Sony RM-V201 Manual

Sony Fjernbetjening RM-V201

Læs nedenfor 📖 manual på dansk for Sony RM-V201 (3 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

Setting Up the Remote Commander

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand

components.

If you’re using the Commander with a Sony component, you won’t

need to preset the Commander before you start using it.

To set up the Commander to use with other (non-Sony)

manufacturers’ components, or to use with a component that is not

preset at the factory, you’ll need to follow the instructions in this

manual to preset the Commander with the correct code number for

your components. (See the supplied “Component Code Numbers”

also.)

Notes

• The Commander can be set up to operate only one component per

button – unless their code numbers happen to be the same. For

example, you cannot set up the Commander to operate a Sony TV

and a Panasonic TV simultaneously (because they use different

code numbers).

• You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in

“Setting the Code.”

Installing the Batteries

Slide open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to line up the + and – on the batteries with the + and – on the

battery compartment.

1 2

When to replace the batteries

Under normal conditions, batteries will last up to 6 months. If the

Commander does not operate properly, the batteries might be worn

out. Replace the batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than 20 minutes to replace the batteries;

otherwise, your setting of the code numbers will be erased.

Notes on Batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use

with the Commander.

Step 1: Entering the Code Number

1 See the supplied “Component Code numbers”, and find the three-

digit code number for the desired component.

If more than one code number is listed, use the number that’s

listed first to complete the steps below.

For example, if you’re setting up a Philips’ VCR, you would use

the code number 035.

If your component isn’t listed, see “Searching for the Correct

Code.”

2 Press and release the S (set) button.

3 Press the button of the component that you want to set up.

TV VCR DVD

CBL/SAT

Note

On the and buttons, “cable box”, and “DVD player”CBL/SAT DVD

are assigned respectively at the factory. But you can also assign other

components on these buttons. For details, see “Changing the

Component Type on the CBL/SAT and DVD buttons.”

4 Enter the component’s code number. For example, if you’re

entering the code for a Philips VCR, you would press .-35

5 Press and release the ENT button to store the code number in the

Commander’s memory.

ENT

6 Go to “Step 2: Checking if the Code Number Works” to finish

setting up.

If you press a wrong button in step 4

Press and release the (set) button and then go back to step 3.S

Step 2: Checking if the Code Number Works

1 Power on the component you want to set up.

2 Aim the Remote Commander at the component and press a button

to check if that button works.

For example, press the button to see if it works on yourPOWER

component .

3 Check that the other buttons of the Commander is operating the

corresponding functions of the component.

If the Commander Doesn’t Seem to Be Working...

• First, try repeating these setup procedures using the other codes

listed for your component (see the supplied “Component Code

Numbers”).

• If – after trying all the codes listed for your component – you still

cannot get the Commander to work properly, try the search

method described in “Searching for the Correct Code.”

Tip

You can write down the code number on the label inside the battery

compartment lid.

Searching for the Correct Code

If you’ve tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component is

not listed in the “Component Code Numbers” tables), try these

steps.

1 Power on the component you want to set up. Insert a tape or disc

if necessary.

2 Press and release the S (set) button.

3 Press the button of the component on the Commander that you

want to set up.

4 Press and release the CH+ button. Then press and release the

POWER button.

5 Repeat step 4 until the correct code number is found.

Each time you press the button and then the CH+ POWER button,

a new code number will be transmitted.

Keep trying until your component operates by receiving the

transmitted signal from the Commander (e.g., the power turns off,

the CH+ function works, playback starts, etc.) Be patient as you do

this; it may take about 70 tries until the correct code number is

located.

6 When the correct code is found, press the ENT button to store the

code number in the Commander’s memory.

7 Check that the Commander is operating the other functions of

your component by pressing the corresponding buttons on the

Commander. If they seem to be working properly, you’re done

setting up the Commander.

If the component does not operate properly, repeat steps 1 to 6 and

search for another code.

If you still cannot get the Commander to work properly, see

“Troubleshooting.”

Changing the Component Type on the CBL/

SAT and DVD buttons

At the factory, “cable box” is assigned on the CBL/SAT button and

“DVD player” on the button. By completing the followingDVD

procedure, you can change this setting so that you can set up any

component on these buttons.

1 Press the S (set) button and release it.

2 Press the CBL/SAT DVD or button.

3 Press and release the x (stop) button.

4 Press and release one of the following buttons;

1 to assign a VCR

3 to assign a digital satellite receiver

8 to assign a TV

9 to assign a cable box

- to assign a DVD player

5 Press and release the ENT button.

6 Enter the component’s code number by following steps 2 to 6 of

“Entering the Code Number”, or steps 1to 7 of “Searching for the

Correct Code.”

Operating a Component

1 Press the button of the desired component on the Commander.

TV VCR DVD

CBL/SAT

2 Point the Commander directly at the component.

3 Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the

buttons on the Commander.

Notes on Using the Remote Commander

Basically, use this Commander in the same way as the Commanders

supplied with your components.

• Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to the

functions of the components themselves. For example, if your TV

does not have a MUTING function, the button on thisMUTING

Commander will not function with your TV.

• Some functions of the component may not work with this

Commander.

• If your cable box can control volume, be sure to set its volume

switch to a medium position. If the volume on the cable box is

turned down completely, you will not be able to adjust your TV’s

volume with the Commander.

Component that can be preset

VCR

Cable box/Digital satellite receiver/

DVD player/TV/VCR

Button

VCR

CBL/SAT

DVD

Factory setting

Sony TV

Sony VHS VCR

—

Sony DVD player

English

3-230-686- (1)11

Remote Commander RM-V201

Operating Instructions

Manual de instrucciones (parte posterior)

Operating a DVD player

3 To select numbers 10 and

above. For example, to select

track 15, press and thenPIP

press .5

4 N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

X: To pause.

5 To display the title menu.

6 To change the sound.

7 To show the current play status

on the screen.

8 To move the cursor upward,

downward, to the left, or to the

right.

Specifications

Operable distance Approx. 7 m (23 ft) (varies depending of the

component of each manufacturer)

Power requirements Two size AA (R6) batteries (not supplied)

Battery life Approx. 6 months (varies depending on frequency of

use)

Dimensions Approx. 51.8 × 195 × 31 mm (w/h/d)

(2 1/ 8× 7 3/ 4× 1 1/4 in.)

Mass Approx. 100 g (3.5 oz.) (not including batteries)

Design and specifications are subject to change without notice.

Troubleshooting

If you have problems setting up or using the Commander:

• When setting up the Commander, carefully go through the procedures

described in “Setting the Code.” If the code that’s listed first for your

component doesn’t work, try all the codes for your component - in the order

in which they’re listed. If all the codes fail to work (or if your component is

not listed in this manual), try using the procedures in “Searching for the

Correct Code.”

• Check that you’re aiming the Commander directly at the component, and that

there are no obstructions between the Commander and the component.

• Make sure the batteries you’re using are not worn out, and that they’re

inserted correctly.

• Check that the button of the , , TV VCR CBL/SAT, or DVD is pressed to choose

your desired component.

• Check that the component has infrared remote capability. For example, if

your component didn’t come with a remote commander, it probably isn’t

capable of being controlled by a remote commander.

• Should any problem persist, reset the Commander to the factory setting by

pressing the buttons simultaneously.POWER TV VIDEO, / and VOL–

For the customers in the U.S.A.

Customer Support Information

If – after you’ve read through this manual – you still cannot get the

Remote Commander to work properly, call the Sony Customer

Support Helpline at 1-800-822-2217.

Operating a TV, VCR, or cable box

3 4 5, , and

TV: To operate the Picture-in-

Picture function. Press each

button or combination of

buttons as described in the

table below.

VCR:

N: To play.

x: To stop.

m: To rewind.

M: To fast-forward.

z NREC: To record, press

while pressing z.

6 TV: To change the input mode.

VCR: To switch the antenna

output.

7 TV: To display the current

channel on TV.

VCR: To expose the on-screen

display.

8 TV/VCR: To move the cursor

upward, downward, to the left,

or to the right.

9 TV/VCR: To call up the MENU

display.

qd and qf

To change the channel. For

example, to change to channel

5, press 0 and (or press and5 5

ENT).

qh TV: To operate SLEEP function

on the TV. (Works only for a

TV with the SLEEP function.)

VCR: To change the input

mode.

qj TV/VCR: To enter the selection.

qk Channel up: +

Channel down: –

ql TV/cable box: To operate

JUMP FLASHBACK, or

CHANNEL RETURN function on

the TV depending on the

setting of the TV’s

manufacturer.

Notes

• There may be cases you may turn on/off the cable box by pressing the CH+ or

CH– buttons on the Commander.

• If your cable box can control volume, be sure to set its volume control to a

medium position. If the volume on the cable box is turned down completely,

you will not be able to adjust your TV’s volume with the Commander.

PIP operations

Press To

PIP Turn on/off the “window” picture.

GUIDE Turn off the “window” picture.

m M or Change the TV channel in the “window” picture.

z Change the input mode of the “window” picture.

x Move the location of the “window” picture.

N Swap the “main” picture and the “window” picture.

X Freeze the “window” picture.

9 To display the DVD menu.

qd Number buttons : To set items

selected from the screen.

qf To enter the setting. To set

items selected from the screen.

qg To clear the selected characters

from the screen.

qh To switch the subtitle.

qj To execute items selected from

the screen.

qk To proceed to next/previous

location or song.

ql To return to the last previous

screen.

RM-V201

MUTING

VOL CH

RECALL

TV/VIDEO

DISP

VCR DVD

POWER

CBL/SAT

REC

PIP ENT

SLEEP GUIDE

MENU OK

Operating a digital satellite receiver

3 To use the “FAVORITE”

function.

4 N: To exit the mode.

6 To switch the output of the

digital satellite receiver to the

TV. (When you connect a TV

cable or antenna to the receiver,

the output switches between a

TV and SAT program.)

8 To scroll through the Master

Guide.

9 To call up the MENU display.

qd and qf

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

qg To bring up the Master Guide.

qh To bring up the Station Index.

qj To select the channel that’s

highlighted. To bring up the

Station Index when a program

guide is not displayed.

qk Channel up: +

Channel down: –

To page through the guide

when a program guide is

displayed.

ql To tune to the last tuned

station.

Remote Button Descriptions

General

1 To set up the Commander.

2 Component select buttons.

To switch to the operations

of each component, press

the button on which that

component is assigned.

q; Volume up: +

Volume down: –

qa To mute the volume on TV.

qs To turn on and off the

power of the selected

component.

Produkt Specifikationer

Mærke:	Sony
Kategori:	Fjernbetjening
Model:	RM-V201

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony RM-V201 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Sony Manualer

16 September 2024

15 September 2024

14 September 2024

9 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

Sony RM-VS10TV Manual

2 September 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Nanlite BT-BCS-48V3.5mm Manual

21 December 2024

SMK-Link VP3700 Manual

17 December 2024

Metronic ZAP 2 Unic - 495399 Manual

17 December 2024

Metronic ZAP 3 - 495373 Manual

17 December 2024

Metronic ZAP 3 - 495309 Manual

17 December 2024

Metronic ZAP 3 - 495308 Manual

17 December 2024

Metronic 495390 Manual

17 December 2024

Metronic 495387 ZAP 3 Manual

17 December 2024

Metronic ZAP 6 Manual

17 December 2024

EQ-3 HM-RC-19-B Manual

16 December 2024