Boss BRRF46 Manual
Læs nedenfor 📖 manual på dansk for Boss BRRF46 (1 sider) i kategorien Soundbar. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/boss/brrf46/html/bg1.png)
THIS PACKAGE CONTAINS
1 - BRRF46 Overhead Speaker System
1 - Bluetooth Multi-Function Controller Kit
2 - 1.75” / 2.00” Rollbar Mounting Kit
1 - Quick Connect Power Cable
1 - User Manual Quick Start Guide / Poster
1 - Warranty Card / Facebook Card
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by
user. This equipment complies with FCC/ IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator at least 20 cm or more away from
person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration
or modications carried out without appropriate authorization may invalidate the
user’s right to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
□ Relocate or reorient the receiving antenna.
□ Increase the separation between the equipment and receiver.
□ Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
□ Consult the dealer or an experienced radio/TV technician for help.
USER MANUAL
QUICK START GUIDE
Thank you for purchasing this
BRRF46 Soundbar Sound System
Please read through these instructions carefully so you will know
how to operate your model properly.
After you have nished reading the instructions, keep this document
in a safe place for future reference.
INFORMATION TO THE USER
INFORMATION TO THE USER
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks is under license.
Other trademarks and trade names are those of their respective owners.
CAUTION!!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
GETTING TO KNOW YOUR
BRRF46 MULTIFUNCTION CONTROLLER (MFC)
BEFORE YOU START
IMPORTANT SAFETY PRECAUTIONS
■ Do not operate mobile equipment while driving a motorized vehicle – safe driving and
safety consideration of others should always be your highest priority
■ In the event you should notice smoke, strange noises or odor from this product, or any
other abnormal signs, immediately turn o the power and consult your dealer or the nearest
authorized BOSS AUDIO Service Center. Using this product in this condition may result in
permanent damage to the system
■ Set your volume control at a low setting, then slowly increase the sound until you can
hear it comfortably without distortion, or ear discomfort
■ :BE SURE TO OBSERVE THE FOLLOWING GUIDELINES
- Do not turn up the volume so high that you can’t hear what’s around you
- Use caution or temporarily discontinue use in potentially hazardous situations
INSTALLATION PRECAUTIONS
WARNING - Always consult a professional installer
■ Do not attempt to install or service this product by yourself. Installation or servicing of this
product by persons without professional training and experience in electronic equipment
and motorized vehicle accessories may be dangerous and could expose you to the risk of
electric shock, injury or other hazards
■ Refer any repairs to a qualied BOSS AUDIO SYSTEMS Service Center
■ The BRRF46 should be hard wired directly to the main vehicle battery
■ When wiring directly to the vehicles battery, be sure to disconnect the batteries negative
terminal wire before starting any wiring procedures
■ The ground cable length should be short as possible (See wiring diagram)
■ The BRRF46 has a weather resistant design, it should not be under any circumstances
submerged in, or under water
■ Use only the supplied installation parts provided with the BRRF46
■ Wash with a mild detergent and lukewarm water using a clean sponge or a soft cloth
■ Rinse well with clean water
“DO NOT’S” - Very Important
■ DON’T clean in hot sun or on very hot days
■ DON’T use abrasive or highly alkaline cleaners on the main body
■ DON’T scrape the main body with razor blades, or other sharp instruments
■ DON’T ever use, gasoline, acetone or carbon tetrachloride
■ DON’T ever use a pressure washer aimed at the speakers
GETTING STARTED
A
1
2
3
4
5
6
7
8
9
MFC - MULTIFUNCTION CONTROLLER
DOME LIGHT ON/OFF - (Auto 10 minute timer when MFC ACC is turned OFF)
POWER ON - Press and hold for 3 seconds
EQ - EQ1 | EQ2 | EQ3 | FLAT - EQ1 Default Press and hold for 3 seconds
NEXT TRACK - FF press and hold
PLAY/PAUSE - AUX MUTE
BLUETOOTH PAIRING INDICATOR LED - BLUE / AUX RED COLOR
PREVIOUS TRACK - FR press and hold
VOLUME DOWN - Ramp DOWN press and hold
VOLUME UP - Ramp UP press and hold
CAUTION!! Using other mounting methods may void this warranty
PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION
1) Power on the by long-pressing the MFC 3 for 3 seconds, long-press the Power button
6 button for 3 seconds, the Bluetooth BLUE LED will start to rapidly ash, signalling that
the is now ready for pairingMFC Bluetooth
NOTE: You have 2 minutes before you must restart this procedure over again.
2) The MFC is now in pairing mode:
ANDROID users:
a. Go into the of your deviceSettings Menu
b. Enter the Bluetooth Menu
TURN ON Bluetooth SCANc. and press
d. “BOSS REBEL UTV” AVAILABLE DEVICESwill now be displayed under
e. If prompted, enter passcode: “ ”0000
iOS users:
a. Go into the of your deviceSettings Menu iOS
b. Enter the Bluetooth Menu
. TURN ON Bluetoothc
d. “BOSS REBEL UTV” will now be displayed
e. If prompted, enter passcode: “ ”0000
3) If is not seen, repeat the above steps to refresh the “BOSS REBEL UTV Device List”
4) When the connection is successful a tone will be heard, and the LED indicator Bluetooth
will light solid, you are now ready to stream music from your favorite media player to the MFC
Using this product without running the engine can drain the battery.
To avoid battery exhaustion, be sure to occasionally run the
vehicles engine while using this product.
BLUETOOTH OPERATION STREAMING MUSIC
RECONNECTION
1) Power on the and your last paired device Bluetooth.MFC
2) Ensure you are within range of the , the unit will now automatically reconnectMFC
3) If the device is out of range from the , it will disconnect automatically:MFC
a. The MFC will reconnect automatically to your device when in range
4) If your device was previously paired with the , but it wasn’t the last paired device:MFC
a. Ensure no other devices are currently paired
b. Enter the on your device being pairedBluetooth Menu
c. “BOSS REBEL UTV” AVAILABLE DEVICES will display under
d. Choose the to reconnect“BOSS REBEL UTV”
5) To clear all previously paired devices from memory, press and hold the MFC Bluetooth
button for 10 seconds
NOTE: Some devices may require a manual reconnection once the devices Bluetooth
Bluetooth OFF / ON BOSS REBEL UTVis powered and/or back in range, repress the
button in BLUETOOTH settings on your device
3
Tips:
MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION
1) Press the 5 PLAY/PAUSE PLAYonce to start playing music or press the button from
your devices touch screen
2) To skip songs or advance, press the 4 buttonNEXT TRACK
3) To select the previous song, press the 7 buttonPREVIOUS TRACK
VOLUME CONTROL
4) To raise the volume press the 9 VOLUME UP button or use your devices controls
5) To lower the volume press the 8 button or use your devices controls VOLUME DOWN
NOTE: If or is disconnected for more than 10 minutes the will BLUETOOTH AUX MFC
automatically turn , however, when not in use the switch should be manually OFF ACC
turned to keep the vehicles main battery from drainingOFF
MULTIFUNCTION CONTROLLER AUX-IN OPERATION
1) Power on the by pressing and holding down the MFC 3POWER button for 3 seconds
2) Disconnect any paired in your devices Bluetooth Bluetooth device by turning o
Settings Menu
3) Connect your 3.5mm cable located on front side of the to your devices AUX-IN MFC
headphone jack
4) Route the wire back to , secure your device in a safe locationMFC
VOLUME CONTROL
5) To raise the volume press the 9 VOLUME UP button
6) To lower the volume press the 8 button VOLUME DOWN
7) To MUTE the volume press the 5 PLAY/PAUSE button
AUX-INPUT
Make sure your device Bluetooth volume is set at 100% level
before stowing your device
BEFORE YOU START INSTALLATION
Make sure your device headphone volume is set at 100% level
before stowing your device
MFC can play audio from
any device that has a 3.5mm
headphone audio jack.
INSERT
(Cable not included)
YOUR
DEVICE
Tips:
Tips:
MULTI-FUNCTION CONTROLLER MOUNTING
TOOLS NEEDED:
- Crimp Tool
- Wrench or Pliers
- 3mm Allen Wrench
MOUNTING THE OVERHEAD SOUNDBAR
When replacing the fuse, be sure to only use a fuse of the rating specied on
this product. To avoid short-circuiting, cover any disconnected leads with insulating
tape. It is especially important to insulate any unused wires, which if left uncovered
may cause a short circuit. When connecting other devices to this product, refer to
the manual for the product to be connected. The black cable is ground, make sure
to connect the ground wire rst. Ensure that the ground wire is properly connected
to metal parts of the vehicles body frame or direct to the battery if your vehicle
does not have a grounded chassis frame The ground wire of this units power amp
and a second powered system must be connected to the frame separately with
dierent screws. If the screw for the ground wire loosens or falls out, it could result
in re or malfunction.
To avoid potential shorts in the electrical
system, be sure to disconnect the (–)
battery cable before installation. Use this
unit with a 12-Volt battery and negative
grounding only. Failure to do so may result
in a re or malfunction.
BRRF46
REFLEX SERIES
BLUETOOTH® | 46” SIDE x SIDE | AMPLIFIED OVERHEAD SYSTEM
USER’S MANUAL
QUICK START GUIDE
BRRF46
USER’S MANUAL
REFLEX SERIES
46” SIDE x SIDE | AMPLIFIED OVERHEAD SOUND SYSTEM
WITH BLUETOOTH REMOTE CONTROLLER
PRINTED IN CHINAVER:1.1 EN
iPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other countries
Android is a trademarks of Google Inc. registered in the U.S. and other countries.
BOSS Audio Systems is not aliated with Apple Inc. or Google Inc.
317
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
www.bossaudio.com | 805-322-8794
Tech Support: www.bossaudio.com/support/technical-support
BLUETOOTH
• Version: 4.1
• A2DP / AVRCP / GATT
• Range: 33ft (10m) Class 2
• 20-Band DSP: 4 Preset EQ
• RCA Line Output: 2V RMS
SPEAKERS
• Dimension: 6.5” MID + 8” SUB
• MID Cone Type: PP Carbon
• Tweeter Size: 1” Titanium
AMPLIFIER
• Maximum Output Power: 1000 Watts
• Input Impedance: 10kΩ
• Frequency Response: 45Hz-25kHz
GENERAL
• Operational Power: 14.4VDC (10-16V allowable)
• MAX Current Draw: 12.7A
• USB Charging: 1A @ 5VDC +/- 5%
• Replacement Fuse: 15A ATO TYPE
• Cabinet Material: High Impact ABS
SPECIFICATIONS
WIRE DIAGRAM
10.24"
(260mm)
10.24"
(260mm)
46.06"
(1170mm)
4.09"
(104mm)
Dimensions:
46.06" (1170mm) x 4.09" (104mm) x 10.24" (260mm)
Weight:
27.5 lbs (12.5 kg)
15A
Fuse and fuse holder
Chassis
ground
point
BATTERY Replace with 15A only
INSERT
DIRECT BATTERY WIRING CIRCUIT
RED
BLACK
Chassis
ground
point
MFC
Ground wire
Metal frame
( AUX Cable not included)
INSERT
RED
BLACK
ACC SWITCH
LINE OUT
(-) ORANGE
(+) BLUE
DOME LIGHT
AMP REMOTE INPUT
RIGHT
LEFT
GROUND
CRIMP
DAISY CHAIN
LINE OUTPUTS
LINE IN
(-) MOMENTARY TO ACTIVATE
3A
• Color: Black
• Weight: 27.5lbs / 12.5kg
• Dimensions Inches WxHxD: 46.06 x 4.09 x 10.24
• Dimensions cm WxHxD: 117.0 x 10.4 x 26.0
• Storage Temperature: 5 oF to 175oF / -15oC to 80oC
• Operation Temperature: 32 oF to 140oF / 0oC to 60oC
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including
photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO Inc.
Copyright © 2017 BOSS AUDIO Inc.
BLUETOOTH OPERATION
CAUTION!!
Mounting brackets should be periodically checked to be sure they are tight
and secure before use of the vehicle.
CABLE NOT INCLUDED
46
6
7
4
5
8
9
5
8
9
3
1) Determine the best location on your for your vehicle, install rubber rollbar
bushings rollbar, ensure there is ample head spaceon the
2) Apply supplied Loc-Tight allen bolt to tips, let dry for 20 minutes
3) Wrap C-clamp around rollbar, hand tighten the allen-head bolts
4) Insert left/right slide rails into , some vehicles will require REFLEX Soundbar
the use of the rotation bracket, allowing adjustments up to +/- 10 degrees
5) Carefully set the on top of the C-clamp, hand tighten the REFLEX Soundbar
allen head screws
6) Center the , permanently tighten all the REFLEX Soundbar allen bolts and nuts
Your Rollbar
Rubber Bushing
ROTATE
BRACKET OPTIONS
ROLLBAR / CAGE MOUNT
ALIGN CONNECTOR
PINS, INSERT and
HAND TIGHTEN
1.5” 1.75” 2.00”
FLUSH MOUNT
SURFACE MOUNT
NEVER CONNECT +12V
TO THE DOME WIRE
LED DOME - ON/OFFMUTE - ON/OFF STATUS INDICATOR
WHITE = ON
RED = STANDBY
CAUTION:
NEVER CONNECT THE DIRECTLY MFC
TO THE BATTERY, ALWAYS USE AN
ACCESSORY SWITCH
CAUTION!!
Never use USB
or while in AUX
mud and/or water
Close USB cover
when not in use
ONBOARD CONTROL PANEL
Some applications may require
optional friction tape between
rubber bushings for a secure,
tight t, this can be found at
most local hardware stores
1) Always check mounting depth before cutting
2) Use the ush bezel as template
3) Cutout hole exactly
4) Insert ush mount bezel, push side tabs outwards
5) Use optional silicon glue to give extra hold
6) Insert MFC
1) Check mounting depth before drilling
2) Use the ush bezel as template
3) Drill or cut wire hole exactly
4) Insert rubber trim around ush bezel,
screw in place
5) Insert MFC
MFC can rotate 90o for the
best mounting position
3mm Allen Head
3mm Allen Head
OPTIONAL
OPTIONAL
OPTIONAL TOOLS NEEDED:
- Hand saw or Jigsaw
NOTE!!
To conserve battery life, the LED Dome light will automatically turn o after
10 minutes when MFC ACC is turned OFF
BOSS RECOIL SERIES
OPTIONAL SYSTEM
EXPANSIBILITY
87
4
23
A
9
3.5mm AUX-INPUT
USB 1A
CHARGING
NOT FOR AUDIO PLAYBACK
OPEN
ALWAYS CLOSE COVER WHEN
NOT IN USE NEVER USE WHEN
IN MUD and/or WATER
1
5
6
MFC RESET
LONG PRESS BOSS
LOGO FOR 10 SECONDS
Fender Washer
3mm Allen Head
Produkt Specifikationer
Mærke: | Boss |
Kategori: | Soundbar |
Model: | BRRF46 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Boss BRRF46 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Soundbar Boss Manualer
![Boss](/images/pdf_free.png)
14 August 2024
![Boss](/images/pdf_free.png)
14 August 2024
![Boss](/images/pdf_free.png)
13 August 2024
![Boss](/images/pdf_free.png)
11 August 2024
![Boss](/images/pdf_free.png)
11 August 2024
![Boss](/images/pdf_free.png)
11 August 2024
![Boss](/images/pdf_free.png)
11 August 2024
![Boss](/images/pdf_free.png)
10 August 2024
![Boss](/images/pdf_free.png)
10 August 2024
![Boss](/images/pdf_free.png)
9 August 2024
Soundbar Manualer
- Soundbar Denver
- Soundbar TCL
- Soundbar Sony
- Soundbar Samsung
- Soundbar Panasonic
- Soundbar Philips
- Soundbar Lenco
- Soundbar OK
- Soundbar LG
- Soundbar Pioneer
- Soundbar Sharp
- Soundbar Technaxx
- Soundbar MB Quart
- Soundbar Sennheiser
- Soundbar Harman Kardon
- Soundbar Grundig
- Soundbar Livoo
- Soundbar Pyle
- Soundbar Furrion
- Soundbar Denon
- Soundbar Yamaha
- Soundbar Infiniton
- Soundbar Bowers & Wilkins
- Soundbar Nedis
- Soundbar Kicker
- Soundbar Hama
- Soundbar Auna
- Soundbar Muse
- Soundbar Element
- Soundbar Creative
- Soundbar Thomson
- Soundbar Aiwa
- Soundbar JBL
- Soundbar AKAI
- Soundbar Hisense
- Soundbar Teufel
- Soundbar Maxell
- Soundbar Trevi
- Soundbar Trust
- Soundbar Blaupunkt
- Soundbar JVC
- Soundbar Razer
- Soundbar Medion
- Soundbar Megasat
- Soundbar Haier
- Soundbar Cambridge
- Soundbar König
- Soundbar Bose
- Soundbar Klipsch
- Soundbar Libratone
- Soundbar Vaddio
- Soundbar Dali
- Soundbar Krüger&Matz
- Soundbar Dell
- Soundbar Schneider
- Soundbar NGS
- Soundbar NEC
- Soundbar Sonos
- Soundbar Reflecta
- Soundbar Energy Sistem
- Soundbar Sonance
- Soundbar Salora
- Soundbar Onkyo
- Soundbar Focal
- Soundbar Nevir
- Soundbar Magnat
- Soundbar ELAC
- Soundbar Sven
- Soundbar Bluesound
- Soundbar Polk
- Soundbar Yealink
- Soundbar Audizio
- Soundbar Jamo
- Soundbar AV:link
- Soundbar Renkforce
- Soundbar BlueAnt
- Soundbar ILive
- Soundbar VIZIO
- Soundbar Continental Edison
- Soundbar GPX
- Soundbar Martin Logan
- Soundbar Fosi Audio
- Soundbar Canton
- Soundbar Memphis Audio
- Soundbar GoGen
- Soundbar Kogan
- Soundbar Definitive Technology
- Soundbar Insignia
- Soundbar Boston Acoustics
- Soundbar Steren
- Soundbar PowerBass
- Soundbar Aconatic
- Soundbar Orbitsound
- Soundbar Proscan
- Soundbar Sylvania
- Soundbar Kubo
- Soundbar Mac Audio
- Soundbar Laser
- Soundbar Naxa
- Soundbar Pure Acoustics
- Soundbar Integra
- Soundbar Bazooka
- Soundbar Monoprice
- Soundbar PSB
- Soundbar Wet Sounds
- Soundbar MTX Audio
- Soundbar Astell&Kern
- Soundbar GoldenEar
- Soundbar EKO
- Soundbar GoldenEar Technology
- Soundbar Thonet & Vander
- Soundbar Edis
- Soundbar Majority
Nyeste Soundbar Manualer
![Klipsch](/images/logos/klipsch.png)
9 September 2024
![Kubo](/images/pdf_free.png)
9 September 2024
![Teufel](/images/pdf_free.png)
7 September 2024
![Samsung](/images/logos/samsung.png)
7 September 2024
![Polk](/images/pdf_free.png)
7 September 2024
![LG](/images/logos/lg.png)
6 September 2024
![Majority](/images/pdf_free.png)
6 September 2024
![Majority](/images/pdf_free.png)
6 September 2024
![Majority](/images/pdf_free.png)
6 September 2024
![Majority](/images/pdf_free.png)
6 September 2024