Manual

13 November 2024

Bose Solo Sounbar Series II Manual

5 November 2024

Samsung HW-K561 Manual

2 November 2024

Bauhn ASBBT-0724 Manual

19 Oktober 2024

Samsung HW-K660 Manual

19 Oktober 2024

Grundig GSB 930 Manual

18 Oktober 2024

Insignia NS-HTSB20S Manual

15 Oktober 2024

JVC TH-E324B Manual

10 Oktober 2024

Samsung HW-J8511 Manual

4 Oktober 2024