JVC UX-VJ3 Manual

JVC Højttaler UX-VJ3

Læs nedenfor 📖 manual på dansk for JVC UX-VJ3 (4 sider) i kategorien Højttaler. Denne guide var nyttig for 30 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

ENGLISH

GVT0330-001D[B/J/UJ/US/UN/UB/UX/A/UH]

0411WMKMDWJMM

MICRO COMPONENT SYSTEM

INSTRUCTIONS

UX-VJ5-W —Consists of CA-UXVJ5-W and SP-UXVJ5-W

UX-VJ5-V —Consists of CA-UXVJ5-V and SP-UXVJ5-V

UX-VJ5-G —Consists of CA-UXVJ5-G and SP-UXVJ5-G

UX-VJ5-P —Consists of CA-UXVJ5-P and SP-UXVJ5-P

UX-VJ5-B —Consists of CA-UXVJ5-B and SP-UXVJ5-B

UX-VJ5-T —Consists of CA-UXVJ5-T and SP-UXVJ5-T

UX-VJ3-W —Consists of CA-UXVJ3-W and SP-UXVJ5-W

UX-VJ3-G —Consists of CA-UXVJ3-G and SP-UXVJ5-G

UX-VJ3-B —Consists of CA-UXVJ3-B and SP-UXVJ5-B

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent

damage, locate the apparatus as follows:

Front: No obstructions and open spacing.

Sides/Top/Back: No obstructions should be placed

in the areas indicated by the dimensions in the

illustration.

Bottom: Place on the level surface. Maintain an

adequate air path for ventilation by placing on a stand

with a height of 10 cm or more.

ATTENTION: Aération correcte

Pour prévenir tout risque de décharge électrique

ou d’incendie et éviter toute détérioration, installez

l’appareil de la manière suivante:

Avant: Bien dégagé de tout objet.

Flancs/ Dessus/ Arrière: Aucun obstacle ne doit être

placé dans les zones indiquées par les dimensions

dans l’illustration.

Dessous: Posez l’appareil sur une surface plane et

horizontale. Veillez à ce que sa ventilation correcte

puisse se faire en le plaçant sur un support d’au moins

dix centimètres de hauter.

Front view / Face

Side view / Côté

Speaker

Enceinte

Main unit

Appareil principal

Speaker

Enceinte

Main unit

Appareil principal

Thank you for purchasing a JVC product.

In this manual...

Illustrations of UX-VJ5 are mainly used for explanation.

The remote control buttons are used for explaining the operations unless mentioned otherwise. However, if the

System has the same or similar button names, they can also be used for the operations.

“File” and “track” are used interchangeably.

•

(Europe only)

For customer use:

Enter below the Model No. and Serial No. which are

located either on the rear, bottom or side of the cabinet.

Retain this information for future reference.

Model No.

Serial No.

Notes on the power cord

When you go away for an extended period of time,

remove the plug from the wall outlet.

When unplugging the System from the wall outlet,

always pull the plug, not the power cord.

Do not handle the power cord with wet hands.

Disconnect the power cord before cleaning the System

or moving the System.

Do not alter, twist or pull the power cord, or put

anything heavy on it, which may cause fire, electric

shock, or other accidents.

Avoid moisture, water, dust, and high temperatures

Do not place the System in moist or dusty places.

If water gets inside the System, turn off the power and

remove the plug from the wall outlet, then consult your

dealer. Using the System in this state may cause a fire or

electrical shock.

Do not expose the System to direct sunlight or place it

near a heating device.

•

Notes on installation

Select a place which is level, dry and neither too hot nor

too cold—between 5˚C and 35˚C (41˚F and 95˚F).

Do not install the System in a place subject to vibrations.

Do not put heavy objects on the System.

To prevent malfunction or damage to the System

Do not insert any metallic objects, such as wires,

hairpins, coins, etc. into the System.

Do not block the vents.

There are no user-serviceable parts inside. If anything

goes wrong, unplug the power cord and consult your

dealer.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery

which contains Perchlorate Material—special handling

may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

•

Compatible iPod/iPhone/iPad

models

Made for Audio Video

iPod nano (6th generation) *

iPod nano (5th generation)

iPod nano (4th generation)

iPod nano (3rd generation)

iPod nano (2nd generation) –

iPod touch (4th generation)

iPod touch (3rd generation)

iPod touch (2nd generation)

iPod touch

iPod classic

iPhone 4

iPhone 3GS

iPhone 3G

iPad

* Only for still picture

If iPod/iPhone/iPad does not play correctly, update iPod

software to the latest version.

For details about updating iPod/iPhone/iPad, check on

the Apple web site <http://www.apple.com>.

Playable disc/file

This System can play back...

Audio CD and CD-R/CD-RW in Audio CD format

MP3/WMA files on a CD-R/CD-RW (ISO 9660 format),

USB mass storage class device (maximum data transfer

rate: 2 Mbps).

This System cannot play “packet write” discs.

This System can recognize up to 255 groups and 999

files.

For MP3/WMA playback:

Some MP3/WMA files may not be played back due to

their recording conditions.

It is recommended to record each file at a sampling

rate of 44.1 kHz and at a data transfer rate of 128 kbps.

This System can show the Tag data.

For playback of files on a USB mass storage class device:

You cannot play back files larger than 2 GB.

This System may not play back some USB mass storage

class devices and does not support DRM (Digital Rights

Management).

•

−

•

−

•

−

Notes on installing speakers

CAUTION:

Do not drag or push the speakers along the floor or

table. Otherwise, the foot spacers on the bottom may

peel off or drop from the speakers.

Install the speakers on a flat level surface to ensure the

best sound quality.

The sound may be affected by the location in which

you install them. To avoid such issues, change the

location and orientation of the speakers.

For cathode-ray tube televisions (CRT):

If you install the speakers near the TV, color distortion

may occur. To prevent this, turn off the TV’s main

power or unplug it before installing the speakers. Wait

at least 30 minutes before turning on the TV’s main

power again.

If the TV is still affected, move the unit further away.

Maintenance

To get the best performance of the System, keep your

discs and the mechanism clean.

Handling discs

Remove the disc from its case by holding it at the edge

while pressing the center hole lightly.

Do not touch the shiny surface of the disc, or bend the

disc.

Put the disc back in its case after use.

Be careful not to scratch the surface of the disc when

placing it back in its case.

Avoid exposure to direct sunlight, temperature

extremes, and moisture.

To clean the disc:

Wipe the disc with a soft cloth in a straight line from

center to edge.

Cleaning the System

Stains should be wiped off with a soft cloth. If the

System is heavily stained, wipe it with a cloth soaked in

water-diluted neutral detergent and wrung well, then

wipe clean with a dry cloth.

Since the System may deteriorate in quality, become

damaged or get its paint peeled off, be careful about the

following:

DO NOT wipe it hard.

DO NOT wipe it with thinner or benzine.

DO NOT apply any volatile substances such as

insecticides to it.

DO NOT allow any rubber or plastic to remain in

contact for a long time.

•

−

•

−

•

−

Troubleshooting

If you are having a problem with your System, check this list for a possible solution before calling for service.

General

Power does not come on. Power plug is not inserted securely. Plug it in securely.\

Adjustments or settings are suddenly

canceled before you finish.

There is a time limit. Start the procedure again.\

Unable to operate the System from the

remote control.

The path between the remote control and the remote sensor on

the System is blocked.

The battery is exhausted.

No sound is heard from the speakers. Speaker connections are incorrect or loose.

Headphones are connected.

FM/AM radio

Hard to listen to broadcasts because of noise. Antenna connection is incorrect or loose.

The AM loop antenna is too close to the System.

The FM antenna is not properly extended and positioned.

Electrostatic discharge from your body may cause noise. If this

happens, turn the System off then on again.

iPod/iPhone/iPad

The iPod/iPhone/iPad does not play, but

“CONNECT” appears on the display.

The battery of iPod/iPhone/iPad is low or exhausted. Charge the

battery of iPod/iPhone/iPad.

Disc/USB

The disc/USB mass storage class device does

not play.

The disc is placed incorrectly. Place the disc with the label side

facing forward.

The disc is recorded using “packet writing (UDF file system).” It

cannot be played.

The USB mass storage class device is not connected properly.

“NO DATA” appears on the display. No MP3/WMA files are recorded on the USB mass storage class

device.

Groups and tracks are not played back as you

expect.

Playing order is determined when the groups and tracks are

recorded. It depends on the writing application.

The disc/USB mass storage class device

sound is discontinuous.

The disc is scratched or dirty.

MP3/WMA files have not been properly recorded on the USB mass

storage class device.

Sound from the USB mass storage class

device is interrupted.

Noise and static electricity may stop the sound. In this case,

disconnect and connect the USB mass storage class device again

after turning off the System.

The slide door does not open or close. The AC power cord is not plugged in.

iPad is connected (“NO OPE” appears on the display). Disconnect it

before opening the slide door.

Disc ejection is prohibited. “LOCKED” appears (see “Prohibiting disc

ejection” on page 2).

Timer

Wake up Timer does not work. The System was turned on before the on-time came. The timer

starts working only when the System is turned off.

Main unit (CA-UXVJ5-W/CA-UXVJ5-V/CA-UXVJ5-G/

CA-UXVJ5-P/CA-UXVJ5-B/CA-UXVJ5-T/CA-UXVJ3-W/

CA-UXVJ3-G/CA-UXVJ3-B)

General

Power source (DC IN): DC 19 V 3.37 A

AC adaptor (AA-R1904):

Input: AC 100 V − 240 V , 50 Hz/60 Hz, 1.5 A – 0.9 A

Output: DC 19 V 3.37 A

Power consumption (on standby): 0.50 W or less

Dimensions (approx.) (W x H x D):

290 mm × 186.5 mm × 155 mm (11-7/16” x 7-3/8” x 6-1/8”)

Mass (approx.): UX-VJ5: 1.5 k (3.3 lbs)g

UX-VJ3: 1.4 k (3.1 lbs)g

Amplifier

Output Power: 30 W (15 W + 15 W) at 6 Ω (10% THD)

Audio Input: AUDIO IN: Stereo mini (ø 3.5 mm)

500 mV /50 kΩ (at “Level 1”)

250 mV /50 kΩ (at “Level 2”)

125 mV /50 kΩ (at “Level 3”)

Audio Output: SUBWOOFER OUT: 1 V/10 kΩ

HEADPHONE: 5 mW/32 Ω

Speaker impedance: 6 Ω – 16 Ω

Tuner

FM frequency:

For USA and Canadian models: 87.5 MHz – 108.0 MHz

For other models: 87.50 MHz – 108.00 MHz

AM (MW) frequency:

For European models: 522 kHz – 1 629 kHz

For USA and Canadian models:

530 kHz

–

1 710 kHz

For Saudi Arabia: 531 kHz – 1 602 kHz (at 9 kHz intervals)

530 kHz – 1 600 kHz (at 10 kHz intervals)

For other models: 531 kHz – 1 710 kHz (at 9 kHz intervals)

530 kHz – 1 710 kHz (at 10 kHz intervals)

USB (for PC IN)

USB Input: USB AUDIO

Compatible OS: Microsoft® 7 (32 bit/64 bit)

Windows Vista® (32 bit, SP2 or later)

Windows® XP (32 bit, SP3 or later)

In some cases, the operations may not be possible even

if one of the above OS is installed.

USB (for USB mass storage class device)

Not equipped for UX-VJ3 USA and Canadian models.

USB specification: Compatible with USB 2.0 Full Speed

Compatible device: Mass storage class

Compatible system: FAT16, FAT32

Output power: DC 5 V 500 mA

Playable bit rate: 64 kbps – 192 kbps

iPod/iPhone/iPad

Output power: iPod/iPhone: DC 5 V 1 A

iPad: DC 5 V 2.1 A

Video out: Composite

Speaker (SP-UXVJ5-W/SP-UXVJ5-V/SP-UXVJ5-G/

SP-UXVJ5-P/SP-UXVJ5-B/SP-UXVJ5-T)

Speaker type: Full Range Labyrinth Type

Speakers:

Woofer: 10 cm (3-15/16”) cone x 1

Power handling capacity: 15 W

Impedance: 6 Ω

Frequency range: 73 Hz to 18 000 Hz

Sound pressure level: 83 dB/W•m

Dimensions (approx.) (W x H x D):

115 mm × 186.5 mm × 162 mm (4-9/16” x 7-3/8” x 6-3/8”)

Mass (approx.): 0.7 k (1.6 lbs) eachg

Design and specifications are subject to change without notice.

Rating label is placed on the exterior of the bottom.

•

Precautions

Specifications

Getting started

Lithium coin

battery

(product number:

CR2025)

Prepare the remote control

When you use the remote control for the first time,

pull out the insulation sheet.

To replace the battery in the remote control

NOTES:

Store the battery in a place where children cannot

reach. If a child accidentally swallows the battery,

consult a doctor immediately.

To prevent the battery from overheating, cracking,

or starting a fire:

Do not recharge, short, disassemble or heat the

battery or dispose of it in a fire.

Do not leave the battery with other metallic

materials.

Wrap the battery with tape and insulate when

throwing away or saving it.

Do not poke the battery with tweezers or similar

tools.

Dispose of battery in the proper manner, according

to federal, state, and local regulations.

The battery (battery pack or battery installed) shall

not be exposed to excessive heat source such as

sunshine, fire or the like.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

•

−

•

Connections

4 To connect the FM/AM antenna

5 To connect the power cord

Do not use another AC adaptor to connect this model.

Do not connect the AC power cord to a wall outlet

before replacing the terminal cover.

•

FM antenna (supplied)

Extend it in order to obtain the best

reception.

For better FM reception,

disconnect the supplied FM

antenna, and connect to an outdoor

FM antenna (not supplied) using

a 75 Ω wire with a coaxial type

connector (IEC or DIN45325).

•

AM loop antenna

(supplied)

1 To connect a computer

2 To connect the monitor

Connect the video cord to view video/picture from the

iPod/iPhone/iPad on the monitor.

3 To connect the speakers and subwoofer

For installing the speakers, see “Notes on installing

speakers.”

•

From right

speaker

From left

speaker

RCA pin plug cord

(not supplied)

To the input of the

subwoofer

Composite video cord

(not supplied)

To the composite

video input of

monitor

USB cable (not

supplied)

To the USB port

of the computer

To a wall outlet

AC adaptor (supplied)

AC power cord (supplied)

NOTES:

Make sure the antenna conductors do not touch any

other terminals, connecting cords or the power cord.

Also, keep the antennas away from metallic parts

of the System, connecting cords, and the AC power

cord. Otherwise, it could cause poor reception.

DO NOT connect any other speakers than those

supplied.

•

1 Remove the terminal cover on the rear panel.

2 Connect the antennas and cords.

3 Arrange the cords, then replace the terminal cover.

Make sure that no cords are caught in the terminal

cover.

4 Connect the AC power cord to a wall outlet.

•

Turn the AM loop antenna (supplied) until the

best reception is obtained.

Keep the AM loop antenna cable wrapped

around the AM loop antenna frame, otherwise

the effectiveness and sensitivity of the AM loop

antenna may be reduced.

•

Supplied accessories

Remote control (× 1)

Lithium coin battery CR2025 (× 1)

The battery has been installed in the remote

control when shipped from the factory.

AC adaptor (AA-R1904) (× 1)

AC power cord (× 1)

AM loop antenna (× 1)

FM antenna (× 1)

Core filter (× 6)

(For UX-VJ3 USA and Canadian models: × 5)

AC plug adapter (× 1) (Not supplied for USA,

Canadian, European, Australian and Saudi Arabian

models)

If anything is missing, consult your dealer

immediately.

•

−

•

LOOP

75Ω

6Ω 16Ω

COAXIAL

ANTENNA

DC IN

19V 3.37A

RIG HT

SPEAKERS

LEFT

SUBWOOFER

OUT

VIDEO

OUT

PC I N

CAUT ION:

SEE BOT TOM

Settings and adjustments

Sleep Timer

Specify the time (in minutes.)

The display dims when the Sleep Timer is activated.

To check the remaining time until the System shuts off,

press once.SLEEP

Wake up Timer

By using Wake up Timer, you can wake up with your

favorite music.

Wake up Timer cannot be used if the clock has not been

set.

Tune into a station, insert a disc, or connect a USB

mass storage class device/iPod/iPhone/iPad/external

component to the System beforehand.

1 Display the timer contents setting screen.

Press the button repeatedly until the on-time setting

(“ON” and time indication) appears on the display.

2 Set the timer contents.

Hour and minute for the on-time (“ON”) and off-time

(“OFF”)

Frequency of use

“DAILY”: Activates the timer every day.

“ONCE”: Activates the timer once only.

Playback source

Volume

If you select “VOL – –,” the volume is set to the same

level as when the System was last turned off.

To correct a misentry during the process, press

MENU/CANCEL (for UX-VJ3 USA and Canadian

models: press CANCEL). You can return to the

previous step.

To exit from Wake up Timer setting, press CLOCK/

TIMER repeatedly as required.

•

−

•

−

•

Timer settings

3 Display timer standby setting screen.

“ON>SET” and “CANCEL” are displayed alternately.

4 Activate the Wake up Timer.

The settings you have made are shown on the display.

5 Turn off the System.

While the Wake up Timer is activated, the STANDBY/

TIMER lamp lights in orange.

To cancel the Wake up Timer, press CLOCK/TIMER

repeatedly until “ON>SET” and “CANCEL” alternate on the

display, then press (for UX-VJ3 USA and MENU/CANCEL

Canadian models: press ). “TIMER OFF” appears CANCEL

on the display.

Auto Power Save (APS)

You can turn off the System automatically to save power.

If one of the following conditions continues for

29 minutes, the System is turned off to save power:

The volume is set to “0” or muting is activated.

Slide door is open with “CD” selected as the source.

Disc/USB playback is stopped.

No disc is inserted, or no USB mass storage class

device, iPod/iPhone, or iPad is connected with the

target source selected.

“APS” appears on the display for about 2 seconds every

1 minute after one of the above conditions occurs. Then

it starts flashing about 30 seconds before the System

turns off.

•

−

(Canceled)

(Activated) (Canceled)

Setting the clock

1 Display the clock setting screen.

The hour indication flashes on the display.

If you have already set the clock before, press CLOCK/

TIMER until the hour indication flashes on the display.

2 Adjust the hour and minute.

To go back to the previous step, press MENU/

CANCEL (for UX-VJ3 USA and Canadian models: press

CANCEL).

The clock may gain or lose 1 to 2 minutes per month.

You may need to readjust the clock periodically.

To display the clock

While the System is turned on: press DISPLAY

repeatedly.

While the System is on standby: press 7.

Display settings

Display/illumination brightness

You can dim the display window and illumination.

Display information

You can change the information shown on the display.

Each time you press DISPLAY, the information shown on

the display changes.

The information shown on the display differs depending

on the source.

Tag information is shown on the display while an MP3/

WMA file is played back.

•

Sound adjustments

Sound Turbo

To emphasize the sound

Hyper Bass Sound (HBS)

To reinforce the bass sound

HBS setting is ineffective if Sound Turbo is activated.

Sound Mode

To select the sound mode suitable for your favorite music

Surround Mode

To activate surround mode

(Canceled)

(Activated) (Canceled)

(Canceled)

(Activated) (Canceled)

(Activated)

Do not connect the AC power cord until all other connections have been made.

(Only for

UX-VJ5)

Using the core filter

To reduce interference, be sure to attach the supplied

core filter to the power cord.

Run the cable through the core filter, and wind it firmly

3 times inside. Close the core filter until it clicks shut.

CAUTION: Do not damage the cord by applying

expressive force when winding.

•

DC power cord (from AC adaptor)

10 cm

(3-15/16”)

Black

Produkt Specifikationer

Mærke:	JVC
Kategori:	Højttaler
Model:	UX-VJ3
Vægt:	3100 g
Produktfarve:	Lyserød
Wi-Fi:	Ingen
Bluetooth:	Ingen
FM radio:	Ja
Udgangseffekt (RMS):	30 W
Antal USB 2.0-porte:	1
Dimensioner (BxDxH):	290 x 155 x 186.5 mm
Fjernbetjening inkluderet:	Ja
Frekvensområde:	- Hz
Lyd-output kanaler:	2.0 kanaler
Strømkilde type:	Vekselstrøm
Kampatibilitet med Apple-docking:	iPad, iPhone, iPod
Antal forudindstillede stationer:	30