Kyoritsu KEW Snap 2031 Manual

Kyoritsu Multimeter KEW Snap 2031

Læs nedenfor 📖 manual på dansk for Kyoritsu KEW Snap 2031 (2 sider) i kategorien Multimeter. Denne guide var nyttig for 35 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

INSTRUCTIONMANUAL

DIGITALACCLAMPMETER

KEW SNAP 2031

Jaw Trigger Range Switch

Data Hold Button

Transformer Jaws Display

Barrier

：

Itisapartprovidingprotectionagainstelectricalshockand

ensuringtheminimumrequiredairandcreepagedistances.

KEW SNAP

１．SAFETY WARNINGS

○

This instrument has been designed and tested according to IEC

Publication 61010-1, Safety Requirements for Electronic Measuring

Apparatus. This instruction manual contains warnings and safety rules

which must be observed by the user to ensure safe operation of the

instrument and retainitin safe condition. Therefore, read through these

operatinginstructionsbeforeusingtheinstrument.



# WARNING

●

Readthroughandunderstandinstructionscontainedinthismanual

beforestartingusingtheinstrument.

●

Keepthemanualhandytoquickreferencewhenevernecessary.

●

Besuretousetheinstrumentinitsintendedapplicationsonlyand

tofollowmeasurementproceduresdescribedinthemanual.

●

Besuretounderstandandfollowallsafetyinstructionscontained

inthemanual.

Failuretofollowtheaboveinstructionsmaycauseinjury,

instrumentdamageand/ordamagetoequipmentundertest.

Kyoritsuisbynomeansliableforanydamageresultingfromthe

instrumentincontradictiontothiscautionarynote.

○

Thesymbol

indicatedonthe instrumentmeansthattheuser must

refer to related parts in the manual for safe operation of the

instrument.  Be sure to carefully read instructionsfollowingeach



symbolinthismanual.

DANGER

：

Conditions and actions that are likely to cause

seriousorfatalinjury.

WARNING

：

Conditionsandactionsthatcouldcauseseriousor

fatalinjury.

CAUTION

：

Conditions and actions that could cause minor

injuryorinstrumentdamage.

Followingsymbolsareusedontheinstrumentandintheinstructionmanual.

Attentionshouldbepaidtoeachsymboltoensureyoursafety.

Refertotheinstructionsinthemanual.

Indicatesaninstrumentwithdoubleorreinforcedinsulation.

Indicates that this instrument can clamp on bare conductors when

measuring a voltage corresponding to the applicable Measurement

category,whichismarkednexttothissymbol.

IndicatesAC(AlternatingCurrent).

Earth

ThisinstrumentsatisfiesthemarkingrequirementdefinedintheWEEE

Directive(2002/96/EC). Thissymbol indicates separatecollection for

electricalandelectronicequipment.

DANGER

●

Never make measurement on a circuit above 300V AC. The

instrument is designed for measurement on a low-voltage circuit

below300VAC.

●

Donotattempttomakemeasurementinanexplosiveatmosphere

（

i.e.inthepresenceofflammablegassesorfumes,vaporordust

）

●

The transformer jaws are made of metal and their tips are not

insulated. Be especially careful about the hazard of possible

shortingwhereequipmentundertesthasexposedconductiveparts.

●

Neverattempttousetheinstrumentiftheinstrumentoryourhand

iswet.

●

Do not exceed the maximum allowable input value of any

measurementrange.

●

Never open the battery compartment cover when making

measurement.



●

Nevertrytomakemeasurementifanyabnormalconditions,such

asbrokenTransformerjawsorcaseisnoted.



●

The instrument is to be used only in its intended applications or

conditions.



Otherwise,safetyfunctionsequippedwiththeinstrumentdoesn



twork,

andinstrumentdamageorseriouspersonalinjurymaybecaused.

WARNING

●

Neverattempttomakeanymeasurementiftheinstrumtenthasany

structural abnormality such as cracked case and exposed metal

part.

●

Do not install substitute parts or make any modification to the

instrument.ReturntheinstrumenttoKyoritsuoryourdistributorfor

serviceandrepairtoensurethatsafetyfeaturesaremaintained.

●

Always switch off the instrument before opening the battery

compartmentcoverforbatteryreplacement.

CAUTION

●

Makesure that the range switch is set toan appropriate position

beforemakingmeasurement.

●

Be sure to set the range switch to the OFF position after use.

Whenthe instrument will not be in use for a long period of time,

placeitinstorageafterremovingthebatteries.

●

Do not expose the instrument to the direct sun, extreme

temperaturesordewfall.

●

Useadampclothanddetergentforcleaningtheinstrument.Donot

useabrasivesorsolvents.

○Measurement Category



To ensure safe operation of measuring instruments, IEC 61010

establishes safety standards for various electrical environments,

categorizedasOtoCATIV,andcalledmeasurementcategories.Higher-

numbered categories correspond to electrical environments with greater

momentary energy, so a measuring instrument designed for CAT III

environments can endure greater momentary energy than one designed

forCATII.



O :Circuits which are not directly connected to the mains power

supply.



CATII :Electrical circuits of equipment connected to an AC electrical

outletbyapowercord.



CATIII :Primaryelectricalcircuitsoftheequipmentconnecteddirectlyto

thedistributionpanel,andfeedersfromthedistributionpanelto

outlets.



CATIV :The circuit from the service drop to the service entrance, and

to the power meter and primary over-current protection device

(distributionpanel).

O: Device which is

not directly

connected to the

mains power supply

２．FEATURES

①

Pocket-size,miniatureACclampmeter

②

Teardropshapedjawsforeaseofuseincrowdedcableareasandother

tightplaces

③

DesignedtointernationalsafetystandardIEC61010-1

（

CAT

Ⅲ

300V

）

④

Awiderangeoffrequencyresponsefrom40Hzto1kHz

⑤

Dataholdfunctiontoallowforeasyreadingsindimlylightorhard-to-read

locations

⑥

Auto-power-offfunctiontoconservebatterypower

３．SPECIFICATIONS

Range

20A

200A

Accuracy

〜

19.99

Ａ

〜

199.9

Ａ

2.0%rdg

5dgt

（

50Hz

〜

1kHz

）

2.0%rdg

5dgt

（

･

60Hz

）

3.0%rdg

10dgt

（

40Hz

〜

1kHz

）

OperatingSystem Dualintegration

Display Fieldeffectliquidcrystaldisplay

MeasuringRanges 20A/200AAC

LowBatteryIndicatio "BATT"symbolappearsonthe

display

OverrangeIndication "1"flashesonthehighestdigit

ResponseTime Approx.1second

AutoPowerOff Theinstrumentautomaticallyshuts

offapprox.10minutesafterbeing

turnedon.

DataHold Forallranges

Locationforuse Indooruse,Altitudeupto2000m

StorageTemperature&Humidity -10

〜

℃

,relativehumidityupto

％



（

withoutcondensation

）

OperatingTemperature&Humidity 0

〜

℃

,relativehumidityupto

％



（

withoutcondensation

）



ConductorSize Approx.24mmindiameter

SafetyStandard IEC61010-1CAT

Ⅲ

300V

 IEC61010-2-032

EMC EN61326-1

RoHS EN50581

Dimension 147

（

）×

（

）×

（

）

Weight Approx.100g

（

batteryincluded

）



PowerSource TwoLR-44

（

）

orSR-44batteries

BatteryLife Approx.100hoursincontinuous

use

CurrentConsumption Approx.

１

Accessories InstructionManual

 TwoLR-44batteries

 CarryingCaseModel9090

４．OPERATlNG INSTRUCTIONS

４−１Battery Check

①

Settherangeswitchto20Aor200A

②

Ifthe display is clearwithout showing symbol "BATT",battery voltageis

OK.

③

If the display remains blank or symbol "BATT" appears, replace the

batteriesin accordancewith thebattery replacement procedures as

outlinedinsection5.

４−２AC Current Measurement

# CAUTION

●

The maximum size conductor to be tested is approx. 24 mm in

diameter. An accurate measurement cannot be made when the

transformer jaws are not fully closed on a conductor larger than

24mm.

●

When measuring a large current, the transformer jaws may buzz.

Thisisnotafaultanddoesnotaffecttheaccuracy.

●

About10minutesaftertheinstrumentisturnedon,theAutoPower

Off function turns the instrument off even during current

measurement.Tocontinue measurement,turn therange switch to

OFF,thento20Aor200Aagain.

# DANGER

●

Neverusetheinstrumentonacircuitabove300VAC.

●

The transformer jaws are made of metal and their tips are not

insulated. Be especially careful about the hazard of possible

shortingwhereequipmentundertesthasexposedconductiveparts.

●

Donotattempttomakemeasurementwiththebatterycompartment

coverremovedfromtheinstrument.

●

Keep your fingers and hands behind the barrier during

measurement.

①

Settherangeswitchto20Aor200A.

②

Pressthejawtriggertoopenthetransformerjawsandclampontoone

conductor only.  Try to place the conductor at the center of the

transformerjaws.

Correct Wrong

４−３Using Data Hold Function

①

PresstheDataHoldbuttontofreezethereading.Symbol"H"isdisplayed

toindicatetheinstrumentbeingintheDataHoldmode.

②

Press the button again to cancel the Data Hold mode.  The Data Hold

function is available on both 20A and 200A ranges for measurement in

hard-to-readlocations.

５．BATTERY REPLACEMENT

Whenthedisplayremainsblankorsymbol"BATT"appears,replacethe

batteries.

# DANGER

Neverreplacethebatterieswhilemakingmeasurement.

①

SettherangeswitchtotheOFFposition.

②

Press in the hole on the battery compartment cover with the tip of a

pointedobject,thenslideopenthecover.

③

Replacethebatterieswithnewones,observingcorrectpolarity.

ReplacementbatteriesshouldbetypeLR-44orSR-44.

＊

Theinstrumentdoesnotoperateifthepolarityissetreversely.

④

Slidethebatterycompartmentcoverinplace.

Kyoritsureservestherightstochangespecificationsordesigns

describedinthismanualwithoutnoticeandwithoutobligations.

4-19

DISTRIBUTOR

92-1354H

Produkt Specifikationer

Mærke:	Kyoritsu
Kategori:	Multimeter
Model:	KEW Snap 2031

Har du brug for hjælp?

Hvis du har brug for hjælp til Kyoritsu KEW Snap 2031 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Multimeter Kyoritsu Manualer

Kyoritsu KEW-2046R Manual

14 December 2024

Kyoritsu KEW 6010B Manual

14 December 2024

Kyoritsu KEW 2433R Manual

16 November 2024

Kyoritsu KEW 2432 Manual

16 November 2024

Kyoritsu KEW2046R Manual

20 September 2024

Kyoritsu KEW 2510 Manual

29 August 2024

Kyoritsu KEW 2500 Manual

29 August 2024

Kyoritsu KEW 2413R Manual

29 August 2024

Kyoritsu KT 200 Manual

29 August 2024

Kyoritsu 2431 Manual

29 August 2024

Multimeter Manualer

Nyeste Multimeter Manualer

21 December 2024

18 December 2024

16 December 2024

15 December 2024

15 December 2024

Vimar 14433.SL Manual

15 December 2024

Abus AirSecure CO2WM110 Manual

9 December 2024

Sanwa ACS101 Manual

8 December 2024

Sanwa TA55 Manual

8 December 2024

Sanwa SP20 Manual

8 December 2024