Optex OM-106C Manual
Optex
Dør / vindue sensor
OM-106C
Læs nedenfor 📖 manual på dansk for Optex OM-106C (1 sider) i kategorien Dør / vindue sensor. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
5916154 OCT 2019
OM-105C / 106C
Manufacturer's statement
Disregard of the warning symbol can cause improper operation which may cause death or
serious injury.
Special attention is required to the section of this symbol.
Disregard of the caution symbol can cause improper operation which may cause injury of a
person or damage the object.
Read this operation manual carefully before use to ensure proper operation of this product.
Failure to read this operation manual may cause improper operation and may result in serious injury or death of a person.
The meanings of the symbols are as follows.
1. This sensor is a non-contact switch intended for header mount/ceiling mount of an automatic door.
Do not use for any other applications.
2. When setting the sensor's detection area, make sure there is no traffic around the installation site.
3. Before turning the power on, check the wiring to prevent damage or malfunction of equipments that
are connected to the sensor.
4. Only use the sensor as specified in the operation manual provided.
5. Be sure to install the sensor in accordance with the local laws and standards of the country in which
the sensor is installed.
6. Before leaving the job site make sure that the sensor is operating properly and instruct the building
owner/operator on proper operation of the door and the sensor.
7. The sensor setting can only be changed by an installer or service engineer. When changed, register
the changed setting and dates in the maintenance logbook accompanying the door.
The following conditions are not suitable for the sensor
installation.
- Vibrating header or mounting surface.
- Waterdrops or snow on the sensor.
- Moving objects, steel plate, emergency lights or
illumination in the detection area or in vicinity.
30
30
1. Antenna
2. Sensitivity potentiometer
3. Mounting holes
4. Dipswitches
5. Wiring hole
6. Narrow lens
7. Operation indicator
8. Terminal block
9. Cover fixing
6*
1
2
3
4
3
8
5
7
131(5 3/16")
61(2 3/8")
55(2 3/16")
9
[mm(inch)]
* Narrow lens is stored
at the back of housing
cover.
97(3 13/16")
Outer dimensions and part names
Checking
Check the operation according to the chart below.
Sensor status
Green Red
Output contact
Stand-by
Operation indicator
Power OFF
OFF
Detection
Set-up
(Approx. 10 s)
Green blinking
Troubleshooting
Problem Operation
indicator Possible cause Possible countermeasures
Sensitivity is too high. Set the sensitivity lower.
Door opens
when no one is
in the detection
area.
(Ghosting)
Red
The detection area is overlaping with the
door.
Adjust the detection area away from the door.
Or set Dipswitch4 to ON.
Green
blinking
Door does not
open when a
person enters
the detection
area.
Green
None Wrong power supply voltage. Set to the stated voltage.
Unstable Check the wiring and Terminal block.Wrong wiring or connection failure.
Sensitivity is too low. Set the sensitivity higher.
Wrong detection area positioning. Check Adjustments.
The sensor is being set up. Wait for the set-up to complete.
Water drops on the housing cover. Wipe the housing cover with a cloth.
Wrong wiring or connection failure. Check the wiring and Terminal block.
Door remains
open Green
Set Dipswitch1 to ON.(OM-106C only)
Or Dipswitch4 to ON.
Raining or snowing.
Hereby, OPTEX declares that the radio equipment type OM-105C/106C series are in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address; www.optex.net
Manufacturer
5-8-12 Ogoto Otsu 520-0101, Japan
TEL.: +81(0)77 579 8700 FAX.: +81(0)77 579 7030
URL www.optex.net
OPTEX CO., LTD.
European Subsidiary
OPTEX Technologies B.V.
Henricuskade 17, 2497 NB The Hague, The Netherlands
TEL.: +31(0)70 419 41 00 FAX.: +31(0)70 317 73 21
E-MAIL: info@optex.eu URL www.optex.eu
North and South America Subsidiary
OPTEX INCORPORATED
18730 S. Wilmington Avenue, Suite 100
Rancho Dominguez CA 90220 U.S.A
TEL.: +1-800-877-6656 FAX.: +1(310)898-1098
URL www.ot-inc.com
East coast office
8510 McAlpines Park Drive, Suite 108 Charlotte,
NC 28211 U.S.A.
TEL.: +1-800-877-6656 FAX.: +1(704)365-0818
URL www.ot-inc.com
ENGLISH
WARNING
CAUTION
NOTE
NOTE
Do not wash, disassemble, rebuild or repair
the sensor, otherwise it may cause electric
shock or breakdown of the equipment.
Danger of electric shock
WARNING NOTE
* At the back of housing cover
Specifications
Model
Cover color
Mounting height
Detection method
Transmitter frequency
Transmitter radiated power
Detection area
Vertical adjustment
Horizontal adjustment
Power supply
Power consumption
Minimum speed
Operation indicator
: OM-105C / 106C
: Silver / Black
: 2.0 (6'7") to 3.5 m (11'5")
: Microwave doppler effect
: 24.125 GHz
: < 20 dBm
: See Detection area
: +10° to +70° (Header mount)
+20° to +80° (Ceiling mount)
: 30° to left or right
: 12 to 24 VAC(±10 %)
12 to 30 VDC(±10 %)
: < 1.5 W(< 2 VA at AC)
: 5 cm(1 15/16")/s
: Green / Stand-by
Red / Detection
Green blinking / Set-up
Output
Output hold time
Response time
Operating humidity
Operating temperature
IP rate
Weight
Accessories
: Form C relay
50 V 0.3 A Max.(Resistance load)
: 0.5 s/2.0 s
: < 0.3 s
: < 80 %
: -20°C to +55°C (-4°F to 131°F)
: IP54
: 140 g (4.9 oz)
: 1 Cable 3 m (9'10")
1 Operation manual
2 Mounting screws
1 Mounting template
1 Narrow lens*
The specifications herein are subject to change without prior notice due to improvements.
NOTE
31.Plug the connector of the sensor.
2.Supply power to the sensor and the sensor will automatically start the set-up mode with blinking Green.
3.Adjust the detection area and set the Dipswitches. (See ) Adjustments
Installation
2
11. Place the mounting template at the desired mounting position.
2. Drill 2 mounting holes of ø3.4 mm (ø1/8").
3. To pass the cable through to the header, drill a wiring hole of ø8 mm (ø5/16").
4. Remove the mounting template.
5. Remove the housing cover with screw driver as shown below.
Attach the sensor to the mounting surface with 2 mounting screws.
2
Open
1
Insert
Screw driver
Cover fixing
3
Slide
Screw driver
Wire the cable to the door controller properly as shown below.
Power supply
12 to 24 VAC ±10 %
12 to 30 VDC ±10 %
Relay
N.O.
N.C.
White
Brown
Green
Yellow
Before starting the procedure, ensure that the power is turned OFF.
When passing through the cable to the hole, make sure not to tear the shield,
otherwise it may cause electric shock or breakdown of the sensor.
4Hook the housing cover on the left side of main body to place the housing cover.
If wiring is to be exposed, break the knockout.
Make sure to connect the cable correctly to the door controller before turning the power ON.
The sensor does not detect objects for 10 s after supplying power.
Danger of electric shock
WARNING
Do not use the sensor without the housing cover. When using the cable
knockout, install the sensor indoors or use the rain-cover (Separately available)
otherwise electric shock or breakdown of the sensor may occur.
Danger of electric shock
WARNING
NOTE
1
Adjustments
Detection area angle adjustment
4
Detection area
2
Narrow area
3To obtain Narrow area, place Narrow lens attached at the back of housing cover.
To place Narrow lens, follow step1&2 as shown on the right.
Adjustment Scale Angle
Low High
Dipswitches settings
: Detection
: Non-Detection
Set Dipswitch1&2 to enable the direction recognition. (OM-106C only.)
Narrow area
H
M
L
Door
Detection
area
12
1 2
12
1 2
Bi-direction(Bi)
Bi-direction
Uni-direction(Uni)
Uni-direction with Auto
-caution mode*(ACM)
When Dipswitch1 is set to OFF,
Bi-direction mode is effective,
regardless of Dipswitch2 setting.
Dipswitch 3 : Output hold time Dipswitch 4 : Immunity
4
If there is external interference,
set Dipswich 4 to ON.
33
2.0 s0.5 s
2
1
Wide area
H
M
[mm(feet,inch)]
L
Mounting height:2.2 m(7'3")
Vertical adjustment : +34°
04000
(13′1")
4000
(13′1")
4000
(13′1")
1000
(3′3")
1000
(3′3")
1000
(3′3")
2000
(6′7")
2000
(6′7")
2000
(6′7")
3000
(9′10")
3000
(9′10")
3000
(9′10")
0
Adjust the detection area with Sensitivity potentiometer.
0 1000
(3′3")
1000
(3′3")
2000
(6′7")
2000
(6′7")
3000
(9′10")
3000
(9′10")
4000
(13′1")
1000
(3′3")
2000
(6′7")
3000
(9′10")
0
[mm(feet,inch)]
Mounting height:2.2 m(7'3")
Vertical adjustment : +34°
When the sensor is mounted at higher than 3.0 m, set the Sensitivity to "H"(High).
Do not touch electric part of the sensor to avoid possible breakdown of the sensor.
30
30
30
Vertical
adjustment
Horizontal
adjustment
Side viewFront view
Front view Front view
Side view
+70
+10
+20
+80
Header Ceiling
+30+30
0
30
30
5º X 12 steps
3º X 20 steps
*Auto-caution mode
(
A person wavering in
the detection area to
be detected.)
Front view
10° 10°10° 10°
43° 43°
CAUTION
1. Always keep the housing cover clean. If dirty, wipe the housing cover lightly with a cloth.
(Do not use any cleaner or solvent.)
2. Do not wash the sensor with water.
3. Do not disassemble, rebuild or repair the sensor yourself, otherwise electric shock may occur.
4. Always contact your installer or service engineer when changing the settings.
5. Do not paint the housing cover.
1. When turning the power ON, always walk-test the detection area to ensure proper operation.
2. Do not place any objects that move or emit light in the detection area. (e.g. Plant, illumination, etc.)
Inform building owner/operator of the following items
WARNING
NOTE
NOTE
Produkt Specifikationer
| Mærke: | Optex |
| Kategori: | Dør / vindue sensor |
| Model: | OM-106C |
Har du brug for hjælp?
Hvis du har brug for hjælp til Optex OM-106C stil et spørgsmål nedenfor, og andre brugere vil svare dig
Dør / vindue sensor Optex Manualer
14 November 2024
14 November 2024
18 April 2024
30 Juli 2023
29 Juli 2023
18 April 2023
16 Februar 2023
12 Februar 2023
26 Januar 2023
8 November 2022
Dør / vindue sensor Manualer
- Dør / vindue sensor Bosch
- Dør / vindue sensor Philips
- Dør / vindue sensor Nedis
- Dør / vindue sensor Abus
- Dør / vindue sensor Smartwares
- Dør / vindue sensor EZVIZ
- Dør / vindue sensor König
- Dør / vindue sensor Olympia
- Dør / vindue sensor Techly
- Dør / vindue sensor Marmitek
- Dør / vindue sensor Chamberlain
- Dør / vindue sensor Devolo
- Dør / vindue sensor Pentatech
- Dør / vindue sensor Axis
- Dør / vindue sensor Kidde
- Dør / vindue sensor Schwaiger
- Dør / vindue sensor Steren
- Dør / vindue sensor Setti+
Nyeste Dør / vindue sensor Manualer
24 November 2024
6 Oktober 2024
13 September 2024
12 September 2024
27 Juli 2024
19 Juni 2024
5 Juni 2024
24 Maj 2024
30 Januar 2024
6 September 2023