Elba ETM-E3690P Manual
Læs nedenfor 📖 manual på dansk for Elba ETM-E3690P (1 sider) i kategorien Vandhane. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
ETM-E3690P
1. An opening hole of 35mm diameter is required on sink top or work top (C) for installation of tap.
2. Slide the rubber O-ring (B) up to the base of tap (A).
3.Screw the flex hoses (H) up to the extension tube, then insert the tap through the hole of sink top or
worktop (C), and position the tap properly.
4.Slide the plastic fitting I (D) through the extension tube ,then slide the plastic fitting II (E) through the
sprayer hose and up to the plastic fitting I(D).
Important: ensure the opening of plastic fitting I (D) is close to threaded tube , and the sprayer hose
runs freely through the plastic fitting II (E).
5.Put the permanent seat(F) through the threaded tube , and tighten the fixing washer(G) securely.
Important: make sure the hose runs smoothly before tightened the fixing washer.
6.Connect the flex hoses (H) to the hot & cold water supply, and the sprayer hose to the threaded tube.
7. Adjusting the pull-out length of sprayer hose and fasten the weighing ball (I) with screws.
●Before installation, please ensure that the following
work conditions are adhered to:
-Water temperature between 0 C - 90 C˚ ˚
-Water pressure between 0.05MPa – 1.0MPa. Pressure
reducing valve is necessary if pressure exceeds 1.2MPa
-Avoid major pressure di erences between hot and cold ff
water supply
●Flush pipes thoroughly before and after installation to
ensure water supply is free of any debris.
●Inspect tap fitting and debugged to its best. Do not
attempt to disassemble fitting on your own.
●Use thread sealant tape (PTFE) on any screw joining
connections and ensure all joints are securely tightened.
A Tap body
B Rubber O ring
C Sink top or work
top
D Plastic fitting I
E Plastic fitting Ⅱ
F Permanent seat
G Fix ing washer
H Flex hose
I Weighing ball
J Rubber washer
for flexi hose
This . FIAMMA SDN. BHD. will not be held responsible for the use of superseded or voided specifications.
Fabricatoe must check for cut-out accuracy.
specification is subject to change without notice
Stainless Steel Mixer Tap
Produkt Specifikationer
| Mærke: | Elba |
| Kategori: | Vandhane |
| Model: | ETM-E3690P |
Har du brug for hjælp?
Hvis du har brug for hjælp til Elba ETM-E3690P stil et spørgsmål nedenfor, og andre brugere vil svare dig
Vandhane Elba Manualer
19 August 2024
19 August 2024
19 August 2024
19 August 2024
19 August 2024
Vandhane Manualer
- Vandhane Ikea
- Vandhane Siemens
- Vandhane Concept
- Vandhane Teka
- Vandhane Ernesto
- Vandhane Etna
- Vandhane Hansgrohe
- Vandhane Smeg
- Vandhane Miomare
- Vandhane KitchenAid
- Vandhane Svedbergs
- Vandhane Caple
- Vandhane Franke
- Vandhane Brita
- Vandhane Damixa
- Vandhane Oras
- Vandhane Grohe
- Vandhane Netatmo
- Vandhane Inventum
- Vandhane CDA
- Vandhane Mueller
- Vandhane Oliveri
- Vandhane Delta
- Vandhane Elkay
- Vandhane Haceka
- Vandhane Moen
- Vandhane Suprema
- Vandhane American Standard
- Vandhane Puretec
- Vandhane Sussex
- Vandhane Zurn
- Vandhane Karran
- Vandhane Jacuzzi
- Vandhane ProFlo
- Vandhane Pfister
Nyeste Vandhane Manualer
18 December 2024
18 December 2024
18 December 2024
18 December 2024
13 December 2024
13 December 2024
12 December 2024
12 December 2024
12 December 2024
12 December 2024