Ozito PXCLMK-1318EU Manual

Ozito Plæneklipper PXCLMK-1318EU

Læs nedenfor 📖 manual på dansk for Ozito PXCLMK-1318EU (3 sider) i kategorien Plæneklipper. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

CORDLESS LAWN

MOWER KIT

ORIGINAL INSTRUCTIONS

SPECIFICATIONS

Voltage: 18V

Cutting Diameter: 300mm

Cutting Heights: 30, 50 & 70mm

No Load Speed: 3,300/min

Grass Catcher: 25 litres

Weight (Tool Only): 8.57kg

PXCLMK-1318EU

Cordless Lawn Mower

ozito-diy.co.uk

Safety Key

1 x 3.0Ah Battery

1 x Eco Charger

WHAT’S IN THE BOX

DESCRIPTION OF SYMBOLS

TROUBLESHOOTING

WARRANTY

SPARE PARTS

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

1117

BATTERY AND CHARGER SAFETY WARNINGS

Removing and Fitting the Blade

Cleaning, Maintenance and Storage

1. To remove the blade screw, hold the blade rmly and

with a 13mm socket loosen the blade screw by turning

it anti-clockwise.

NOTE: A piece of timber will assist in holding the blade

while removing or tightening the blade bolt.

2. Remove the blade screw, washer and blade.

3. To t the blade, place the blade over the centre hole aligning the lugs.

4. Then retighten the fastening screw with the universal wrench. The tightening torque should be

approx. 25 Nm.

TIMBER

• Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe working condition.

• Check the catcher frequently for wear or deterioration.

• Replace worn or damaged parts for safety.

• Only use the replacement blade and blade bolt specied for this product.

• Be careful during adjustments of the lawn mower to prevent entrapment of the ngers between

moving blade and xed parts of the machine.

• When not in use, the mower should be stored in a dry, frost-free location, out of reach of

children. If the housing of the mower requires cleaning, do not use solvents but a moist soft

cloth and brush only.

• Frequently check the wheel threads are rm and tight.

Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the

lawn mower by an unauthorised person or by mishandling of the lawn mower. This tool is designed

for DIY use - use in commercial or industrial environments will void the warranty.

WARNING! ALWAYS ENSURE THE LAWN MOWER

BLADE HAS COMPLETELY STOPPED, REMOVE

SAFETY KEY, BATTERY AND GRASS CATCHER PRIOR

TO ANY MAINTENANCE.

CAUTION! ALWAYS USE GLOVES WHEN HANDLING

THE BLADE. SHARP EDGES COULD CAUSE INJURY.

Problem Cause Remedy

Mower is not

starting

Possible clogging Check underneath the mower and clear out

as necessary

Battery is low in charge Charge battery

Battery not inserted

properly

Insert battery pack correctly

Grass too long Raise the cutting height to reduce starting

load

Safety key not inserted

correctly

Fit correctly

Mower is

hard to push

Height of cut too low Raise cutting height

Cutting blade blunt Replace blade

Possible clogging Check underneath the mower and clear out

as necessary

Grass too long Raise the cutting height and walk slower

Grass too dense Raise the cutting height and walk slower and

cut more frequently

Wet grass Wait until the grass dries before mowing

Motor stops

while cutting

Height of cut too low Raise the cutting height

Battery has no power Charge battery

Mower is

not catching

grass properly

Height of cut too low Raise the cutting height

Wet grass Wait until the grass dries before mowing

Mower

vibrating

Bent or damaged blade Replace blade

Replace the metal blade after 50 hours mowing or 2 years whichever

is sooner. If the blade is cracked or damaged replace it with a new

one.

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectication of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

MAINTENANCE

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

WARNING! When using mains-powered tools, basic safety precautions, including

the following, should always be followed to reduce risk of ﬁre, electric shock, personal

injury and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the charger to the mains supply make sure that the data on the rating plate are identical to the mains data.

This tools charger is double insulated, therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for

added protection against injury resulting from a possible electrical insulation failure within the tool.

The power supply for this products charger should be protected by a residual current device (rated at 30mA or less). A residual current

device reduces the risk of electric shock.

This equipment is not designed to be used by people (including children) with limited physical, sensory or mental

capacities or those with no experience and/or knowledge unless they are supervised by a person who is responsible

for their safety or they have received instructions from such a person in how to use the equipment safely. Children must

always be supervised in order to ensure that they do not play with the equipment.

Safety instructions for hand mower

• Before use, check the mains cable and extension cable for signs of damage and aging.

• If the cable is damaged during operation, disconnect it immediately from the power supply.

• Check the machine for signs of damage before use. Repairs may only be carried out by our service workshop. If unusual

vibrations occur during use, switch the machine off immediately and pull the plug. Check the cutters and clean them if

necessary. If the machine continues to vibrate, switch it off, disconnect it from the mains supply and send it to our service

workshop.

• The machine must not be tipped whilst it is being started. Both hands must be on the handle when you start the

machine.

• Worn parts may only be replaced by our service workshop. If necessary contact the service address provided.

WARNINGS

• Do not touch the cutters until the machine has been disconnected from the mains and the cutters have reached a

complete standstill.

• Break the connection with the mains supply (in other words pull the plug out of the socket):

- whenever you leave the machine unattended;

- before released a blocked cutter;

- before inspecting or cleaning and before working on the machine;

- if a foreign body has been struck;

- whenever the machine starts to vibrate oddly.

• Carefully read the instructions for how to operate the machine safely.

Note

a) Read the directions with due care. Familiarize yourself with the operator controls and proper operation of the machine.

b) Never allow children or other persons who are not familiar with the operating instructions to use the mower. Contact

your local governmental agency for information regarding minimum age requirements for the user.

c) Never mow in the direct vicinity of persons - especially children - or animals.

d) Always keep in mind that the operator or user of the equipment is responsible for accidents involving other persons

and/or their property.

Preliminary measures

a) Always wear sturdy, non-slip footwear and long trousers when mowing. Never mow barefoot or in sandals.

b) Check the ground on which the equipment will be used and remove all objects that could be caught up or violently ung

out.

c) Before using the scythe, visually inspect it to ensure that the blade, mounting bolts and the entire cutting apparatus are

in good working order (i.e. not worn out or damaged). To prevent any imbalance, replace worn out or damaged blades

and mounting bolts as a set only (if applicable).

d) Remember that if the machine has several cutting tools, the movement of one cutting tool may result in the other cutting

tools starting to rotate.

Handling

a) Only mow in broad daylight or in well-lit conditions.

b) Do not use the machine on wet grass.

c) Always maintain good footing on inclines.

d) Only operate the machine at a walking pace.

e) Always mow across hills i.e. never straight up or straight down.

f) Be particularly careful when you change direction on a slope.

g) Do not mow on overly steep inclines.

h) Always be extra careful when turning the mower around and when pulling it towards you.

i) Switch the mower off , pull the plug and wait until the cutters have reached a complete standstill if you need to tip the

mower over, transport it over surfaces other than grass and if the mower has to be moved from and to the area you wish

to mow.

j) Never use the lawn mower if the guards are damaged or without the attached guards, e.g. deectors and/or grass

catching devices.

k) Use the ON/OFF switch carefully as described in the manufacturer’s instructions. Make sure that your feet are far

enough away from the mower blade!

l) The lawn mower should not be tilted when the motor is switch on unless it has to be raised for starting purposes. In this

case, tilt it as little as absolutely necessary and only raise the side opposite to that of the user.

m) Do not switch on the mower if you are positioned in front of the chute.

n) Never move your hands or feet toward or under any rotating parts. Keep clear of the chute opening at all times.

o) Never lift or carry a lawn mower with the engine running.

p) Switch off the motor and pull the power plug:

- before you dislodge any blockages or clogs in the chute.

- before carrying out any checks, cleaning, maintenance or other work on the lawn mower.

- if you have struck a foreign object. Examine the mower for signs of damage and carry out any necessary repairs

before restarting and continuing to work with the mower.

- if the lawn mower begins to experience exceptionally strong vibrations, immediately switch it off and check it.

q) Switch off the mower and pull the plug whenever you leave the mower.

Maintenance and storage

a) Make sure that all nuts, bolts and screws are tightened securely and that the machine is in safe working condition.

b) Allow the mower to cool before you put it into an enclosed area.

c) To avoid the risk of  re, keep the motor housing and ventilation slots clear of grass, leaves, oil and grease.

d) Routinely check the grass basket for signs of wear and impaired functionality.

e) For your own safety, have worn or damaged parts replaced without delay.

f) Take care not to jam your ngers between moving blades and stationary parts of the equipment while you are adjusting

the equipment.

g) While you are carrying out maintenance work on the blades, remember that the blades can still be moved even if the

power source has been switched off .

CAREFUL HANDLING AND USE OF CORDLESS EQUIPMENT

• Ensure that the equipment is switched off before you insert the battery. Inserting a battery into an electric tool that is

switched on can cause accidents.

• Only charge the batteries in chargers that are recommended by the manufacturer. A charger that is designed for a

certain type of batteries may pose a re risk if it is used with other types of batteries.

• Use only the correct batteries in the electric tools. The use of other batteries may result in injuries and a re risk.

• Keep unused batteries away from paper clips, coins, keys, nails, screws and other metallic objects that could cause a

short circuit between the contacts. A short circuit between the battery contacts may cause burns or a re.

• In case of incorrect use, uid may escape from the battery. Avoid contact with it. If you touch it by mistake, rinse the

affected area with water. If you get the uid in your eyes, also seek medical advice. Leaking battery uid can cause skin

irritation or burns.

Additional safety instructions

We pay a great deal of attention to the design of every battery pack to ensure that we supply you with batteries which

feature maximum power density, durability and safety. The battery cells have a wide range of safety devices. Each

individual cell is initially formatted and its electrical characteristic curves are recorded. These data are then used

exclusively to be able to assemble the best possible battery packs.

Despite all the safety precautions, caution must always be exercised when handling batteries. The following

points must be obeyed at all times to ensure safe use.

Safe use can only be guaranteed if undamaged cells are used. Incorrect handling can cause cell damage.

Important: Analyses conrm that incorrect use and poor care are the main causes of the damage caused by high

performance batteries.

Information about the battery

1. The battery pack supplied with your cordless tool is not charged. The battery pack has to be charged before

you use the tool for the rst time.

2. For optimum battery performance avoid low discharge cycles. Charge the battery pack frequently.

3. Store the battery pack in a cool place, ideally at 15°C and charged to at least 40%.

4. Lithium-ion batteries are subject to a natural ageing process. The battery pack must be replaced at the latest

when its capacity falls to just 80% of its capacity when new. Weakened cells in an aged battery pack are no

longer capable of meeting the high power requirements and therefore pose a safety risk.

5. Do not throw battery packs into an open re. There is a risk of explosion!

6. Do not ignite the battery pack or expose it to re.

7. Do not exhaustively discharge batteries. Exhaustive discharge will damage the battery cells. The most common

cause of exhaustive discharge is lengthy storage or non-use of partly discharged batteries. Stop working as

soon as the performance of the battery falls noticeably or the electronic protection system triggers. Place the

battery pack in storage only after it has been fully charged.

8. Protect batteries and the tool from overloads. Overloads will quickly result in overheating and cell damage

inside the battery housing without this overheating actually being apparent externally.

9. Avoid damage and shocks. Replace batteries which have been dropped from a height of more than one meter

or which have been exposed to violent shocks without delay, even if the housing of the battery pack appears to

be undamaged. The battery cells inside the battery may have suffered serious damage. In this respect, please

also read the waste disposal information.

10. If the battery pack suffers overloading and overheating, the integrated protective cut-off will switch off the

equipment for safety reasons. . Do not press the ON/OFF switch any more if the protective cut-off Important

has actuated. This may damage the battery pack.

11. Use only original battery packs. The use of other batteries may result in injuries, explosion and a re risk.

Information on chargers and the charging process

1. Please check the data marked on the rating plate of the battery charger. Be sure to connect the battery charger

to a power supply with the voltage marked on the rating plate. Never connect it to a different mains voltage.

2. Protect the battery charger and its cable from damage and sharp edges. Have damaged cables repaired

without delay by a qualied electrician.

3. Keep the battery charger, batteries and the cordless tool out of children’s reach.

4. Do not use damaged battery chargers.

5. Do not use the supplied battery charger to charge other cordless tools.

6. In heavy use the battery pack will become warm. Allow the battery pack to cool to room temperature before

commencing with the charging.

7. Do not over-charge batteries. Do not exceed the maximum charging times. These charging times only apply

to discharged batteries. Frequent insertion of a charged or partly charged battery pack will result in over-

charging and cell damage. Do not leave batteries in the charger for days on end.

8. Never use or charge batteries if you suspect that the last time they were charged was more than 12

months previously. There is a high probability that the battery pack has already suffered dangerous damage

(exhaustive discharge).

9. Charging batteries at a temperature below 10°C will cause chemical damage to the cell and may cause a re.

10. Do not use batteries which have heated during the charging process, as the battery cells may have suffered

dangerous damage.

11. Do not use batteries which have suffered curvature or deformation during the charging process or which show

other non-typical symptoms (gassing, hissing, cracking,…)

12. Never fully discharge the battery pack (recommended depth of discharge max. 80%) A complete discharge of

the battery pack will lead to premature ageing of the battery cells.

13. Never charge the batteries unsupervised.

Protection from environmental inuences

1. Wear suitable work clothes. Wear safety goggles.

2. Protect your cordless tool and the battery charger from moisture and rain. Moisture and rain can cause

dangerous cell damage.

3. Do not use the cordless tool or the battery charger near vapours and inammable liquids.

4. Use the battery charger and cordless tools only in dry conditions and an ambient temperature of 10-40°C.

5. Do not keep the battery charger in places where the temperature is liable to reach over 40°C. In particular, do

not leave the battery charger in a car that is parked in the sunshine.

6. Protect batteries from overheating. Overloads, over-charging and exposure to direct sunlight will result in

overheating and cell damage. Never charge or work with batteries which have been overheated – replace them

immediately if possible.

7. Storage of batteries, battery chargers and cordless tools. Store the charger and your cordless tool only in

dry places with an ambient temperature of 10-40°C. Store your lithium-ion battery pack in a cool, dry place at

a temperature of 10-20°C. Protect them from humidity and direct sunlight. Only place fully charged batteries in

storage (charged at least 40%).

8. Prevent the lithium-ion battery pack from freezing. Battery packs which were stored below 0°C for more than

60 minutes must be disposed of.

9. When handling batteries beware of electrostatic charge: Electrostatic discharges cause damage of the

electronic protection system and the battery cells. Avoid electrostatic charging and never touch the battery

poles

Rechargeable batteries and cordless electric machines and tools contain materials that are potentially harmful to

the environment. Never place any cordless electric machines or tools in your household refuse. When cordless

electric machines or tools become defective or worn, remove the rechargeable batteries and return them to

iSC GmbH (address: Eschenstrasse 6, D-94405, Germany). If the rechargeable batteries cannot be removed,

return the complete cordless machine or tool.

You can then be sure that the equipment will be correctly disposed of by the manufacturer.

When shipping or disposing of batteries and cordless tools, always ensure that they are packed

individually in plastic bags to prevent short circuits and res.

Do not lose these safety instructions.

Dispose of batteries correctly.

Guaranteed sound power

level: 92 dB.

Keep your distance.

Read the directions for use

before operating the

equipment.

Caution: Sharp blades! Pull out the safety plug before carrying

out any repair work or if the power cable is damaged.

The blades will continue to rotate after the motor is switched off.

Safety class II

Protect the equipment from

rain and damp conditions.

Store the battery only in dry rooms with an ambient temperature

of +10 c to +40 c. Place only charged batteriers in storage¼ ¼

(charged at least 40%).

TECHNICAL DATA

SERVICE INFORMATION

Category Example

Wear parts* Carbon brushes, Battery

Consumables Blade

Missing parts

Please note that the following parts of this product are subject to normal or natural wear and that

the following parts are therefore also required for use as consumables.

* Not necessarily included in the scope of delivery!

Sound power level LWA :................................89.3 dB(A)

Sound pressure level LPA

:.............................77.3 dB(A)

Uncertainty KPA :............................................3 dB(A)

Uncertainty KWA :............................................2.35 dB(A)

Guaranteed sound power level LWA :.............92(dB(A)

Vibration at the handlebars ah: .................. ≤ 2.5 m/s ²

Uncertainty K: ..............................................1.5m/s²

Protection type: ...........................................IPX1

Protection class: ..........................................III

Lithium-ion battery

Voltage: ...................................................... 18 V DC

Capacity: ......................................................3.0 Ah

Number of cells: .........................................10

Battery charger

Input voltage: ..............................................110-240 V~ 50-60 Hz, 21W

Output: ........................................................ 21 V DC, 800mA

Protection class:...........................................II

Caution!

The equipment and the charger are allowed to be used only for the lithium-ion batteries of the

Power-X-Change series!

Sound and vibration values were measured in accordance with the standards

EN ISO 3744:1995,

ISO 11094:1991 and EN ISO 20643:2008.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equip-

ment and its implementation in national laws, old electric power tools have to be separated

from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a

recycling depot.

Recycling alternative to the return request: As an alternative to returning the equipment to the

manufacturer, the owner of the electrical equipment must make sure that the equipment is

properly disposed of if p1-he no longer wants to keep the equipment. The old equipment can be

returned to a suitable collection point that will dispose of the equipment in accordance with

the national recycling and waste disposal regulations. This does not apply to any accessories or

aids without electrical components supplied with the old equipment.

This consignment contains lithium-ion batteries.

In accordance with special provision 188 this consignment is not subject to the ADR regula-

tions. Handle with care. Danger of ignition in case of damage to the consignment package. If

the consignment package is damaged: Check and if necessary repackage. For further informa-

tion contact: 0049 1807 10 20 20 66 (xed network 14 ct/min, mobile phone max. 42 ct/min)

Outside Germany charges will apply instead for a regular call to a landline number in Germany.

Declaration of Conformity

Gao/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Cordless Lawn Mower PXCLMS-118U / Eco Charger PXCG-120U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X 2011/65/EU

X 2006/42/EC

Annex IV

Notied Body:

Notied Body No.:

Reg. No.:

X 2000/14/EC_2005/88/EC

Annex V

X Annex VI

Noise: measured L

= 89,3 dB (A); guaranteed L

WA = 92 dB (A)

P = KW; L/Ø = 30 cm

Notied Body: TÜV Süd Industrie Service GmbH (NB0036)

Westendstraße 199, 80686 München

2012/46/EU

Emission No.:

Standard references: EN 60335-1; EN 60335-2-29; EN 60335-2-77; EN 62233;

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 13.11.2017

First CE: 17 Archive-File/Record: NAPR017923

Art.-No.: 30.002.40 I.-No.: 11017 Documents registrar: Alex Kurz

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Only replace the blade with a genuine Ozito replacement blade, as this will ensure top performance

and safety under all conditions.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the

warnings refers to your mains-operated (corded) power tool or battery-operated (cordless)

power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting

to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with

your nger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are dangerous in

the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the power tool

for operations different from those intended could result in a hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger speciﬁed by the manufacturer. A charger that is suitable for one

type of battery pack may create a risk of re when used with another battery pack.

b. Use of any other battery packs may Use power tools only with speciﬁcally designated battery packs.

create a risk of injury and re.

c. When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection from

one terminal to another. Shorting the battery terminals together may cause burns or a re.

d. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualiﬁed repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

b. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualied persons in order to avoid a hazard.

Battery protection system

The tool is equipped with the battery protection system, which helps to ensure a long

service life.

The output power automatically cuts off during operation when the tool and/or battery

are placed under the following situations:

• When the tool is overloaded:

If this occurs, release the start/stop lever safety key and batteries and remove

causes of overload, then reinsert the safety key and batteries, then press and hold

the lock-off button and pull the start stop lever again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The indicated capacity may be lower than the actual level during use or

immediately after using the tool.

LAWN MOWER SAFETY WARNINGS

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Plæneklipper
Model:	PXCLMK-1318EU

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito PXCLMK-1318EU stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Plæneklipper Ozito Manualer

Ozito CPM-300C Manual

10 December 2024

Ozito PXBMK-4047SP Manual

31 August 2024

Ozito ELM-1230 Manual

16 August 2024

Ozito ESA-1231U Manual

15 August 2024

Ozito PXCLMK-218U Manual

13 August 2024

Ozito PXCLMK-1318EU Manual

13 August 2024

Ozito PXCLMK-418U Manual

12 August 2024

Ozito LMPC-301U Manual

12 August 2024

Ozito ELM-1250U Manual

11 August 2024

Ozito ELM-1230U Manual

7 August 2024

Plæneklipper Manualer

Nyeste Plæneklipper Manualer

Philips Series 3000 HC3515 Manual

21 December 2024

Philips Series 3000 HC3507 Manual

21 December 2024

Philips Series 3000 HC3517 Manual

21 December 2024

Philips Series 3000 HC3519 Manual

21 December 2024

Philips Series 3000 HC3516 Manual

21 December 2024

Philips Series 3000 HC3508 Manual

21 December 2024

Philips Series 9000 HC9452 Manual

21 December 2024

Philips Series 3000 HC3409 Manual

21 December 2024

Philips Series 3000 HC3589 Manual

21 December 2024

Philips Series 3000 HC3587 Manual

21 December 2024