Mikrotik RB450Gx4 Manual

Mikrotik Router RB450Gx4

Læs nedenfor 📖 manual på dansk for Mikrotik RB450Gx4 (3 sider) i kategorien Router. Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
RouterBOARD 450Gx4
First use
The RB450Gx4 is an Ethernet router with five Gigabit Ethernet ports, a serial port, two power jacks and a microSD
card slot. It is powered by MikroTik RouterOS. It comes without an enclosure, you are free to use it in your own.
Install the board in a case.
Connect Ethernet cables and plug in the microSD card (optional).
Plug in power cable, or PoE powered ethernet cable in Ether1 to turn on the device.
Powering
The device accepts power in the following ways:
direct-input power jacks J1/J2 (5.5mm outside and 2mm inside diameter, female, pin positive plug) both
accept 10-57V DC.
Ether1 Ethernet port accepts 12-57V DC input (at the board; higher voltage needed to compensate for
power loss on long cables) from 802.3af/at or passive Power over Ethernet sources.
Max total power consumption with all interfaces loaded is 5 W. You can use any or all inputs at the same time, they
will work in failover mode.
Booting process
RouterOS is the operating system of all RouterBOARD routers. Please see documentation: http://mt.lv/help
This device is not preconfigured other than an IP address on the ethernet port. Other configuration has to be
applied according to the documentation manual linked above.
Initial connection has to be done via the ethernet cable, using the MikroTik Winbox utility. Winbox should be used to
connect to the default IP address of 192.168.88.1 with the username admin and no password.
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the reset button of
the device when starting it until the LED light turns off, and the device will start to look for Netinstall servers.
In case IP connection is not available, the Winbox utility can also be used to connect to the MAC address of the
device. More information in the documentation.
Extension slots and ports
Five Gigabit Ethernet ports (Auto MDI/X). The first Ethernet port accepts 8-30V DC powering from a
passive PoE injector or 802.3af/at PoE switch. Use 12V or more to compensate for any losses in cables.
The other four Ethernet ports do not support PoE input.
The Ether5 port is capable of powering another RouterBOARD device with passive PoE (up to 57 V). The
maximum output current is 500 mA.
Onboard DB9 RS232C asynchronous serial port is set by default to 115200bit/s, 8 data bits, 1 stop bit, no
parity. Note that the device does not fully implement the hardware (RTS/CTS) flow control, so it is
suggested to try to disable hardware flow control in the terminal emulation program.
microSD card for additional file storage.
See www. mikrotik .com support@mikrotik.com for more information. Contact for support questions. Document # . Modified on 03/27/1839209


Produkt Specifikationer

Mærke: Mikrotik
Kategori: Router
Model: RB450Gx4

Har du brug for hjælp?

Hvis du har brug for hjælp til Mikrotik RB450Gx4 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Router Mikrotik Manualer

Router Manualer

Nyeste Router Manualer

Huawei

Huawei E5785-320 Manual

23 Februar 2025
Huawei

Huawei E5785-330 Manual

23 Februar 2025
Huawei

Huawei E5180 Manual

20 Februar 2025
Teltonika

Teltonika RUTM52 Manual

12 Februar 2025
Teltonika

Teltonika RUTM51 Manual

12 Februar 2025
Rocstor

Rocstor Y10A267-A1 Manual

10 Februar 2025
Teltonika

Teltonika RUT901 Manual

3 Februar 2025
Strong

Strong SW8000P Manual

31 Januar 2025