ESQ Aston Chronograph Manual

ESQ Ur Aston Chronograph

Læs nedenfor 📖 manual på dansk for ESQ Aston Chronograph (2 sider) i kategorien Ur. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Operating Instructions
ASTON 1/5 CHRONOGRAPH
A chronograph combines two time-keeping functions. It incorporates
a device to measure intervals of time independent of the regular time
shown on the dial. Your ESQ by Movado Aston Chronograph may be
used to time events up to two hours in duration, in 1/5 of-a-second
increments.
NOTE: After 2 hours of continuous running, the chronograph will stop
and reset automatically to preserve battery life.
Setting the Time:
1. Pull crown out to position 3. (Watch will stop.)
2. Turn crown in either direction to move hands to desired time.
Be sure to take AM/PM into account so that date changes at midnight,
not noon.
3. Push crown back in to position 1. (Watch will restart.)
NOTE: To set time to exact second, pull crown out to position 2 precisely
when small seconds hand S reaches <<60>> position. (Watch stops.)
Adjust time to one minute ahead, and take an accurate time signal, from
a radio news station, for example. When audible tone signals exact time,
immediately push crown back in to position 1. (Watch will restart, now
set to the exact time.)
Setting the Day:
1. Pull crown out to position 3. (Watch will stop.)
2. Turn crown in either direction to move hands forward or back. Each
time the hands complete a 24-hour revolution and pass midnight,
Day indicator hand F will move ahead or back by one day.
3. Once correct Day has been reached, set hands to correct Time,
following instructions above.
4. Push crown back in to position 1. (Watch will restart.)
Setting the Date:
1. Pull crown out to position 2. (Watch will keep running.)
2. Turn crown clockwise to move hands forward. Each time the hands
complete a 24-hour revolution and pass midnight, the date shown in
Date display D will advance by one number.
3. Once correct Date has been reached, push crown back in to position 1.
CAUTION: Never set the date when the hands are between 9:00 PM
and 12:30 AM, while automatic date changing is in progress. Doing so
could damage the calendar mechanism.
Chronograph Function Overview
Use buttons A and B to operate the chronograph. Pressing button A
the first time will start the chronograph. While the chronograph is run-
ning, once the chronograph fifths-of-a-second counter hand C has com-
pleted one turn, minute-counter hand E will jump ahead one minute.
Pressing button A a second time will stop the chronograph. Pressing
button B will reset chronograph hands E and C to zero. Adjusting the
time does not stop the chronograph, but it does block buttons A and B
for as long as the crown is pulled out.
IMPORTANT: Crown must be in position 1 and hands must be at zero
before chronograph is started. Press button B to reset hands to zero.
Do not push button A or B while crown is pulled to position 2 or 3.
If button A or B is accidentally activated while crown is not flush against
case, one or both chronograph hands may become de-synchronized.
Should this occur, see directions for synchronizing hands at end of
following instructions.
Simple chronograph functions:
To measure the duration of a single, non-stop event:
1. Press button A to start chronograph.
2. Press button A a second time to stop chronograph, and read the 2
chronograph hands to determine elapsed time, for example: 14 minutes;
37 and 3/5 of a second.
3. Press button B to reset chronograph to zero.
Accumulated time functions:
To measure the combined time of a series of shorter events, for example
the actual playing time of a football game, where play is repeatedly
interrupted:
1. Press button A to start chronograph.
2. Press button A a second time to stop chronograph.
3. Press button A again to resume measurement.
4. Press button A a fourth time to stop chronograph again.
NOTE: Each time you stop chronograph, chronograph hands will indicate
total accumulated time.
Repeat steps 1 and 2 to add each additional interval of time.
5. After you have taken your final accumulated time reading, press button
B to reset chronograph hands to zero.
Split-time or intermediate time functions:
To take intermediate time readings as a race progresses:
1. Press button A to start chronograph.
2. Press button B to momentarily stop chronograph.
3. Read off the intermediate time, for example:10 minutes, 26 and 2/5
of a second.
Legend
H - Hour hand
M - Minute hand
S - Small seconds hand
F - Day indicator hand
C - Center-mounted chronograph fifths-of-a-second hand
E - Chronograph 30-minutes counter
D - Date display
1, 2, 3 - Crown positions
A - Chronograph start/stop push-button
B - Chronograph split/reset push-button
20
28
30
S
S
F
T
T
M
W
10 40
0
20
E
1
A
B
C
D
F
2
S
HM
3

Produkt Specifikationer

Mærke: ESQ
Kategori: Ur
Model: Aston Chronograph

Har du brug for hjælp?

Hvis du har brug for hjælp til ESQ Aston Chronograph stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ur ESQ Manualer

ESQ

ESQ Pipeline with Tide Movement Manual

16 August 2024
ESQ

ESQ Beacon Chronograph Manual

12 August 2024
ESQ

ESQ Aston Chronograph Manual

11 August 2024
ESQ

ESQ Quest Retrograde Manual

11 August 2024
ESQ

ESQ Analog - Digital Chronograph Manual

10 August 2024
ESQ

ESQ Analog Chronograph with Alarm Manual

10 August 2024

Ur Manualer

Nyeste Ur Manualer

Diesel

Diesel Rasp Nsbb DZ1872 Manual

15 December 2024
Fossil

Fossil Collider Hybrid HR FTW7009 Manual

15 December 2024
Fossil

Fossil Neutra Hybrid HR FTW7027 Manual

15 December 2024
Fossil

Fossil Neutra Hybrid HR FTW7025 Manual

15 December 2024
Fossil

Fossil Monroe Hybrid HR FTW7035 Manual

15 December 2024
Fossil

Fossil Collider Hybrid HR FTW7008 Manual

15 December 2024
Fossil

Fossil Monroe Hybrid HR FTW7039 Manual

15 December 2024
Ice Watch

Ice Watch Ola Kids Manual

15 December 2024
TFA

TFA 60.4512.01 Manual

14 December 2024
Oregon Scientific

Oregon Scientific PrysmaChrome BAR292A Manual

14 December 2024