Optex OA-Flex Lite Manual
Optex
Dør / vindue sensor
OA-Flex Lite
Læs nedenfor 📖 manual på dansk for Optex OA-Flex Lite (2 sider) i kategorien Dør / vindue sensor. Denne guide var nyttig for 44 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
OA-FLEX LITE
ENGLISH
5933110 NOV 2022
Manufacturer's statement
Read this operation manual carefully before use to ensure proper operation of this product.
Failure to read this operation manual may cause improper operation and may result in serious injury or death of a person.
The meanings of the symbols are as follows.
1. This product is a non-contact switch intended for header mount or wall mount for use on an automatic
sliding door. Do not use for any other applications.
2. When setting the sensor's detection area, make sure that there is no traffic around the installation site.
3. Before turning the power ON, check the wiring to prevent damage or malfunction of equipment
connected to the product.
4. Only use the product as specified in the operation manual provided.
5. Be sure to install and adjust the sensor in accordance with the local laws and standards of the country
in which the product is installed.
6. Before leaving the installation site make sure that the product is operating properly and instruct the
building owner/operator on proper operation of the door and the product.
7. The product settings can only be changed by an installer or service engineer.
When changed, the changed settings and the date shall be registered in the maintenance logbook
accompanying the door.
NOTE
Failure to follow the instructions that accompany this indication and improper handling
may result in serious injury or death.
WARNING
Failure to follow the instructions that accompany this indication and improper handling
may result in injury and/or damage to property.
CAUTION
Pay special attention to sections with this symbol.
NOTE
Do not wash, disassemble,
rebuild or repair the sensor,
otherwise it may cause electric
shock or breakdown of the
equipment.
Danger of electric shock
WARNING
The following conditions are not suitable for sensor installation.
Fog,
Exhaust Wet Vibration Objects Reflection
Specifications
1000 ms 1000 ms
Signal saturation
Sensitivity too low
Slow Green blinking
Fast Green blinking
Operation indicator table
Status Operation indicator color
Stand-by Green
3rd - 5th row detection Orange
2nd row detection Red
1st row detection Red blinking
*1 :
When using this sensor, the sensor has to be connected to a door system which has the SELV circuit.
*2 : Overcurrent protection with less than 2A.
The specifications herein are subject to change without prior notice due to improvements.
NOTE
(1) Connector
(2) Mounting holes
(3) Operation indicator
(4) Dipswitches
(5) Area angle adjustment screws
(6) Area width adjustment screws
(7) Detection window
(8) Area adjustment tool
Dimensions and part names
245(9 5/8") 37(1 7/16")
7.5(5/16")
68(2 11/16")
36(1 7/16") 43(1 11/16")
125(4 15/16")
[mm (inch)]
(1) (2)
(3) (6)(5)(4) (7)
(8)
Charts show the values in the following area angle adjustment settings.
: Emitting spots
: Detection area
: Emitting spots
(can be eliminated)
Detection area
The actual detection area may become smaller
depending on the ambient light, the color/material of the
object or the floor as well as the entry speed of the
object.
The sensor may not be activated when the entering
speed of the object or a person is slower than 50 mm/s
or faster than 1500 mm/s.
NOTE
G
BC
DEF
H
I
J
1st row
2nd row
3rd row
4th row
5th row
A
Depth
Width
: 2°
: 0°
0.07 (3")
0.06 (2")
0.07 (3")
0.06 (2")
0.14 (6") 0.14 (6") 0.14 (6") 0
0
0
0
0
0
0
Installation
X
H
Y
Sensor
Door
Header
Floor
a. Place the mounting template at the desired mounting position.
(When setting the detection area close to the door, mount the sensor according to the chart below.)
b. Drill two mounting holes of ø3.4 mm (ø1/8").
c. To pass the cable through the header, drill a wiring hole of ø8 mm (ø5/16").
d. Remove the mounting template.
e. Remove the housing cover. Fix the sensor to the mounting surface with the two mounting screws.
1. Mounting
H : Height from the floor to the bottom of the header
(The mounting height is " + ".)H Y
Y : Distance between the bottom of the header and the sensor
X : Distance between the door and the mounting surface
Make sure not to mount the sensor lower than the bottom of header.
NOTE
CAUTION Risk of getting caught
Make sure to affix the mounting template as described in the above chart, otherwise it can be dangerous since there
may be no detection area around the threshold. Install the sensor as low as possible on the header.
Maximum mounting distance ( )Y
X2.00 (6'7")
0
0.05 (2")
0.10 (4") 0.11 (4") 0.11 (4")
0.15 (6") 0.10 (4")
0.20 (8")
0.25 (10")
0.30 (12")
H
0.13 (5")
2.50 (8'2")
0.13 (5")
0.10 (4")
0.09 (4")
[m (feet,inch)]
2.30 (7'7")
0.13 (5")
0.11 (4")
0.10 (4")
0.09 (4")
0.07 (3")
0.06 (2")
0.09 (4")
Make sure to connect the cable correctly to the door controller before turning the power ON.
When turning the power ON or after adjusting the settings, do not enter the detection area for more
than 10 s in order to enable the presence detection. Do not touch the dipswitches before turning the
power ON, otherwise an error occurs.
a. Plug the connector.
b. Supply power to the sensor. Adjust the detection area and set the dipswitches.
(See )Adjustments 3. Dipswitch settings
3. Turn ON the power
NOTE
Knockout
Do not use the sensor without the cover. When using the cable knockout,
install the sensor indoors or use the rain cover (Separately available)
otherwise electric shock or breakdown of the sensor may occur.
WARNING Danger of electric shock
Place the housing cover. If wiring is to be exposed, break the knockout.
4. Mounting the housing cover
Motion detection
Motion/Presence
detection
Mounting
surface
[m(feet,inch)]
Emitting area
3.00 (9'10")
2. Wiring
Wire the cable to the door controller.
Before starting the procedure, make sure that the power is turned OFF.
When passing the cable through the hole, do not tear the shield otherwise it may cause electric shock or breakdown
of the sensor.
Danger of electric shock
WARNING
Model
Cover color
Mounting height
Detection area
Detection method
Area angle adjustment
Power supply (*1)
Power consumption
Operation indicator
Output hold time
Response time
Operating temperature
Operating humidity
Noise level
Output
IP rate
Weight
Accessories
: OA-FLEX LITE
: Silver/Black
: 2.0 to 3.0 m (6'7" to 9'10")
: See Detection area
: Active infrared reflection
: Depth : -6° to +10°
Width : ±7°
(2 clicks with 3.5°every click-Left/Right)
: 12 to 24 VAC ±10 % (50/60 Hz)
12 to 30 VDC ±10 %
: < 2.0 W (< 5 VA at AC)
: See Operation indicator table
: Approx. 500 ms
: < 300 ms
: -20 to +55°C (-4 to 131°F)
: < 80 %(non-condensing)
: < 70 dBA
: Form C relay 50 V 0.3 A Max.
(Resistance load)
: IP54
: 220 g (7.8 oz)
: 1 Quick Guide
2 Mounting screws
1 Mounting template
1 Area adjustment tool
1 Cable 3 m (9'10")(*2)
Sensor
Power
Power
COM.
N.O.
N.C.
Grey
Grey
White
Yellow
Green
B
C
D
E
F
G
H
I
J
A 2.00 (6'7") 2.30 (7'7") 2.50 (8'2") 3.00 (9'10")
0.26 0.30 (1
'
1
")
(10
")
(1
')
0.33 (1
'
4
")
0.39
0.53 0.61 (2
'
2
")
(1
'
9
")
(2
')
0.66 (2
'
7
")
0.79
0.80 0.92 (3
'
3
")
(2
'
8
")
(3
')
1.00 (3
'
11
")
1.20
1.14 1.32 (4
'
8
")
(3
'
9
")
(4
'
4
")
1.43 (5
'
8
")
1.72
1.53 1.76 (6
'
3
")
(5
')
(0
'5”)
(0
'6”)
(0
'6”)
(0
'8”)
(5
'
9
")
1.91 2.29 (7
'
6
")
0.96 1.10
(3
'
11
")
(3
'
7
")
1.20 (4
'
9
")
1.44(3
'
2
")
1.55 1.78 (6
'4")
(5
'1")
(5
'10")
1.93 (7
'7")
2.32
2.13 2.45 (8
'
9
")
(7
')
(8
')
2.66 (10
'
6
")
3.20
0.15 0.16 0.190.13
Produkt Specifikationer
| Mærke: | Optex |
| Kategori: | Dør / vindue sensor |
| Model: | OA-Flex Lite |
Har du brug for hjælp?
Hvis du har brug for hjælp til Optex OA-Flex Lite stil et spørgsmål nedenfor, og andre brugere vil svare dig
Dør / vindue sensor Optex Manualer
14 November 2024
14 November 2024
18 April 2024
30 Juli 2023
29 Juli 2023
18 April 2023
16 Februar 2023
12 Februar 2023
26 Januar 2023
8 November 2022
Dør / vindue sensor Manualer
- Dør / vindue sensor Bosch
- Dør / vindue sensor Philips
- Dør / vindue sensor Nedis
- Dør / vindue sensor Abus
- Dør / vindue sensor Smartwares
- Dør / vindue sensor EZVIZ
- Dør / vindue sensor König
- Dør / vindue sensor Olympia
- Dør / vindue sensor Techly
- Dør / vindue sensor Marmitek
- Dør / vindue sensor Chamberlain
- Dør / vindue sensor Devolo
- Dør / vindue sensor Pentatech
- Dør / vindue sensor Axis
- Dør / vindue sensor Kidde
- Dør / vindue sensor Schwaiger
- Dør / vindue sensor Steren
- Dør / vindue sensor Setti+
Nyeste Dør / vindue sensor Manualer
24 November 2024
6 Oktober 2024
13 September 2024
12 September 2024
27 Juli 2024
19 Juni 2024
5 Juni 2024
24 Maj 2024
30 Januar 2024
6 September 2023