Sony RM-V202 Manual

Sony Fjernbetjening RM-V202

Læs nedenfor 📖 manual på dansk for Sony RM-V202 (3 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 31 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

Installing the Batteries

Before replacing the batteries, have new ones ready beforehand.

Slide open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to line up the + and – on the batteries with the + and – on the

battery compartment.

1 2

When to replace the batteries

Under normal conditions, batteries will last up to 6 months. If the

Commander does not operate properly, the batteries might be worn

out. Replace the batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than 3 minutes to replace the batteries; otherwise,

your setting of the code numbers will be erased.

Notes on Batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use

with the Commander.

Step 1: Entering the Code Number

1 See the supplied “Component Code numbers”, and find the three-

digit code number for the desired component.

If more than one code number is listed, use the number that’s

listed first to complete the steps below.

For example, if you’re setting up a Philips’ VCR, you would use

the code number 035.

If your component isn’t listed, see “Searching for the Correct

Code.”

2 While pressing the button,SET

press the POWER button.

3 Press the button of the

component that you want to set

up.

Note

On the and buttons, “cable box”, and “DVD player”CBL/SAT DVD

are assigned respectively at the factory. But you can also assign other

components on these buttons. For details, see “Changing the

Component Type on the CBL/SAT and DVD buttons.”

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

Setting Up the Remote Commander

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand

components.

If you’re using the Commander with a Sony component, you won’t

need to preset the Commander before you start using it.

To set up the Commander to use with other (non-Sony)

manufacturers’ components, or to use with a component that is not

preset at the factory, you’ll need to follow the instructions in this

manual to preset the Commander with the correct code number for

your components. (See the supplied “Component Code Numbers”

also).

Notes

• The Commander can be set up to operate only one component per

button – unless their code numbers happen to be the same. For

example, you cannot set up the Commander to operate a Sony TV

and a Panasonic TV simultaneously (because they use different

code numbers).

• You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in

“Setting the Code.”

4 Enter the component’s code number. For

example, if you’re entering the code for

a Philips VCR, you would press -35.

5 Press and release the button to storeENT

the code number in the

Commander’s memory.

6 Go to “Step 2: Checking if the Code Number Works” to finish

setting up.

If you press a wrong button in step 4

Press the button while pressing the button and then goPOWER SET

back to step 2.

Step 2: Checking if the Code Number Works

1 Power on the component you want to set up.

2 Aim the Remote Commander at the component and press a button

to check if that button works.

For example, press the button to see if it works on yourPOWER

component .

3 Check that the other buttons of the Commander is operating the

corresponding functions of the component.

You can write down the code number on the label inside the

battery compartment lid.

If the Commander Doesn’t Seem to Be Working...

• First, try repeating these setup procedures using the other codes

listed for your component (see the supplied “Component Code

Numbers”).

• If – after trying all the codes listed for your component – you still

cannot get the Commander to work properly, try the search

method described in “Searching for the Correct Code.”

Searching for the Correct Code

If you’ve tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component is

not listed in the “Component Code Numbers” tables), try these

steps.

1 Power on the component you want to set up. Insert a tape or disc

if necessary.

2 While pressing the SET POWER button, press the button.

3 Press the button of the component on the Commander that you

want to set up.

4 Press and release the CH+ button. Then press and release the

POWER button.

5 Repeat step 4 until the correct code number is found.

Each time you press the button and then the CH+ POWER button,

a new code number will be transmitted.

Keep trying until your component operates by receiving the

transmitted signal from the Commander (e.g., the power turns off,

the CH+ function works, playback starts, etc). Be patient as you do

this; it may take about 70 tries until the correct code number is

located.

6 When the correct code is found, press the button to store theENT

code number in the Commander’s memory.

7 Check that the Commander is operating the other functions of

your component by pressing the corresponding buttons on the

Commander. If they seem to be working properly, you’re done

setting up the Commander.

If the component does not operate properly, repeat steps 1 to 6 and

search for another code.

If you still cannot get the Commander to work properly, see

“Troubleshooting.”

Changing the Component Type on the CBL/

SAT and DVD buttons

At the factory, “cable box” is assigned on the CBL/SAT button and

“DVD player” on the button. By completing the followingDVD

procedure, you can change this setting so that you can set up any

component on these buttons.

1 While pressing the SET POWER button, press the button.

2 Press the CBL/SAT DVD or button.

3 Press and release the x (stop) button.

4 Press and release one of the following buttons;

1 to assign a VCR

2 to assign a DAV

3 to assign a digital satellite receiver, a digital cable box or a

digital video recorder

8 to assign a TV

9 to assign an analog cable box

- to assign a DVD

5 Press and release the ENT button.

6 Enter the component’s code number by following steps 2 to 6 of

“Entering the Code Number”, or steps 1 to 7 of “Searching for the

Correct Code.”

Operating a Component

1 Press the button of the desired component on the Commander.

2 Point the Commander directly at the component.

3 Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the

buttons on the Commander.

Notes on Using the Remote Commander

Basically, use this Commander in the same way as the Commanders

supplied with your components.

• Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to the

functions of the components themselves. For example, if your TV

does not have a MUTING function, the button on thisMUTING

Commander will not function with your TV.

• Some functions of the component may not work with this

Commander.

• If your cable box can control volume, be sure to set its volume

switch to a medium position. If the volume on the cable box is

turned down completely, you will not be able to adjust your TV’s

volume with the Commander.

Component that can be preset

VCR

Analog cable box/Digital cable box/

Digital satellite receiver/DVD/TV/

VCR/Digital video recorder/DAV

Button

VCR

CBL/SAT

DVD

Factory setting

Sony TV

Sony VHS VCR

—

Sony DVD player

English

3-252-842- (1)13

Remote Commander RM-V202

Operating Instructions

Manual de instrucciones (parte posterior)

Operating a DVD

3 To select numbers 10 and

above. For example, to select

track 15, press and thenPIP

press .5

4 To change the sound.

6 To show the current play status

on the screen.

8 To move the cursor upward,

downward, to the left, or to the

right.

9 To display the DVD menu.

0 To record, press N while

pressing .zREC

First release , then releaseN

zREC.

qs Number buttons : To set items

selected from the screen.

qd To enter the setting. To set

items selected from the screen.

Specifications

Operable distance Approx. 7 m (23 ft) (varies depending of the

component of each manufacturer)

Power requirements Two size AA (R6) batteries (not supplied)

Battery life Approx. 6 months (varies depending on frequency of

use)

Dimensions Approx. 55 × 200 × 32 mm (w/h/d)

(2 1/ 4× 7 7/ 8× 1 5/16 in).

Mass Approx. 95 g (3.4 oz). (not including batteries)

Design and specifications are subject to change without notice.

The CE mark on the unit is valid only for products

marketed in the European Union.

Troubleshooting

If you have problems setting up or using the Commander:

• When setting up the Commander, carefully go through the procedures

described in “Setting the Code.” If the code that’s listed first for your

component doesn’t work, try all the codes for your component - in the order

in which they’re listed. If all the codes fail to work (or if your component is

not listed in this manual), try using the procedures in “Searching for the

Correct Code.”

• Check that you’re aiming the Commander directly at the component, and that

there are no obstructions between the Commander and the component.

• Make sure the batteries you’re using are not worn out, and that they’re

inserted correctly.

• Check that the button of the , , , or is pressed to chooseTV VCR CBL/SAT DVD

your desired component.

• Check that the component has infrared remote capability. For example, if

your component didn’t come with a remote commander, it probably isn’t

capable of being controlled by a remote commander.

• Should any problem persist, reset the Commander to the factory setting by

pressing the buttons simultaneously.POWER TV VIDEO, / and VOL–

For the customers in the U.S.A.

Customer Support Information

If – after you’ve read through this manual – you still cannot get the

Remote Commander to work properly, call the Sony Customer

Support Helpline at 1-800-822-2217.

Operating a TV

3 To operate the Picture-in-

Picture function. Press each

button or combination of

buttons as described in the

table below.

4 To change the input mode.

6 To display the current channel

on TV.

8 To move the cursor upward,

downward, to the left, or to the

right.

9 To call up the MENU display.

qs and qd

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

qf Channel up: +

Channel down: –

qg To operate SLEEP function on

the TV. (Works only for a TV

with the SLEEP function).

qh To operate JUMP FLASHBACK,

or CHANNEL RETURN function

on the TV depending on the

setting of the TV’s

manufacturer.

qj To turn off the “window” picture

or select a drive.

qk To enter the selection.

PIP operations

Press To

PIP Turn on/off the “window” picture.

GUIDE Turn off the “window” picture.

m M or Change the TV channel in the “window” picture.

zREC Change the input mode of the “window” picture.

x Move the location of the “window” picture.

N Swap the “main” picture and the “window” picture.

X Freeze the “window” picture.

qf CH+: To proceed to the next

location or song.

Channel up.

CH–: To proceed to the

previous location or song.

Channel down.

qg To switch the subtitle.

qh To display the title menu.

qj To clear the selected characters

from the screen or select a

drive.

qk To execute items selected from

the screen.

ql N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

X: To pause.

Operating a digital satellite receiver

3 To use the “FAVORITE”

function.

4 To switch the output of the

digital satellite receiver to the

TV. (When you connect a TV

cable or antenna to the receiver,

the output switches between a

TV and SAT program).

8 To scroll through the Master

Guide.

9 To call up the MENU display.

qs and qd

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

qf Channel up: +

Channel down: –

To page through the guide

when a program guide is

displayed.

qg To bring up the Station Index.

qh To tune to the last tuned

station.

qj To bring up the Master Guide.

qk To select the channel that’s

highlighted. To bring up the

Station Index when a program

guide is not displayed.

ql N: To exit the mode.

Remote Button Descriptions

General

1 To set up the Commander,

press SET while pressing

POWER.

2 Component select buttons.

To switch to the operations

of each component, press

the button on which that

component is assigned.

5 Volume up: +

Volume down: –

7 To mute the volume on TV.

qa To turn on and off the

power of the selected

component.

POWER

SET

VCRTV CBL / SAT DVD

035

Your Code Number

ENT

VCRTV CBL / SAT DVD

4 5 6

7 8

PIP ENT

POWER

CHVOL

TV / VIDEO

VCRTV

SET

DISPLAY

SLEEP

MUTING RECALL

GUIDEMENU

REC

CBL / SAT DVD

2 3

Operating a VCR

4 To switch the antenna output.

6 To expose the on-screen

display.

8 To move the cursor upward,

downward, to the left, or to the

right.

9 To call up the MENU display.

q; and ql

N: To play.

x: To stop.

m: To rewind.

M: To fast-forward.

z NREC: To record, press

while pressing zREC.

Operating an analog cable box

qs and qd

To change the channel. For

example, to change to channel

5, press 0 and (or press and5 5

ENT).

qf Channel up: +

Channel down: –

Notes

• There may be cases you may turn on/off the cable box by pressing the CH+ or

CH– buttons on the Commander.

• If your cable box can control volume, be sure to set its volume control to a

medium position. If the volume on the cable box is turned down completely,

you will not be able to adjust your TV’s volume with the Commander.

qs and qd

To change the channel. For

example, to change to channel

5, press and (or press and0 5 5

ENT).

qf Channel up: +

Channel down: –

qg To change the input mode.

qj To select a drive.

qk To enter the selection.

qh To operate JUMP FLASHBACK,

or CHANNEL RETURN function

on the TV depending on the

setting of the TV’s

manufacturer.

Operating a DVR (Digital video recorder)

3 (*1LIST)

To call up the title of the

recorded program.

4 To switch the output of the SAT

receiver to the TV.

(When connecting a TV cable or

antenna to the receiver, the

output switches between a TV

and SAT program).

(*1THUMBS+)

To select the desired recorded

program.

(It is necessary to have

recorded the desired program).

6 To turn on the display.

(*1THUMBS–)

To select the desired recorded

program.

(It is necessary to have

recorded the desired program).

8 To move the cursor upward,

downward, to the left, or to the

right.

9 To call up the MENU display.

(*1EPG)

To access to all aspects of the

service.

0 qland

N: To play.

m: To rewind.

M: To fast-forward.

z NREC: To record, press

while pressing zREC.

First release , thenN

release zREC. To stop

recording, perform the

same procedure.

x: To stop.

X: To pause.

qs and qd

To change the channel.

For example, to change to

channel 5, press and (or,0 5

press ).5 and ENT

qf CH+: Channel up.

(*1PAGE+) Page up.

CH–: Channel down.

(*1PAGE–) Page down.

qg To clear the setting.

To exit the setting menu.

qh (*1REPLAY)

To replay.

Or to go into REC/REVIEW

mode during play. (After about

5-second rewind, replay

begins).

qj To bring up Master Guide.

(*1Live TV)

To bring up Master Guide.

qk To bring up the Station Index

when a program guide is not

displayed.

To select the channel that is

highlighted.

*1This key corresponds to Tivo service or the replay service. Refer to its

instruction manual for details.

Operating a digital cable box

3 To use the “FAVORITE” function

4 To switch the output of the SAT

receiver to the TV. (When

connecting a TV cable or

antenna to the receiver, the

output switches between a TV

and SAT program).

6 To turn on the display.

8 To move the cursor upward,

downward, to the left, or to the

right.

9 To call up the MENU display.

0 qland

*2 N: To play.

*2 m: To rewind.

*2 M: To fast-forward.

*2 z NREC: To record, press

while pressing zREC.

First release , thenN

release zREC. To stop

recording, perform the

same procedure.

*2 x: To stop.

*2 X: To pause.

qs and qd

To change the channel.

(for example, to change to

channel 5, press , or0 and 5

press ).5 and ENT

qf CH+: Channel up.

CH–: Channel down.

qg To exit the setting menu.

qh To turn on the display of a

shortcut menu.

qj To call up the title bar and

toggle the title bar on/off in

CABLE mode.

qk To bring up the Station Index

when a program guide is not

displayed.

To select the channel that is

highlighted.

*2The operation of the built-in DVR or the video on demand.

Component code numbers /

Números de código de componentes

English

TV/VCR/COMBO*

The left row of the table shows the brand, the center row shows the

component (TV, VCR or COMBO) and the right row shows the code No.

* COMBO stands for the unit combined with TV and VCR.

Analog cable box, SAT (digital satellite receiver), digital cable box,

DVR (digital video recorder), DVD and DAV

The left row of the table shows the brand and the right row shows

the code No.

Español

TV/VCR/COMBO*

La fila izquierda de la tabla muestra la marca, la central el

componente (televisor (TV), videograbadora (VCR) o COMBO), y

la derecha el número de código.

* COMBO significa que la unidad está combinada con un televisor y una

videograbadora.

CBL (adaptador para cable analógico), SAT (sintonizador de

recepción vía satélite digital), decodificador digital, DVR

(Videograbadora digital), DVD (reproductor de discos DVD) y DAV

La fila izquierda de la tabla muestra la marca y la derecha muestra

el número de código.

To set a Component Code (see the instruction manual for details)

Para introducir un código de componente (consulte los detalles en

el manual de instrucciones)

Code No.

Continued on reverse side / Continúa en el reverso

POWER

SET

c c

ENT

While pressing the button, pressSET

the POWER button.

Al tiempo que mantiene presionado el

botón .SET, presione el botón POWER

DVR (Digital Video Recorder)/

DVR (Videograbadora digital)

Operating a DAV (DVD/Receiver combo)

3 To select numbers 10 and above.

4To change the input mode.

5VOLUME +: .Volume up (DAV)

VOLUME –:Volume down

(DAV).

6To show the current play status

on the screen.

7To mute the volume. Press again

to turn muting off.

8 To move the cursor upward,

downward, to the left, or to the

right.

9To call up the MENU.

qa To turn the power on/off.

qs Number buttons: To set items

selected on the screen.

qd To enter the setting.

qf CHANNEL +:Presetting or

turning frequency

to a higher: +

CHANNEL –:Presetting or

turning frequency

to a lower: –.

qg To switch the subtitle.

qh To display the Top Menu.

qj To change the sound.

qk To enter the selection of the

MENU display.

ql N: To play.

m: To rewind.

M: To fast-forward.

x: To stop.

X: To pause.

VCRTV CBL / SAT DVD

DAV (DVD/Amplifier)

DAV (DVD/amplificador)

Brand

Sony

Bose

Insignia

JVC

Onkyo

Panasonic

Samsung

Sharp

Yamaha

Zenith

Code No.

001, 002, 003, 004, 005

012

015

007

014, 016

009

006

008

010

011

013

Brand

JVC

Code No.

035, 036

Dish Network

ReplayTV

Brand

Panasonic

ReplayTV

Code No.

021

022

Brand

DirecTV

Code No.

037

DirecTV

Brand

Sony

Philips

Code No.

017, 018, 019

020

Tivo DVD

Brand

Sony

Aiwa

Cyber Home

Daewoo

Denon

Emerson

Harman/Kardon

Hitachi

ILO

Insignia

JVC

KLH

Magnabox

Onkyo

Orion

Panasonic

Philips

Pioneer

RCA

Samsung

Sanyo

Sharp

Shinco

Symphonic

Sylvania

Terapin

Thomson

Toshiba

Yamaha

Zenith

Code No.

001, 023, 024, 025, 030, 031, 032, 040,

050

015

054, 055, 067

029

006, 017

051, 060, 069

018

008

068, 071

072, 073

007, 037

010

059, 066

016

052, 058

002, 006, 027, 028, 034, 035, 036, 042,

045, 053

012, 062

004, 019, 021, 033, 063, 064

005

014, 041, 070

057

011, 048

022

060, 061

020, 044, 049

056

013

003, 038, 039, 046, 065

006

009, 047

SAT

Brand

DirecTV Sony

DirecTV

Hitachi

Hughes

Panasonic

RCA/Proscan

Toshiba

Dish Network JVC

Code No.

001

025, 041, 042

005

004

003

002, 007

006

010

Digital cable box/Decodificador digital

Code No.

013

044

046

044

015

021

016

044

014, 045

047

Brand

Sony

Adelphia

Americast

Cablevision

Jerrold/G.I.

Motorola

Panasonic

Philips

Pioneer

Scientific Atlanta

Zenith

Analog cable box/

Adaptador para cable analógico

Code No.

002, 003, 009, 032, 046

022, 023, 024, 025, 026

031, 001, 002, 003, 004, 005, 006, 007,

008, 018, 022, 032

027, 028, 029

019, 020, 021

014, 015

009, 010, 011

031, 016, 017, 045

012, 013

Brand

ABC

Hamlin/Regal

Jerrold/G.I

Oak

Panasonic

Pioneer

Scientific Atlanta

Tocom

Zenith

Produkt Specifikationer

Mærke:	Sony
Kategori:	Fjernbetjening
Model:	RM-V202
Vægt:	- g
Produktfarve:	Sølv
Indbygget skærm:	Ingen
Grænseflade:	IR trådløs
Mærke kompatibilitet:	Alle mærker
Fjernbetjening korrekt brug:	DVD/Blu-ray,SAT,TV,VCR
Indgangstype:	Tryk på knapper
Maks. rækkevidde:	- m
Antal understøttede enheder:	4