Eureka Juno 3XTA Manual

Eureka Fuld Juno 3XTA

Læs nedenfor 📖 manual på dansk for Eureka Juno 3XTA (2 sider) i kategorien Fuld. Denne guide var nyttig for 37 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
ASSEMBLY INSTRUCTIONS
for the JUNO 3XTA TENT
fig 7 fig 8
fig 9
Component List:
1 Tent Body, 2 Tent Poles, 1 Carry Bag,
1 Tent Fly, 1 Stake Bag/ Stakes
Unroll and unfold the tent with the floor on the ground.
Remove the fly and set it aside. Do not stake the tent
down yet. In windy conditions, we recommend that the
mesh end should face into the wind and that you stake
down one corner of this end.
Join the shock-corded poles together. Try to prevent
pole sections from snapping together, as this can
damage the pole ends. NOTE: Make certain each
insert end has seated firmly into each plain end.
See fig 1.
At the front corner of the tent- , A
slide the ball end of one of the
aluminum poles into the rod
sleeve. Angle the pole to the
opposite corner; to . At corner A C
B , repeat with the second pole
and sleeve; to . B D
See fig. 1 and 2.
Start at the front of the tent at , grasp the D
end of the pole in one hand and the web
loop in the other. Push the pole from to D B
creating an arc. Insert the pin into the pole
ferrule to tension the tent across the seam
line. Repeat with the other pole; to . C A
See fig 3 and 4.
With the tent secure, drape the fly over the tent body. The fly only fits
on the tent one way. Position the fly over the tent with the vestibule
wing sections over the doors and with the section over the all mesh !
end of the tent. Reach under the fly and connect the hook and loop
tabs to the tent poles. See fig 7.
Connect the four corner buckles on the fly to their mates on the tent
webs. Do not fully tighten down any of the webs just yet.
See fig 8.
At the front of the tent, pull the stake out loop on the vestibule taut
and stake it down. Make sure that the vestibule is tight across the
door. Repeat with the second vestibule at the rear of the tent.
See fig 9.
With the vestibule wing sections staked down and tight, go to the open
side of the tent, pull out the vent and hold it in place with the hook
and loop tab. Then adjust and tighten all the remaining side release
buckles.
Your tent is now ready for use.
NOTE: I
n strong winds, tie extra cords to the storm loops on the fly and
stake down so that the cords are tight.
Take down:
Pull up stakes and open doors. Remove the fly. Pull pins out of
the poles. Un-clip, collapse the tent poles and stow in the pole bag. Fold the
tent and the fly. Roll up both along with the pole bag towards the door and
stow all in the main bag.
REV.B 2-10
A
B
C
Dfig. 1
fig. 2
fig 3
fig 4
fig 5
fig 7
fig 6
A
B
C
D
Raise up both poles and attach the peak of
the tent to them. Capture the poles, where
they cross, with the tent clips. Then attach
all remaining clips to the poles.
See fig 5.
Your tent is now free-standing, place it in
location that has enough room for the fly
and stake it down through the corner rings.
Stake the opposite corners while applying
tension to smooth the floor wrinkles.
See fig 6 and 7.
NOTE: General purpose stakes are included
but snow or sand stakes can be purchased
at a Eureka! dealer.


Produkt Specifikationer

Mærke: Eureka
Kategori: Fuld
Model: Juno 3XTA

Har du brug for hjælp?

Hvis du har brug for hjælp til Eureka Juno 3XTA stil et spørgsmål nedenfor, og andre brugere vil svare dig